sunxi: binman: Move BL31 and SCP firmware addresses to Kconfig
This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
diff --git a/arch/arm/dts/sunxi-u-boot.dtsi b/arch/arm/dts/sunxi-u-boot.dtsi
index a0c8abb..7a8764e 100644
--- a/arch/arm/dts/sunxi-u-boot.dtsi
+++ b/arch/arm/dts/sunxi-u-boot.dtsi
@@ -1,15 +1,5 @@
#include <config.h>
-#ifdef CONFIG_MACH_SUN50I_H6
-#define BL31_ADDR 0x104000
-#define SCP_ADDR 0x114000
-#elif defined(CONFIG_MACH_SUN50I_H616)
-#define BL31_ADDR 0x40000000
-#else
-#define BL31_ADDR 0x44000
-#define SCP_ADDR 0x50000
-#endif
-
/ {
aliases {
mmc0 = &mmc0;
@@ -69,8 +59,8 @@
os = "arm-trusted-firmware";
arch = "arm64";
compression = "none";
- load = <BL31_ADDR>;
- entry = <BL31_ADDR>;
+ load = <CONFIG_SUNXI_BL31_BASE>;
+ entry = <CONFIG_SUNXI_BL31_BASE>;
atf-bl31 {
filename = "bl31.bin";
@@ -78,13 +68,13 @@
};
};
-#ifdef SCP_ADDR
+#if CONFIG_SUNXI_SCP_BASE
scp {
description = "SCP firmware";
type = "firmware";
arch = "or1k";
compression = "none";
- load = <SCP_ADDR>;
+ load = <CONFIG_SUNXI_SCP_BASE>;
scp {
filename = "scp.bin";
@@ -106,10 +96,10 @@
@config-SEQ {
description = "NAME";
firmware = "atf";
-#ifndef SCP_ADDR
- loadables = "uboot";
-#else
+#if CONFIG_SUNXI_SCP_BASE
loadables = "scp", "uboot";
+#else
+ loadables = "uboot";
#endif
fdt = "fdt-SEQ";
};
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 421a48b..fe89aec 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -161,6 +161,23 @@
for all other SoCs, so the content of the SRAM_VER_REG becomes
irrelevant there, and we can use the same code.
+config SUNXI_BL31_BASE
+ hex
+ default 0x00044000 if MACH_SUN50I || MACH_SUN50I_H5
+ default 0x00104000 if MACH_SUN50I_H6
+ default 0x40000000 if MACH_SUN50I_H616
+ default 0x0
+ help
+ Address where BL31 (TF-A) is loaded, or zero if BL31 is not used.
+
+config SUNXI_SCP_BASE
+ hex
+ default 0x00050000 if MACH_SUN50I || MACH_SUN50I_H5
+ default 0x00114000 if MACH_SUN50I_H6
+ default 0x0
+ help
+ Address where SCP firmware is loaded, or zero if it is not used.
+
config SUNXI_A64_TIMER_ERRATUM
bool