diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
index 7c38264..0bc031f 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -49,7 +49,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi Zero";
@@ -58,6 +57,7 @@
 	aliases {
 		serial0 = &uart0;
 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &xr819;
 	};
 
@@ -92,9 +92,14 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -109,8 +114,7 @@
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -130,17 +134,56 @@
 	};
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
+&spi0 {
+	/* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+	status = "disabled";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
 &usbphy {
-	/* USB VBUS is always on */
+	/*
+	 * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+	 * power up the board; when it's used as OTG port, this VBUS is
+	 * always off even if the board is powered via GPIO pins.
+	 */
 	status = "okay";
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 };
diff --git a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
index 124ec47..30540dc 100644
--- a/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -46,13 +46,13 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Banana Pi BPI-M2-Plus";
 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -61,10 +61,20 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pwr_led_bpi_m2p>;
 
 		pwr_led {
 			label = "bananapi-m2-plus:red:pwr";
@@ -76,7 +86,6 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_bpi_m2p>;
 
 		sw4 {
 			label = "power";
@@ -85,14 +94,27 @@
 		};
 	};
 
+	reg_gmac_3v3: gmac-3v3 {
+		      compatible = "regulator-fixed";
+		      regulator-name = "gmac-3v3";
+		      regulator-min-microvolt = <3300000>;
+		      regulator-max-microvolt = <3300000>;
+		      startup-delay-us = <100000>;
+		      enable-active-high;
+		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_bpi_m2p>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -105,6 +127,33 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -114,8 +163,7 @@
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -127,7 +175,7 @@
 	non-removable;
 	status = "okay";
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
@@ -158,27 +206,9 @@
 	status = "okay";
 };
 
-&r_pio {
-	pwr_led_bpi_m2p: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	sw_r_bpi_m2p: key_pins@0 {
-		allwinner,pins = "PL3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	wifi_en_bpi_m2p: wifi_en_pin {
-		allwinner,pins = "PL7";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
+&reg_usb0_vbus {
+	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+	status = "okay";
 };
 
 &uart0 {
@@ -199,6 +229,8 @@
 };
 
 &usbphy {
-	/* USB VBUS is on as long as VCC-IO is on */
+	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* USB host VBUS is on as long as VCC-IO is on */
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
index 50f2fb3..a8b2f0f 100644
--- a/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
+++ b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
@@ -1,6 +1,7 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
  */
 
 /dts-v1/;
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
index 8ddd1b2..65cba10 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -45,6 +45,28 @@
 / {
 	model = "FriendlyArm NanoPi M1 Plus";
 	compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial1 = &uart3;
+		ethernet0 = &emac;
+		ethernet1 = &sdio_wifi;
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
 };
 
 &ehci1 {
@@ -53,8 +75,58 @@
 
 &ehci2 {
 	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: sdio_wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
 };
 
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -62,3 +134,9 @@
 &ohci2 {
 	status = "okay";
 };
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
index ec63d10..9412668 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
@@ -45,8 +45,27 @@
 / {
 	model = "FriendlyArm NanoPi M1";
 	compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -55,6 +74,29 @@
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
index 4208a6a..6246d3e 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
@@ -45,7 +45,6 @@
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "FriendlyARM NanoPi NEO Air";
@@ -73,16 +72,37 @@
 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
 		};
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
 };
 
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/dts/sun8i-h3-nanopi-neo.dts
index 78f6c24..9f33f6f 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo.dts
@@ -47,9 +47,26 @@
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &emac {
 	phy-handle = <&int_mii_phy>;
 	phy-mode = "mii";
 	allwinner,leds-active-low;
 	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 };
diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi b/arch/arm/dts/sun8i-h3-nanopi.dtsi
index 8b1b250..f110ee3 100644
--- a/arch/arm/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi
@@ -81,7 +81,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&sw_r_npi>;
 
-		k1@0 {
+		k1 {
 			label = "k1";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -95,8 +95,7 @@
 
 &mmc0 {
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 	vmmc-supply = <&reg_vcc3v3>;
 };
@@ -106,19 +105,19 @@
 };
 
 &pio {
-	leds_npi: led_pins@0 {
+	leds_npi: led_pins {
 		pins = "PA10";
 		function = "gpio_out";
 	};
 };
 
 &r_pio {
-	leds_r_npi: led_pins@0 {
+	leds_r_npi: led_pins {
 		pins = "PL10";
 		function = "gpio_out";
 	};
 
-	sw_r_npi: key_pins@0 {
+	sw_r_npi: key_pins {
 		pins = "PL3";
 		function = "gpio_in";
 	};
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index b8320d2..f1fc6bd 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi 2";
@@ -63,6 +62,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -106,6 +116,19 @@
 	};
 };
 
+&codec {
+	allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+	allwinner,audio-routing =
+		"Speaker", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -117,6 +140,16 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -126,8 +159,7 @@
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -148,34 +180,26 @@
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_opc: led_pins {
+		pins = "PA15";
+		function = "gpio_out";
 	};
 };
 
 &r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_r_opc: led_pins {
+		pins = "PL10";
+		function = "gpio_out";
 	};
 
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3", "PL4";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	sw_r_opc: key_pins {
+		pins = "PL3", "PL4";
+		function = "gpio_in";
 	};
 
-	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
-		allwinner,pins = "PL7";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
+		pins = "PL7";
+		function = "gpio_out";
 	};
 };
 
@@ -190,8 +214,22 @@
 	status = "okay";
 };
 
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG13";
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
 };
 
 &usbphy {
diff --git a/arch/arm/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
index b9b2b78..476ae8e 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi Lite";
@@ -62,6 +61,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -92,6 +102,10 @@
 	};
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -100,6 +114,16 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -109,8 +133,7 @@
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -138,27 +161,21 @@
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_opc: led_pins {
+		pins = "PA15";
+		function = "gpio_out";
 	};
 };
 
 &r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_r_opc: led_pins {
+		pins = "PL10";
+		function = "gpio_out";
 	};
 
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	sw_r_opc: key_pins {
+		pins = "PL3";
+		function = "gpio_in";
 	};
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-one.dts b/arch/arm/dts/sun8i-h3-orangepi-one.dts
index 16e602b..245fd65 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-one.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi One";
@@ -61,6 +60,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -89,8 +99,37 @@
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		enable-active-high;
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
 };
 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -102,50 +141,87 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_opc: led_pins {
+		pins = "PA15";
+		function = "gpio_out";
 	};
 };
 
 &r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_r_opc: led_pins {
+		pins = "PL10";
+		function = "gpio_out";
 	};
 
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	sw_r_opc: key_pins {
+		pins = "PL3";
+		function = "gpio_in";
 	};
 };
 
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
-	/* USB VBUS is always on */
+	/* USB Type-A port's VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts
index 4653cac..71fb732 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts
@@ -53,6 +53,11 @@
 	};
 };
 
+&emac {
+	/* LEDs changed to active high on the plus */
+	/delete-property/ allwinner,leds-active-low;
+};
+
 &mmc1 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
@@ -80,7 +85,7 @@
 
 &mmc2_8bit_pins {
 	/* Increase drive strength for DDR modes */
-	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+	drive-strength = <40>;
 	/* eMMC is missing pull-ups */
-	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	bias-pull-up;
 };
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
index 3ae8f7c..4624033 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi PC";
@@ -61,6 +60,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -91,6 +101,26 @@
 	};
 };
 
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -103,6 +133,23 @@
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -112,8 +159,11 @@
 &mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&ohci0 {
 	status = "okay";
 };
 
@@ -130,44 +180,85 @@
 };
 
 &pio {
-	leds_opc: led_pins@0 {
-		allwinner,pins = "PA15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_opc: led_pins {
+		pins = "PA15";
+		function = "gpio_out";
+	};
+};
+
+&r_i2c {
+	status = "okay";
+
+	reg_vdd_cpux: regulator@65 {
+		compatible = "silergy,sy8106a";
+		reg = <0x65>;
+		regulator-name = "vdd-cpux";
+		silergy,fixed-microvolt = <1200000>;
+		/*
+		 * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
+		 * however both the Armbian DVFS table and the official one
+		 * have operating points with voltage under 1.1V, and both
+		 * DVFS table are known to work properly at the lowest
+		 * operating point.
+		 *
+		 * Use 1.0V as the minimum voltage instead.
+		 */
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-boot-on;
+		regulator-always-on;
 	};
 };
 
 &r_pio {
-	leds_r_opc: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	leds_r_opc: led_pins {
+		pins = "PL10";
+		function = "gpio_out";
 	};
 
-	sw_r_opc: key_pins@0 {
-		allwinner,pins = "PL3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	sw_r_opc: key_pins {
+		pins = "PL3";
+		function = "gpio_in";
 	};
 };
 
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
-&usbphy {
-	/* USB VBUS is always on */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "otg";
 	status = "okay";
 };
 
-&emac {
-	phy-handle = <&int_mii_phy>;
-	phy-mode = "mii";
-	allwinner,leds-active-low;
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* VBUS on USB host ports are always on */
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
index 136e441..b403e5d 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
@@ -47,10 +47,12 @@
 	model = "Xunlong Orange Pi Plus / Plus 2";
 	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
 
+	aliases {
+		ethernet0 = &emac;
+	};
+
 	reg_gmac_3v3: gmac-3v3 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&gmac_power_pin_orangepi>;
 		regulator-name = "gmac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -77,11 +79,13 @@
 };
 
 &emac {
-	/* The Orange Pi Plus uses an external phy */
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
+
+	status = "okay";
 };
 
 &external_mdio {
@@ -103,24 +107,15 @@
 
 &mmc2_8bit_pins {
 	/* Increase drive strength for DDR modes */
-	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+	drive-strength = <40>;
 	/* eMMC is missing pull-ups */
-	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	bias-pull-up;
 };
 
 &pio {
-	gmac_power_pin_orangepi: gmac_power_pin@0 {
-		allwinner,pins = "PD6";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	usb3_vbus_pin_a: usb3_vbus_pin@0 {
-		allwinner,pins = "PG11";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	usb3_vbus_pin_a: usb3_vbus_pin {
+		pins = "PG11";
+		function = "gpio_out";
 	};
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/dts/sun8i-h3-orangepi-plus2e.dts
index 51aaf49..6dbf7b2 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-plus2e.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-plus2e.dts
@@ -53,24 +53,22 @@
 
 	reg_gmac_3v3: gmac-3v3 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&gmac_power_pin_orangepi>;
 		regulator-name = "gmac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		startup-delay-us = <100000>;
 		enable-active-high;
-		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
 	};
 };
 
 &emac {
-	/* The Orange Pi Plus 2E uses an external gbit phy */
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
 	phy-mode = "rgmii";
+	status = "okay";
 };
 
 &external_mdio {
@@ -79,12 +77,3 @@
 		reg = <1>;
 	};
 };
-
-&pio {
-	gmac_power_pin_orangepi: gmac_power_pin@0 {
-		allwinner,pins = "PD6";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};