// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2019 Kontron Electronics GmbH
 */

#include <asm/arch/imx-regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/mach-imx/boot_mode.h>
#include <efi.h>
#include <efi_loader.h>
#include <env_internal.h>
#include <fdt_support.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <net.h>

DECLARE_GLOBAL_DATA_PTR;

#if CONFIG_IS_ENABLED(EFI_HAVE_CAPSULE_SUPPORT)
struct efi_fw_image fw_images[] = {
	{
		.image_type_id = KONTRON_SL_MX8MM_FIT_IMAGE_GUID,
		.fw_name = u"KONTROL-SL-MX8MM-UBOOT",
		.image_index = 1,
	},
};

struct efi_capsule_update_info update_info = {
	.dfu_string = "sf 0:0=flash-bin raw 0x400 0x1f0000",
	.images = fw_images,
};

u8 num_image_type_guids = ARRAY_SIZE(fw_images);
#endif /* EFI_HAVE_CAPSULE_SUPPORT */

int board_phys_sdram_size(phys_size_t *size)
{
	u32 ddr_size = readl(M4_BOOTROM_BASE_ADDR);

	if (ddr_size == 4) {
		*size = 0x100000000;
	} else if (ddr_size == 3) {
		*size = 0xc0000000;
	} else if (ddr_size == 2) {
		*size = 0x80000000;
	} else if (ddr_size == 1) {
		*size = 0x40000000;
	} else {
		printf("Unknown DDR type!!!\n");
		*size = 0x40000000;
	}

	return 0;
}

/*
 * If the SoM is mounted on a baseboard with a USB ethernet controller,
 * there might be an additional MAC address programmed to the MAC OTP fuses.
 * Although the i.MX8MM has only one MAC, the MAC0, MAC1 and MAC2 registers
 * in the OTP fuses can still be used to store two separate addresses.
 * Try to read the secondary address from MAC1 and MAC2 and adjust the
 * devicetree so Linux can pick up the MAC address.
 */
int fdt_set_usb_eth_addr(void *blob)
{
	u32 value = readl(OCOTP_BASE_ADDR + 0x660);
	unsigned char mac[6];
	int node, ret;

	mac[0] = value >> 24;
	mac[1] = value >> 16;
	mac[2] = value >> 8;
	mac[3] = value;

	value = readl(OCOTP_BASE_ADDR + 0x650);
	mac[4] = value >> 24;
	mac[5] = value >> 16;

	node = fdt_path_offset(blob, fdt_get_alias(blob, "ethernet1"));
	if (node < 0) {
		/*
		 * There is no node for the USB ethernet in the devicetree. Just skip.
		 */
		return 0;
	}

	if (is_zero_ethaddr(mac)) {
		printf("\nNo MAC address for USB ethernet set in OTP fuses!\n");
		return 0;
	}

	if (!is_valid_ethaddr(mac)) {
		printf("\nInvalid MAC address for USB ethernet set in OTP fuses!\n");
		return -EINVAL;
	}

	ret = fdt_setprop(blob, node, "local-mac-address", &mac, 6);
	if (ret)
		ret = fdt_setprop(blob, node, "mac-address", &mac, 6);

	if (ret)
		printf("\nMissing mac-address or local-mac-address property in dt, skip setting MAC address for USB ethernet\n");

	return 0;
}

int ft_board_setup(void *blob, struct bd_info *bd)
{
	int ret = fdt_set_usb_eth_addr(blob);

	if (ret)
		return ret;

	return fdt_fixup_memory(blob, PHYS_SDRAM, gd->ram_size);
}

int board_init(void)
{
	return 0;
}

int board_late_init(void)
{
	if (!fdt_node_check_compatible(gd->fdt_blob, 0, "kontron,imx8mm-n802x-som") ||
	    !fdt_node_check_compatible(gd->fdt_blob, 0, "kontron,imx8mm-osm-s")) {
		env_set("som_type", "osm-s");
		env_set("touch_rst_gpio", "111");
	} else {
		env_set("som_type", "sl");
		env_set("touch_rst_gpio", "87");
	}

	return 0;
}

enum env_location env_get_location(enum env_operation op, int prio)
{
	enum boot_device boot_dev = get_boot_device();

	if (prio)
		return ENVL_UNKNOWN;

	/*
	 * Make sure that the environment is loaded from
	 * the MMC if we are running from SD card or eMMC.
	 */
	if (CONFIG_IS_ENABLED(ENV_IS_IN_MMC) &&
	    (boot_dev == SD1_BOOT || boot_dev == SD2_BOOT))
		return ENVL_MMC;

	if (CONFIG_IS_ENABLED(ENV_IS_IN_SPI_FLASH))
		return ENVL_SPI_FLASH;

	return ENVL_NOWHERE;
}

#if defined(CONFIG_ENV_IS_IN_MMC)
int board_mmc_get_env_dev(int devno)
{
	return devno;
}
#endif