TI: OMAP3: Overo Tobi ethernet support
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
diff --git a/board/overo/overo.c b/board/overo/overo.c
index dd6d286..d42dc13 100644
--- a/board/overo/overo.c
+++ b/board/overo/overo.c
@@ -29,13 +29,20 @@
* MA 02111-1307 USA
*/
#include <common.h>
+#include <netdev.h>
#include <twl4030.h>
#include <asm/io.h>
#include <asm/arch/mux.h>
+#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
+#include <asm/arch/gpio.h>
#include <asm/mach-types.h>
#include "overo.h"
+#if defined(CONFIG_CMD_NET)
+static void setup_net_chip(void);
+#endif
+
/*
* Routine: board_init
* Description: Early hardware init.
@@ -62,6 +69,10 @@
twl4030_power_init();
twl4030_led_init();
+#if defined(CONFIG_CMD_NET)
+ setup_net_chip();
+#endif
+
dieid_num_r();
return 0;
@@ -77,3 +88,51 @@
{
MUX_OVERO();
}
+
+#if defined(CONFIG_CMD_NET)
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ * Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+ struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
+
+ /* Configure GPMC registers */
+ writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
+ writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
+ writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
+ writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
+ writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
+ writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
+ writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
+
+ /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+ writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+ /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+ /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+ &ctrl_base->gpmc_nadv_ale);
+
+ /* Make GPIO 64 as output pin and send a magic pulse through it */
+ if (!omap_request_gpio(64)) {
+ omap_set_gpio_direction(64, 0);
+ omap_set_gpio_dataout(64, 1);
+ udelay(1);
+ omap_set_gpio_dataout(64, 0);
+ udelay(1);
+ omap_set_gpio_dataout(64, 1);
+ }
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}