drivers: add the support for Silicon Image SATA controller
Add the Silicon Image series PCI Express to
Serial ATA controller support, including Sil3132,
Sil3131 and Sil3124.
The SATA controller can be used to load kernel.
The features list:
- Supports 1-lane 2.5 Gbit/s PCI Express
- Supports one/two/four independent Serial ATA channels
- Supports Serial ATA Generation 2 transfer rate of 3.0 Gbit/s
- Supports LBA28 and LBA48
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Aaron Williams <Aaron.Williams@cavium.com>
Tested-by: Lan Chunhe <b25806@freescale.com>
diff --git a/drivers/block/sata_sil.h b/drivers/block/sata_sil.h
new file mode 100644
index 0000000..2dfd4a5
--- /dev/null
+++ b/drivers/block/sata_sil.h
@@ -0,0 +1,229 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Author: Tang Yuantian <b29983@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef SATA_SIL3132_H
+#define SATA_SIL3132_H
+
+#define READ_CMD 0
+#define WRITE_CMD 1
+
+extern block_dev_desc_t sata_dev_desc[CONFIG_SYS_SATA_MAX_DEVICE];
+
+/*
+ * SATA device driver struct for each dev
+ */
+struct sil_sata {
+ char name[12];
+ void *port; /* the port base address */
+ int lba48;
+ u16 pio;
+ u16 mwdma;
+ u16 udma;
+ pci_dev_t devno;
+ int wcache;
+ int flush;
+ int flush_ext;
+};
+
+/* sata info for each controller */
+struct sata_info {
+ ulong iobase[3];
+ pci_dev_t devno;
+ int portbase;
+ int maxport;
+};
+
+/*
+ * Scatter gather entry (SGE),MUST 8 bytes aligned
+ */
+struct sil_sge {
+ __le64 addr;
+ __le32 cnt;
+ __le32 flags;
+} __attribute__ ((aligned(8), packed));
+
+/*
+ * Port request block, MUST 8 bytes aligned
+ */
+struct sil_prb {
+ __le16 ctrl;
+ __le16 prot;
+ __le32 rx_cnt;
+ struct sata_fis_h2d fis;
+} __attribute__ ((aligned(8), packed));
+
+struct sil_cmd_block {
+ struct sil_prb prb;
+ struct sil_sge sge;
+};
+
+enum {
+ HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */
+ HOST_CTRL = 0x40,
+ HOST_IRQ_STAT = 0x44,
+ HOST_PHY_CFG = 0x48,
+ HOST_BIST_CTRL = 0x50,
+ HOST_BIST_PTRN = 0x54,
+ HOST_BIST_STAT = 0x58,
+ HOST_MEM_BIST_STAT = 0x5c,
+ HOST_FLASH_CMD = 0x70,
+ /* 8 bit regs */
+ HOST_FLASH_DATA = 0x74,
+ HOST_TRANSITION_DETECT = 0x75,
+ HOST_GPIO_CTRL = 0x76,
+ HOST_I2C_ADDR = 0x78, /* 32 bit */
+ HOST_I2C_DATA = 0x7c,
+ HOST_I2C_XFER_CNT = 0x7e,
+ HOST_I2C_CTRL = 0x7f,
+
+ /* HOST_SLOT_STAT bits */
+ HOST_SSTAT_ATTN = (1 << 31),
+
+ /* HOST_CTRL bits */
+ HOST_CTRL_M66EN = (1 << 16), /* M66EN PCI bus signal */
+ HOST_CTRL_TRDY = (1 << 17), /* latched PCI TRDY */
+ HOST_CTRL_STOP = (1 << 18), /* latched PCI STOP */
+ HOST_CTRL_DEVSEL = (1 << 19), /* latched PCI DEVSEL */
+ HOST_CTRL_REQ64 = (1 << 20), /* latched PCI REQ64 */
+ HOST_CTRL_GLOBAL_RST = (1 << 31), /* global reset */
+
+ /*
+ * Port registers
+ * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2)
+ */
+ PORT_REGS_SIZE = 0x2000,
+
+ PORT_LRAM = 0x0000, /* 31 LRAM slots and PMP regs */
+ PORT_LRAM_SLOT_SZ = 0x0080, /* 32 bytes PRB + 2 SGE, ACT... */
+
+ PORT_PMP = 0x0f80, /* 8 bytes PMP * 16 (128 bytes) */
+ PORT_PMP_STATUS = 0x0000, /* port device status offset */
+ PORT_PMP_QACTIVE = 0x0004, /* port device QActive offset */
+ PORT_PMP_SIZE = 0x0008, /* 8 bytes per PMP */
+
+ /* 32 bit regs */
+ PORT_CTRL_STAT = 0x1000, /* write: ctrl-set, read: stat */
+ PORT_CTRL_CLR = 0x1004, /* write: ctrl-clear */
+ PORT_IRQ_STAT = 0x1008, /* high: status, low: interrupt */
+ PORT_IRQ_ENABLE_SET = 0x1010, /* write: enable-set */
+ PORT_IRQ_ENABLE_CLR = 0x1014, /* write: enable-clear */
+ PORT_ACTIVATE_UPPER_ADDR = 0x101c,
+ PORT_EXEC_FIFO = 0x1020, /* command execution fifo */
+ PORT_CMD_ERR = 0x1024, /* command error number */
+ PORT_FIS_CFG = 0x1028,
+ PORT_FIFO_THRES = 0x102c,
+
+ /* 16 bit regs */
+ PORT_DECODE_ERR_CNT = 0x1040,
+ PORT_DECODE_ERR_THRESH = 0x1042,
+ PORT_CRC_ERR_CNT = 0x1044,
+ PORT_CRC_ERR_THRESH = 0x1046,
+ PORT_HSHK_ERR_CNT = 0x1048,
+ PORT_HSHK_ERR_THRESH = 0x104a,
+
+ /* 32 bit regs */
+ PORT_PHY_CFG = 0x1050,
+ PORT_SLOT_STAT = 0x1800,
+ PORT_CMD_ACTIVATE = 0x1c00, /* 64 bit cmd activate * 31 */
+ PORT_CONTEXT = 0x1e04,
+ PORT_EXEC_DIAG = 0x1e00, /* 32bit exec diag * 16 */
+ PORT_PSD_DIAG = 0x1e40, /* 32bit psd diag * 16 */
+ PORT_SCONTROL = 0x1f00,
+ PORT_SSTATUS = 0x1f04,
+ PORT_SERROR = 0x1f08,
+ PORT_SACTIVE = 0x1f0c,
+
+ /* PORT_CTRL_STAT bits */
+ PORT_CS_PORT_RST = (1 << 0), /* port reset */
+ PORT_CS_DEV_RST = (1 << 1), /* device reset */
+ PORT_CS_INIT = (1 << 2), /* port initialize */
+ PORT_CS_IRQ_WOC = (1 << 3), /* interrupt write one to clear */
+ PORT_CS_CDB16 = (1 << 5), /* 0=12b cdb, 1=16b cdb */
+ PORT_CS_PMP_RESUME = (1 << 6), /* PMP resume */
+ PORT_CS_32BIT_ACTV = (1 << 10), /* 32-bit activation */
+ PORT_CS_PMP_EN = (1 << 13), /* port multiplier enable */
+ PORT_CS_RDY = (1 << 31), /* port ready to accept commands */
+
+ /* PORT_IRQ_STAT/ENABLE_SET/CLR */
+ /* bits[11:0] are masked */
+ PORT_IRQ_COMPLETE = (1 << 0), /* command(s) completed */
+ PORT_IRQ_ERROR = (1 << 1), /* command execution error */
+ PORT_IRQ_PORTRDY_CHG = (1 << 2), /* port ready change */
+ PORT_IRQ_PWR_CHG = (1 << 3), /* power management change */
+ PORT_IRQ_PHYRDY_CHG = (1 << 4), /* PHY ready change */
+ PORT_IRQ_COMWAKE = (1 << 5), /* COMWAKE received */
+ PORT_IRQ_UNK_FIS = (1 << 6), /* unknown FIS received */
+ PORT_IRQ_DEV_XCHG = (1 << 7), /* device exchanged */
+ PORT_IRQ_8B10B = (1 << 8), /* 8b/10b decode error threshold */
+ PORT_IRQ_CRC = (1 << 9), /* CRC error threshold */
+ PORT_IRQ_HANDSHAKE = (1 << 10), /* handshake error threshold */
+ PORT_IRQ_SDB_NOTIFY = (1 << 11), /* SDB notify received */
+
+ DEF_PORT_IRQ = PORT_IRQ_COMPLETE | PORT_IRQ_ERROR |
+ PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG |
+ PORT_IRQ_UNK_FIS | PORT_IRQ_SDB_NOTIFY,
+
+ /* bits[27:16] are unmasked (raw) */
+ PORT_IRQ_RAW_SHIFT = 16,
+ PORT_IRQ_MASKED_MASK = 0x7ff,
+ PORT_IRQ_RAW_MASK = (0x7ff << PORT_IRQ_RAW_SHIFT),
+
+ /* ENABLE_SET/CLR specific, intr steering - 2 bit field */
+ PORT_IRQ_STEER_SHIFT = 30,
+ PORT_IRQ_STEER_MASK = (3 << PORT_IRQ_STEER_SHIFT),
+
+ /* PORT_CMD_ERR constants */
+ PORT_CERR_DEV = 1, /* Error bit in D2H Register FIS */
+ PORT_CERR_SDB = 2, /* Error bit in SDB FIS */
+ PORT_CERR_DATA = 3, /* Error in data FIS not detected by dev */
+ PORT_CERR_SEND = 4, /* Initial cmd FIS transmission failure */
+ PORT_CERR_INCONSISTENT = 5, /* Protocol mismatch */
+ PORT_CERR_DIRECTION = 6, /* Data direction mismatch */
+ PORT_CERR_UNDERRUN = 7, /* Ran out of SGEs while writing */
+ PORT_CERR_OVERRUN = 8, /* Ran out of SGEs while reading */
+
+ /* bits of PRB control field */
+ PRB_CTRL_PROTOCOL = (1 << 0), /* override def. ATA protocol */
+ PRB_CTRL_PACKET_READ = (1 << 4), /* PACKET cmd read */
+ PRB_CTRL_PACKET_WRITE = (1 << 5), /* PACKET cmd write */
+ PRB_CTRL_NIEN = (1 << 6), /* Mask completion irq */
+ PRB_CTRL_SRST = (1 << 7), /* Soft reset request (ign BSY?) */
+
+ /* PRB protocol field */
+ PRB_PROT_PACKET = (1 << 0),
+ PRB_PROT_TCQ = (1 << 1),
+ PRB_PROT_NCQ = (1 << 2),
+ PRB_PROT_READ = (1 << 3),
+ PRB_PROT_WRITE = (1 << 4),
+ PRB_PROT_TRANSPARENT = (1 << 5),
+
+ /*
+ * Other constants
+ */
+ SGE_TRM = (1 << 31), /* Last SGE in chain */
+ SGE_LNK = (1 << 30), /* linked list
+ Points to SGT, not SGE */
+ SGE_DRD = (1 << 29), /* discard data read (/dev/null)
+ data address ignored */
+
+ CMD_ERR = 0x21,
+};
+
+#endif