diff --git a/board/toradex/apalis-imx8/Kconfig b/board/toradex/apalis-imx8/Kconfig
new file mode 100644
index 0000000..c680d63
--- /dev/null
+++ b/board/toradex/apalis-imx8/Kconfig
@@ -0,0 +1,30 @@
+if TARGET_APALIS_IMX8
+
+config SYS_BOARD
+	default "apalis-imx8"
+
+config SYS_VENDOR
+	default "toradex"
+
+config SYS_CONFIG_NAME
+	default "apalis-imx8"
+
+config TDX_CFG_BLOCK
+	default y
+
+config TDX_HAVE_MMC
+	default y
+
+config TDX_CFG_BLOCK_DEV
+	default "0"
+
+config TDX_CFG_BLOCK_PART
+	default "1"
+
+# Toradex config block in eMMC, at the end of 1st "boot sector"
+config TDX_CFG_BLOCK_OFFSET
+	default "-512"
+
+source "board/toradex/common/Kconfig"
+
+endif
diff --git a/board/toradex/apalis-imx8/MAINTAINERS b/board/toradex/apalis-imx8/MAINTAINERS
new file mode 100644
index 0000000..c9ac58b
--- /dev/null
+++ b/board/toradex/apalis-imx8/MAINTAINERS
@@ -0,0 +1,9 @@
+Apalis iMX8
+M:	Marcel Ziswiler <marcel.ziswiler@toradex.com>
+W:	http://developer.toradex.com/software/linux/linux-software
+S:	Maintained
+F:	arch/arm/dts/fsl-imx8-apalis.dts
+F:	arch/arm/dts/fsl-imx8-apalis-u-boot.dtsi
+F:	board/toradex/apalis-imx8/
+F:	configs/apalis-imx8qm_defconfig
+F:	include/configs/apalis-imx8.h
diff --git a/board/toradex/apalis-imx8/Makefile b/board/toradex/apalis-imx8/Makefile
new file mode 100644
index 0000000..a8c3eb7
--- /dev/null
+++ b/board/toradex/apalis-imx8/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2019 Toradex
+#
+
+obj-y += apalis-imx8.o
diff --git a/board/toradex/apalis-imx8/README b/board/toradex/apalis-imx8/README
new file mode 100644
index 0000000..e6e3dcb
--- /dev/null
+++ b/board/toradex/apalis-imx8/README
@@ -0,0 +1,66 @@
+U-Boot for the Toradex Apalis iMX8QM V1.0B Module
+
+Quick Start
+===========
+
+- Build the ARM trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Build U-Boot
+- Load U-Boot binary using uuu
+- Flash U-Boot binary into the eMMC
+- Boot
+
+Get and Build the ARM Trusted Firmware
+======================================
+
+$ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atf/
+$ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+=======================================
+
+$ wget https://github.com/toradex/meta-fsl-bsp-release/blob/toradex-sumo-4.14.78-1.0.0_ga-bringup/imx/meta-bsp/recipes-bsp/imx-sc-firmware/files/mx8qm-apalis-scfw-tcm.bin?raw=true
+$ mv mx8qm-apalis-scfw-tcm.bin\?raw\=true mx8qm-apalis-scfw-tcm.bin
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+$ chmod +x firmware-imx-8.0.bin
+$ ./firmware-imx-8.0.bin
+
+Copy the following binaries to the U-Boot folder:
+
+$ cp imx-atf/build/imx8qm/release/bl31.bin .
+$ cp u-boot/u-boot.bin .
+
+Copy the following firmware to the U-Boot folder:
+
+$ cp firmware-imx-8.0/firmware/seco/ahab-container.img .
+
+Build U-Boot
+============
+
+$ make apalis-imx8qm_defconfig
+$ make u-boot-dtb.imx
+
+Load the U-Boot Binary Using UUU
+================================
+
+Get the latest version of the universal update utility (uuu) aka mfgtools 3.0:
+
+https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases
+
+Put the module into USB recovery aka serial downloader mode, connect USB device
+to your host and execute uuu:
+
+sudo ./uuu u-boot/u-boot-dtb.imx
+
+Flash the U-Boot Binary into the eMMC
+=====================================
+
+Burn the u-boot-dtb.imx binary to the primary eMMC hardware boot area partition:
+
+load mmc 1:1 $loadaddr u-boot-dtb.imx
+setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200
+mmc dev 0 1
+mmc write ${loadaddr} 0x0 ${blkcnt}
+
+Boot
diff --git a/board/toradex/apalis-imx8/apalis-imx8.c b/board/toradex/apalis-imx8/apalis-imx8.c
new file mode 100644
index 0000000..f516e54
--- /dev/null
+++ b/board/toradex/apalis-imx8/apalis-imx8.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 Toradex
+ */
+
+#include <common.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <environment.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+
+#include "../common/tdx-cfg-block.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			 (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			 (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			 (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart1_pads[] = {
+	SC_P_UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	SC_P_UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx8_iomux_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+int board_early_init_f(void)
+{
+	sc_pm_clock_rate_t rate;
+	sc_err_t err = 0;
+
+	/* Power up UART1 */
+	err = sc_pm_set_resource_power_mode(-1, SC_R_UART_1, SC_PM_PW_MODE_ON);
+	if (err != SC_ERR_NONE)
+		return 0;
+
+	/* Set UART3 clock root to 80 MHz */
+	rate = 80000000;
+	err = sc_pm_set_clock_rate(-1, SC_R_UART_1, SC_PM_CLK_PER, &rate);
+	if (err != SC_ERR_NONE)
+		return 0;
+
+	/* Enable UART1 clock root */
+	err = sc_pm_clock_enable(-1, SC_R_UART_1, SC_PM_CLK_PER, true, false);
+	if (err != SC_ERR_NONE)
+		return 0;
+
+	setup_iomux_uart();
+
+	return 0;
+}
+
+#if IS_ENABLED(CONFIG_DM_GPIO)
+static void board_gpio_init(void)
+{
+	/* TODO */
+}
+#else
+static inline void board_gpio_init(void) {}
+#endif
+
+#if IS_ENABLED(CONFIG_FEC_MXC)
+#include <miiphy.h>
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+void build_info(void)
+{
+	u32 sc_build = 0, sc_commit = 0;
+
+	/* Get SCFW build and commit id */
+	sc_misc_build_info(-1, &sc_build, &sc_commit);
+	if (!sc_build) {
+		printf("SCFW does not support build info\n");
+		sc_commit = 0; /* Display 0 if build info not supported */
+	}
+	printf("Build: SCFW %x\n", sc_commit);
+}
+
+int checkboard(void)
+{
+	puts("Model: Toradex Apalis iMX8\n");
+
+	build_info();
+	print_bootinfo();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	board_gpio_init();
+
+	return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+	/* TODO */
+}
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return ft_common_board_setup(blob, bd);
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+	return devno;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+/* TODO move to common */
+	env_set("board_name", "Apalis iMX8QM");
+	env_set("board_rev", "v1.0");
+#endif
+
+	return 0;
+}
diff --git a/board/toradex/apalis-imx8/apalis-imx8qm-imximage.cfg b/board/toradex/apalis-imx8/apalis-imx8qm-imximage.cfg
new file mode 100644
index 0000000..71981f8
--- /dev/null
+++ b/board/toradex/apalis-imx8/apalis-imx8qm-imximage.cfg
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2019 Toradex
+ *
+ * Refer doc/README.imx8image for more details about how-to configure
+ * and create imx8image boot image
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM EMMC_FASTBOOT 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-apalis-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000