i2c, zynq: convert zynq i2c driver to new multibus/multiadapter framework
- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 298b17b..9dd9094 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -28,4 +28,4 @@
obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
-obj-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o
+obj-$(CONFIG_SYS_I2C_ZYNQ) += zynq_i2c.o
diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c
index ce2d23f..70a9aea 100644
--- a/drivers/i2c/zynq_i2c.c
+++ b/drivers/i2c/zynq_i2c.c
@@ -74,7 +74,8 @@
(struct zynq_i2c_registers *)ZYNQ_I2C_BASE;
/* I2C init called by cmd_i2c when doing 'i2c reset'. */
-void i2c_init(int requested_speed, int slaveadd)
+static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed,
+ int slaveadd)
{
/* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */
writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) |
@@ -151,7 +152,7 @@
* I2C probe called by cmd_i2c when doing 'i2c probe'.
* Begin read, nak data byte, end.
*/
-int i2c_probe(u8 dev)
+static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev)
{
/* Attempt to read a byte */
setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
@@ -170,7 +171,8 @@
* I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c
* Begin write, send address byte(s), begin read, receive data bytes, end.
*/
-int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr,
+ int alen, u8 *data, int length)
{
u32 status;
u32 i = 0;
@@ -235,7 +237,8 @@
* I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
* Begin write, send address byte(s), send data bytes, end.
*/
-int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr,
+ int alen, u8 *data, int length)
{
u8 *cur_data = data;
@@ -275,16 +278,16 @@
return 0;
}
-int i2c_set_bus_num(unsigned int bus)
+static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap,
+ unsigned int speed)
{
- /* Only support bus 0 */
- if (bus > 0)
- return -1;
- return 0;
-}
+ if (speed != 1000000)
+ return -EINVAL;
-unsigned int i2c_get_bus_num(void)
-{
- /* Only support bus 0 */
return 0;
}
+
+U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read,
+ zynq_i2c_write, zynq_i2c_set_bus_speed,
+ CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE,
+ 0)