diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ea420db..b415613 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1104,6 +1104,7 @@
 	imx8mp-dhcom-som-overlay-eth1xfast.dtbo \
 	imx8mp-dhcom-som-overlay-eth2xfast.dtbo \
 	imx8mp-dhcom-pdk-overlay-eth2xfast.dtbo \
+	imx8mp-debix-model-a.dtb \
 	imx8mp-dhcom-pdk2.dtb \
 	imx8mp-dhcom-pdk3.dtb \
 	imx8mp-dhcom-pdk3-overlay-rev100.dtbo \
diff --git a/arch/arm/dts/imx8mp-debix-model-a-u-boot.dtsi b/arch/arm/dts/imx8mp-debix-model-a-u-boot.dtsi
new file mode 100644
index 0000000..33bd89a
--- /dev/null
+++ b/arch/arm/dts/imx8mp-debix-model-a-u-boot.dtsi
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019, 2021 NXP
+ * Copyright 2023 Gilles Talis <gilles.talis@gmail.com>
+ */
+
+#include "imx8mp-u-boot.dtsi"
+
+/ {
+	wdt-reboot {
+		compatible = "wdt-reboot";
+		wdt = <&wdog1>;
+		bootph-pre-ram;
+	};
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+};
+
+&crypto {
+	bootph-pre-ram;
+};
+
+&ethphy0 {
+	reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <15000>;
+	reset-post-delay-us = <100000>;
+};
+
+&fec {
+	phy-reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <15>;
+	phy-reset-post-delay = <100>;
+};
+
+&gpio1 {
+	bootph-pre-ram;
+};
+
+&gpio2 {
+	bootph-pre-ram;
+};
+
+&gpio3 {
+	bootph-pre-ram;
+};
+
+&gpio4 {
+	bootph-pre-ram;
+};
+
+&gpio5 {
+	bootph-pre-ram;
+};
+
+&i2c1 {
+	bootph-pre-ram;
+};
+
+&pinctrl_i2c1 {
+	bootph-pre-ram;
+};
+
+&pinctrl_pmic {
+	bootph-pre-ram;
+};
+
+&pinctrl_uart2 {
+	bootph-pre-ram;
+};
+
+&pinctrl_usdhc2_gpio {
+	bootph-pre-ram;
+};
+
+&pinctrl_usdhc2 {
+	bootph-pre-ram;
+};
+
+&pinctrl_usdhc3 {
+	bootph-pre-ram;
+};
+
+&pinctrl_wdog {
+	bootph-pre-ram;
+};
+
+&pmic {
+	bootph-pre-ram;
+
+	regulators {
+		bootph-pre-ram;
+	};
+};
+
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
+&reg_usdhc2_vmmc {
+	bootph-pre-ram;
+};
+
+&uart2 {
+	bootph-pre-ram;
+};
+
+&sec_jr0 {
+	bootph-pre-ram;
+};
+
+&sec_jr1 {
+	bootph-pre-ram;
+};
+
+&sec_jr2 {
+	bootph-pre-ram;
+};
+
+&usdhc1 {
+	bootph-pre-ram;
+};
+
+&usdhc2 {
+	bootph-pre-ram;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+};
+
+&usdhc3 {
+	bootph-pre-ram;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+};
+
+&wdog1 {
+	bootph-pre-ram;
+};
diff --git a/arch/arm/dts/imx8mp-debix-model-a.dts b/arch/arm/dts/imx8mp-debix-model-a.dts
new file mode 100644
index 0000000..58dae61
--- /dev/null
+++ b/arch/arm/dts/imx8mp-debix-model-a.dts
@@ -0,0 +1,507 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright 2022 Ideas on Board Oy
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/usb/pd.h>
+
+#include "imx8mp.dtsi"
+
+/ {
+	model = "Polyhex Debix Model A i.MX8MPlus board";
+	compatible = "polyhex,imx8mp-debix-model-a", "polyhex,imx8mp-debix", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 { /* RTL8211E */
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <20>;
+			reset-deassert-us = <200000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic: pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck2: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			buck4: BUCK4{
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: BUCK5{
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6: BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+	};
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c6>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart2 {
+	/* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+/* SD Card */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN			0x1f
+			MX8MP_IOMUXC_SAI1_RXC__ENET1_1588_EVENT0_OUT			0x1f
+			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18				0x19
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC				0x3
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO				0x3
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0				0x91
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1				0x91
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2				0x91
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3				0x91
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC				0x91
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL			0x91
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0				0x1f
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1				0x1f
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2				0x1f
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3				0x1f
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL			0x1f
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC				0x1f
+			MX8MP_IOMUXC_SAI1_RXD1__ENET1_1588_EVENT1_OUT			0x1f
+			MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN			0x1f
+			MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19				0x19
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16				0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL					0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA					0x400001c2
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL					0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA					0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL					0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA					0x400001c2
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL					0x400001c3
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_i2c6: i2c6grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL				0x400001c3
+			MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03				0x41
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19				0x41
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11				0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX				0x14f
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX				0x14f
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX				0x49
+			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX				0x49
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX				0x49
+			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX				0x49
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12				0x1c4
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B				0xc6
+		>;
+	};
+};
+
diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
index 3d62d70..b802d5c 100644
--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
@@ -199,6 +199,13 @@
 	select ARCH_MISC_INIT
 	select SPL_CRYPTO if SPL
 
+config TARGET_IMX8MP_DEBIX_MODEL_A
+	bool "Polyhex i.MX8M Plus Debix Model A SBC"
+	select BINMAN
+	select IMX8MP
+	select IMX8M_LPDDR4
+	select SUPPORT_SPL
+
 config TARGET_IMX8MP_DH_DHCOM_PDK2
 	bool "DH electronics DHCOM Premium Developer Kit (2) i.MX8M Plus"
 	select BINMAN
@@ -384,6 +391,7 @@
 source "board/mntre/imx8mq_reform2/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mp/Kconfig"
+source "board/polyhex/imx8mp_debix_model_a/Kconfig"
 source "board/purism/librem5/Kconfig"
 source "board/ronetix/imx8mq-cm/Kconfig"
 source "board/technexion/pico-imx8mq/Kconfig"