ARM: hisilicon: hikey: Fix eMMC with latest ATF & U-Boot
ATF can leave the MMC IP in a state where U-Boot mmc driver
can't enumerate the eMMC.
This patch provides a mmc0_reset_clk() function like we
already so do sd card controller which resets the IP
when entering U-Boot.
With this patch applied eMMC partitions are successfully
enumerated again.
=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device
=> mmc part
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000800 0x00000fff "vrl"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 496847ab-56a1-4cd5-a1ad-47f4acf055c9
2 0x00001000 0x000017ff "vrl_backup"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 61a36fc1-8efb-4899-84d8-b61642efa723
3 0x00001800 0x00001fff "mcuimage"
<snip>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
diff --git a/board/hisilicon/hikey/hikey.c b/board/hisilicon/hikey/hikey.c
index c513d0a..5357f87 100644
--- a/board/hisilicon/hikey/hikey.c
+++ b/board/hisilicon/hikey/hikey.c
@@ -295,13 +295,47 @@
data = readl(&peri_sc->rst0_stat);
} while (!(data & PERI_RST0_MMC1));
- /* unreset mmc0 clock domain */
+ /* unreset mmc1 clock domain */
writel(PERI_RST0_MMC1, &peri_sc->rst0_dis);
do {
data = readl(&peri_sc->rst0_stat);
} while (data & PERI_RST0_MMC1);
}
+static void mmc0_reset_clk(void)
+{
+ unsigned int data;
+
+ /* disable mmc0 bus clock */
+ hi6220_clk_disable(PERI_CLK0_MMC0, &peri_sc->clk0_dis);
+
+ /* enable mmc0 bus clock */
+ hi6220_clk_enable(PERI_CLK0_MMC0, &peri_sc->clk0_en);
+
+ /* reset mmc0 clock domain */
+ writel(PERI_RST0_MMC0, &peri_sc->rst0_en);
+
+ /* bypass mmc0 clock phase */
+ data = readl(&peri_sc->ctrl2);
+ data |= 3;
+ writel(data, &peri_sc->ctrl2);
+
+ /* disable low power */
+ data = readl(&peri_sc->ctrl13);
+ data |= 1 << 3;
+ writel(data, &peri_sc->ctrl13);
+ do {
+ data = readl(&peri_sc->rst0_stat);
+ } while (!(data & PERI_RST0_MMC0));
+
+ /* unreset mmc0 clock domain */
+ writel(PERI_RST0_MMC0, &peri_sc->rst0_dis);
+ do {
+ data = readl(&peri_sc->rst0_stat);
+ } while (data & PERI_RST0_MMC0);
+}
+
+
/* PMU SSI is the IP that maps the external PMU hi6553 registers as IO */
static void hi6220_pmussi_init(void)
{
@@ -349,7 +383,8 @@
#ifdef CONFIG_MMC_DW
- /* mmc0 clocks are already configured by ATF */
+ /* mmc0 pll is already configured by ATF */
+ mmc0_reset_clk();
ret = hi6220_pinmux_config(PERIPH_ID_SDMMC0);
if (ret)
printf("%s: Error configuring pinmux for eMMC (%d)\n"