snowball: Add support for ux500 based snowball board
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/gpio/Makefile
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index c77c631..3c67599 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -42,6 +42,7 @@
COBJS-$(CONFIG_MPC83XX_GPIO) += mpc83xx_gpio.o
COBJS-$(CONFIG_SH_GPIO_PFC) += sh_pfc.o
COBJS-$(CONFIG_OMAP_GPIO) += omap_gpio.o
+COBJS-$(CONFIG_DB8500_GPIO) += db8500_gpio.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/gpio/db8500_gpio.c b/drivers/gpio/db8500_gpio.c
new file mode 100644
index 0000000..d5cb383
--- /dev/null
+++ b/drivers/gpio/db8500_gpio.c
@@ -0,0 +1,221 @@
+/*
+ * Code ported from Nomadik GPIO driver in ST-Ericsson Linux kernel code.
+ * The purpose is that GPIO config found in kernel should work by simply
+ * copy-paste it to U-boot.
+ *
+ * Original Linux authors:
+ * Copyright (C) 2008,2009 STMicroelectronics
+ * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
+ * Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com>
+ *
+ * Ported to U-boot by:
+ * Copyright (C) 2010 Joakim Axelsson <joakim.axelsson AT stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+
+#include <asm/arch/db8500_gpio.h>
+#include <asm/arch/db8500_pincfg.h>
+#include <linux/compiler.h>
+
+#define IO_ADDR(x) (void *) (x)
+
+/*
+ * The GPIO module in the db8500 Systems-on-Chip is an
+ * AMBA device, managing 32 pins and alternate functions. The logic block
+ * is currently only used in the db8500.
+ */
+
+#define GPIO_TOTAL_PINS 268
+#define GPIO_PINS_PER_BLOCK 32
+#define GPIO_BLOCKS_COUNT (GPIO_TOTAL_PINS/GPIO_PINS_PER_BLOCK + 1)
+#define GPIO_BLOCK(pin) (((pin + GPIO_PINS_PER_BLOCK) >> 5) - 1)
+#define GPIO_PIN_WITHIN_BLOCK(pin) ((pin)%(GPIO_PINS_PER_BLOCK))
+
+/* Register in the logic block */
+#define DB8500_GPIO_DAT 0x00
+#define DB8500_GPIO_DATS 0x04
+#define DB8500_GPIO_DATC 0x08
+#define DB8500_GPIO_PDIS 0x0c
+#define DB8500_GPIO_DIR 0x10
+#define DB8500_GPIO_DIRS 0x14
+#define DB8500_GPIO_DIRC 0x18
+#define DB8500_GPIO_SLPC 0x1c
+#define DB8500_GPIO_AFSLA 0x20
+#define DB8500_GPIO_AFSLB 0x24
+
+#define DB8500_GPIO_RIMSC 0x40
+#define DB8500_GPIO_FIMSC 0x44
+#define DB8500_GPIO_IS 0x48
+#define DB8500_GPIO_IC 0x4c
+#define DB8500_GPIO_RWIMSC 0x50
+#define DB8500_GPIO_FWIMSC 0x54
+#define DB8500_GPIO_WKS 0x58
+
+static void __iomem *get_gpio_addr(unsigned gpio)
+{
+ /* Our list of GPIO chips */
+ static void __iomem *gpio_addrs[GPIO_BLOCKS_COUNT] = {
+ IO_ADDR(CFG_GPIO_0_BASE),
+ IO_ADDR(CFG_GPIO_1_BASE),
+ IO_ADDR(CFG_GPIO_2_BASE),
+ IO_ADDR(CFG_GPIO_3_BASE),
+ IO_ADDR(CFG_GPIO_4_BASE),
+ IO_ADDR(CFG_GPIO_5_BASE),
+ IO_ADDR(CFG_GPIO_6_BASE),
+ IO_ADDR(CFG_GPIO_7_BASE),
+ IO_ADDR(CFG_GPIO_8_BASE)
+ };
+
+ return gpio_addrs[GPIO_BLOCK(gpio)];
+}
+
+static unsigned get_gpio_offset(unsigned gpio)
+{
+ return GPIO_PIN_WITHIN_BLOCK(gpio);
+}
+
+/* Can only be called from config_pin. Don't configure alt-mode directly */
+static void gpio_set_mode(unsigned gpio, enum db8500_gpio_alt mode)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+ u32 bit = 1 << offset;
+ u32 afunc, bfunc;
+
+ afunc = readl(addr + DB8500_GPIO_AFSLA) & ~bit;
+ bfunc = readl(addr + DB8500_GPIO_AFSLB) & ~bit;
+ if (mode & DB8500_GPIO_ALT_A)
+ afunc |= bit;
+ if (mode & DB8500_GPIO_ALT_B)
+ bfunc |= bit;
+ writel(afunc, addr + DB8500_GPIO_AFSLA);
+ writel(bfunc, addr + DB8500_GPIO_AFSLB);
+}
+
+/**
+ * db8500_gpio_set_pull() - enable/disable pull up/down on a gpio
+ * @gpio: pin number
+ * @pull: one of DB8500_GPIO_PULL_DOWN, DB8500_GPIO_PULL_UP,
+ * and DB8500_GPIO_PULL_NONE
+ *
+ * Enables/disables pull up/down on a specified pin. This only takes effect if
+ * the pin is configured as an input (either explicitly or by the alternate
+ * function).
+ *
+ * NOTE: If enabling the pull up/down, the caller must ensure that the GPIO is
+ * configured as an input. Otherwise, due to the way the controller registers
+ * work, this function will change the value output on the pin.
+ */
+void db8500_gpio_set_pull(unsigned gpio, enum db8500_gpio_pull pull)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+ u32 bit = 1 << offset;
+ u32 pdis;
+
+ pdis = readl(addr + DB8500_GPIO_PDIS);
+ if (pull == DB8500_GPIO_PULL_NONE)
+ pdis |= bit;
+ else
+ pdis &= ~bit;
+ writel(pdis, addr + DB8500_GPIO_PDIS);
+
+ if (pull == DB8500_GPIO_PULL_UP)
+ writel(bit, addr + DB8500_GPIO_DATS);
+ else if (pull == DB8500_GPIO_PULL_DOWN)
+ writel(bit, addr + DB8500_GPIO_DATC);
+}
+
+void db8500_gpio_make_input(unsigned gpio)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+
+ writel(1 << offset, addr + DB8500_GPIO_DIRC);
+}
+
+int db8500_gpio_get_input(unsigned gpio)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+ u32 bit = 1 << offset;
+
+ printf("db8500_gpio_get_input gpio=%u addr=%p offset=%u bit=%#x\n",
+ gpio, addr, offset, bit);
+
+ return (readl(addr + DB8500_GPIO_DAT) & bit) != 0;
+}
+
+void db8500_gpio_make_output(unsigned gpio, int val)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+
+ writel(1 << offset, addr + DB8500_GPIO_DIRS);
+ db8500_gpio_set_output(gpio, val);
+}
+
+void db8500_gpio_set_output(unsigned gpio, int val)
+{
+ void __iomem *addr = get_gpio_addr(gpio);
+ unsigned offset = get_gpio_offset(gpio);
+
+ if (val)
+ writel(1 << offset, addr + DB8500_GPIO_DATS);
+ else
+ writel(1 << offset, addr + DB8500_GPIO_DATC);
+}
+
+/**
+ * config_pin - configure a pin's mux attributes
+ * @cfg: pin confguration
+ *
+ * Configures a pin's mode (alternate function or GPIO), its pull up status,
+ * and its sleep mode based on the specified configuration. The @cfg is
+ * usually one of the SoC specific macros defined in mach/<soc>-pins.h. These
+ * are constructed using, and can be further enhanced with, the macros in
+ * plat/pincfg.h.
+ *
+ * If a pin's mode is set to GPIO, it is configured as an input to avoid
+ * side-effects. The gpio can be manipulated later using standard GPIO API
+ * calls.
+ */
+static void config_pin(unsigned long cfg)
+{
+ int pin = PIN_NUM(cfg);
+ int pull = PIN_PULL(cfg);
+ int af = PIN_ALT(cfg);
+ int output = PIN_DIR(cfg);
+ int val = PIN_VAL(cfg);
+
+ if (output)
+ db8500_gpio_make_output(pin, val);
+ else {
+ db8500_gpio_make_input(pin);
+ db8500_gpio_set_pull(pin, pull);
+ }
+
+ gpio_set_mode(pin, af);
+}
+
+/**
+ * db8500_config_pins - configure several pins at once
+ * @cfgs: array of pin configurations
+ * @num: number of elments in the array
+ *
+ * Configures several pins using config_pin(). Refer to that function for
+ * further information.
+ */
+void db8500_gpio_config_pins(unsigned long *cfgs, size_t num)
+{
+ size_t i;
+
+ for (i = 0; i < num; i++)
+ config_pin(cfgs[i]);
+}
diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c
index ed581ae..d4c5137 100644
--- a/drivers/serial/serial_pl01x.c
+++ b/drivers/serial/serial_pl01x.c
@@ -156,6 +156,8 @@
writel(lcr, ®s->fr);
writel(lcr, ®s->pl011_rlcr);
+ /* lcrh needs to be set again for change to be effective */
+ writel(lcr, ®s->pl011_lcrh);
}
#endif
/* Finally, enable the UART */