ARM: uniphier: reserve memory for DRAM PHY training on PH1-LD20
The DRAM PHY layer on PH1-LD20 is able to calibrate PHY parameters
periodically. This compensates for the voltage and temperature
deviation and improves the PHY parameter adjustment. Instead, it
requires 64 byte scratch memory in each DRAM channel for the dynamic
training. The memory regions must be reserved in DT before jumping
to the kernel.
The scratch area can be anywhere in each DRAM channel, but the DRAM
init code in SPL currently assigns it at the end of each channel.
So, it makes sense to reserve the regions on run-time by U-Boot
instead of statically embedding it in the DT in Linux. Anyway,
a boot-loader should know much more about memory initialization
than the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 84cabb8..8a9cfcc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -827,6 +827,7 @@
select SPL
select OF_CONTROL
select SPL_OF_CONTROL
+ select OF_LIBFDT
select DM
select SPL_DM
select DM_GPIO
diff --git a/arch/arm/mach-uniphier/Kconfig b/arch/arm/mach-uniphier/Kconfig
index 89be0b3..e256eeb 100644
--- a/arch/arm/mach-uniphier/Kconfig
+++ b/arch/arm/mach-uniphier/Kconfig
@@ -40,6 +40,7 @@
config ARCH_UNIPHIER_LD20
bool "UniPhier PH1-LD20 SoC"
select ARCH_UNIPHIER_64BIT
+ select OF_BOARD_SETUP
endchoice
diff --git a/arch/arm/mach-uniphier/dram_init.c b/arch/arm/mach-uniphier/dram_init.c
index ef0e2e8..489366c 100644
--- a/arch/arm/mach-uniphier/dram_init.c
+++ b/arch/arm/mach-uniphier/dram_init.c
@@ -9,6 +9,9 @@
#include <fdtdec.h>
#include <linux/err.h>
+#include "init.h"
+#include "soc-info.h"
+
DECLARE_GLOBAL_DATA_PTR;
static const void *get_memory_reg_prop(const void *fdt, int *lenp)
@@ -80,4 +83,41 @@
i, (unsigned long)gd->bd->bi_dram[i].start,
(unsigned long)gd->bd->bi_dram[i].size);
}
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+/*
+ * The DRAM PHY requires 64 byte scratch area in each DRAM channel
+ * for its dynamic PHY training feature.
+ */
+int ft_board_setup(void *fdt, bd_t *bd)
+{
+ const struct uniphier_board_data *param;
+ unsigned long rsv_addr;
+ const unsigned long rsv_size = 64;
+ int ch, ret;
+
+ if (uniphier_get_soc_type() != SOC_UNIPHIER_LD20)
+ return 0;
+
+ param = uniphier_get_board_param();
+ if (!param) {
+ printf("failed to get board parameter\n");
+ return -ENODEV;
+ }
+
+ for (ch = 0; ch < param->dram_nr_ch; ch++) {
+ rsv_addr = param->dram_ch[ch].base + param->dram_ch[ch].size;
+ rsv_addr -= rsv_size;
+
+ ret = fdt_add_mem_rsv(fdt, rsv_addr, rsv_size);
+ if (ret)
+ return -ENOSPC;
+
+ printf(" Reserved memory region for DRAM PHY training: addr=%lx size=%lx\n",
+ rsv_addr, rsv_size);
+ }
+
+ return 0;
}
+#endif