keymile: Factor out common includes again
Not that the Kconfig conversion of a lot of variables is done, we can
factor out the common include files for the keymile boards again (which
now contain hardly any #ifdef logic at all).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
diff --git a/include/configs/km/km-mpc8309.h b/include/configs/km/km-mpc8309.h
new file mode 100644
index 0000000..e89b7af
--- /dev/null
+++ b/include/configs/km/km-mpc8309.h
@@ -0,0 +1,137 @@
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 66000000
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define CONFIG_83XX_PCICLK 66000000
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0 \
+ | SICR_1_UART1_UART1RTS \
+ | SICR_1_I2C_CKSTOP \
+ | SICR_1_IRQ_A_IRQ \
+ | SICR_1_IRQ_B_IRQ \
+ | SICR_1_GPIO_A_GPIO \
+ | SICR_1_GPIO_B_GPIO \
+ | SICR_1_GPIO_C_GPIO \
+ | SICR_1_GPIO_D_GPIO \
+ | SICR_1_GPIO_E_GPIO \
+ | SICR_1_GPIO_F_GPIO \
+ | SICR_1_USB_A_UART2S \
+ | SICR_1_USB_B_UART2RTS \
+ | SICR_1_FEC1_FEC1 \
+ | SICR_1_FEC2_FEC2 \
+ )
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0 \
+ | SICR_2_FEC3_FEC3 \
+ | SICR_2_HDLC1_A_HDLC1 \
+ | SICR_2_ELBC_A_LA \
+ | SICR_2_ELBC_B_LCLK \
+ | SICR_2_HDLC2_A_HDLC2 \
+ | SICR_2_USB_D_GPIO \
+ | SICR_2_PCI_PCI \
+ | SICR_2_HDLC1_B_HDLC1 \
+ | SICR_2_HDLC1_C_HDLC1 \
+ | SICR_2_HDLC2_B_GPIO \
+ | SICR_2_HDLC2_C_HDLC2 \
+ | SICR_2_QUIESCE_B \
+ )
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1 0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_RD_NEVER | \
+ CSCONFIG_ODT_WR_ONLY_CURRENT | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
diff --git a/include/configs/km/km-mpc832x.h b/include/configs/km/km-mpc832x.h
new file mode 100644
index 0000000..3c2173d
--- /dev/null
+++ b/include/configs/km/km-mpc832x.h
@@ -0,0 +1,91 @@
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE /* Has QE */
+#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 66000000
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define CONFIG_83XX_PCICLK 66000000
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH1 /* GETH1 */
+#define UEC_VERBOSE_DEBUG 1
+
+#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR 0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_WR_CFG | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h
new file mode 100644
index 0000000..8f26e05
--- /dev/null
+++ b/include/configs/km/km-mpc8360.h
@@ -0,0 +1,91 @@
+/* KMBEC FPGA (PRIO) */
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 64
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE /* Has QE */
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH1 /* GETH1 */
+#define UEC_VERBOSE_DEBUG 1
+
+#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR 0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+
+/*
+ * System IO Setup
+ */
+#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI)
+
+/**
+ * DDR RAM settings
+ */
+#define CONFIG_SYS_DDR_SDRAM_CFG (\
+ SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+
+#define CONFIG_SYS_DDR_CLK_CNTL (\
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CONFIG_SYS_DDR_INTERVAL (\
+ (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_Q_DRN)
+#define CONFIG_SYS_DDR_MODE 0x47860452
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 (\
+ (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 (\
+ (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+
+/*
+ * PAXE on the local bus CS3
+ */
+#define CONFIG_SYS_PAXE_BASE 0xA0000000
+#define CONFIG_SYS_PAXE_SIZE 256
diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h
new file mode 100644
index 0000000..455e523
--- /dev/null
+++ b/include/configs/km/km-mpc83xx.h
@@ -0,0 +1,160 @@
+/*
+ * Internal Definitions
+ */
+#define BOOTFLASH_START 0xF0000000
+
+#define CONFIG_KM_CONSOLE_TTY "ttyS0"
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
+
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_FLASH_BASE 0xF0000000
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+/* Reserve 768 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus Machine PortSz Size Device
+ * ---- --- ------- ------ ----- ------
+ * 0 Local GPCM 16 bit 256MB FLASH
+ * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
+ *
+ */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES 4
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 200000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+ {1, {I2C_NULL_HOP} } }
+
+#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+
+/*
+ * Environment
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#ifndef CONFIG_ENV_ADDR
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#endif
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#ifndef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
+#endif
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+#else /* CFG_SYS_RAMBOOT */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x2000
+#endif /* CFG_SYS_RAMBOOT */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ CONFIG_KM_DEF_ARCH \
+ "newenv=" \
+ "prot off " __stringify(CONFIG_ENV_ADDR) " +0x40000 && " \
+ "era " __stringify(CONFIG_ENV_ADDR) " +0x40000\0" \
+ "unlock=yes\0" \
+ ""
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME "UEC0"
diff --git a/include/configs/kmcoge5ne.h b/include/configs/kmcoge5ne.h
index 847996f..fc78b27c 100644
--- a/include/configs/kmcoge5ne.h
+++ b/include/configs/kmcoge5ne.h
@@ -8,10 +8,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/* KMBEC FPGA (PRIO) */
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 64
-
#define CONFIG_HOSTNAME "kmcoge5ne"
#define CONFIG_KM_BOARD_NAME "kmcoge5ne"
#define CONFIG_KM_DEF_NETDEV "netdev=eth1\0"
@@ -24,14 +20,11 @@
#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0"
#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
/*
* System Clock Setup
@@ -40,202 +33,7 @@
#define CONFIG_SYS_CLK_FREQ 66000000
#define CONFIG_83XX_PCICLK 66000000
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Setup
- */
-#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI)
-
/**
- * DDR RAM settings
- */
-#define CONFIG_SYS_DDR_SDRAM_CFG (\
- SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-
-/**
* KMCOGE5NE has 512 MB RAM
*/
#define CONFIG_SYS_DDR_CS0_CONFIG (\
@@ -246,68 +44,12 @@
CSCONFIG_ROW_BIT_13 | \
CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_CLK_CNTL (\
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_DDR_INTERVAL (\
- (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_Q_DRN)
-#define CONFIG_SYS_DDR_MODE 0x47860452
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 (\
- (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 (\
- (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_PAXE_BASE 0xA0000000
-#define CONFIG_SYS_PAXE_SIZE 256
-
-
-/*
* BFTIC3 on the local bus CS4
*/
#define CONFIG_SYS_BFTIC3_BASE 0xB0000000
#define CONFIG_SYS_BFTIC3_SIZE 256
-
/* enable POST tests */
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS)
#define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index 290108d..bfa7ca2 100644
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -8,277 +8,23 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/* KMBEC FPGA (PRIO) */
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 64
-
#define CONFIG_HOSTNAME "kmeter1"
#define CONFIG_KM_BOARD_NAME "kmeter1"
#define CONFIG_KM_DEF_NETDEV "netdev=eth2\0"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Setup
- */
-#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI)
-
-/**
- * DDR RAM settings
- */
-#define CONFIG_SYS_DDR_SDRAM_CFG (\
- SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
CSCONFIG_ROW_BIT_13 | \
CSCONFIG_COL_BIT_10 | \
CSCONFIG_ODT_WR_ONLY_CURRENT)
-
-#define CONFIG_SYS_DDR_CLK_CNTL (\
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_DDR_INTERVAL (\
- (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_Q_DRN)
-#define CONFIG_SYS_DDR_MODE 0x47860452
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 (\
- (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 (\
- (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_PAXE_BASE 0xA0000000
-#define CONFIG_SYS_PAXE_SIZE 256
-
-
#endif /* CONFIG */
diff --git a/include/configs/kmopti2.h b/include/configs/kmopti2.h
index f1b7c2f..67e864f 100644
--- a/include/configs/kmopti2.h
+++ b/include/configs/kmopti2.h
@@ -26,292 +26,10 @@
#define CONFIG_KM_BOARD_NAME "kmopti2"
#define CONFIG_HOSTNAME "kmopti2"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
-/*
- * Configuration for C2 on the local bus
- */
-
-
-/*
- * Configuration for C3 on the local bus
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/kmsupx5.h b/include/configs/kmsupx5.h
index 0dd7420..ba33e60 100644
--- a/include/configs/kmsupx5.h
+++ b/include/configs/kmsupx5.h
@@ -26,283 +26,10 @@
#define CONFIG_KM_BOARD_NAME "kmsupx5"
#define CONFIG_HOSTNAME "kmsupx5"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h
index 8f9bbef..701eb53 100644
--- a/include/configs/kmtegr1.h
+++ b/include/configs/kmtegr1.h
@@ -33,340 +33,13 @@
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0 \
- | SICR_1_UART1_UART1RTS \
- | SICR_1_I2C_CKSTOP \
- | SICR_1_IRQ_A_IRQ \
- | SICR_1_IRQ_B_IRQ \
- | SICR_1_GPIO_A_GPIO \
- | SICR_1_GPIO_B_GPIO \
- | SICR_1_GPIO_C_GPIO \
- | SICR_1_GPIO_D_GPIO \
- | SICR_1_GPIO_E_GPIO \
- | SICR_1_GPIO_F_GPIO \
- | SICR_1_USB_A_UART2S \
- | SICR_1_USB_B_UART2RTS \
- | SICR_1_FEC1_FEC1 \
- | SICR_1_FEC2_FEC2 \
- )
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0 \
- | SICR_2_FEC3_FEC3 \
- | SICR_2_HDLC1_A_HDLC1 \
- | SICR_2_ELBC_A_LA \
- | SICR_2_ELBC_B_LCLK \
- | SICR_2_HDLC2_A_HDLC2 \
- | SICR_2_USB_D_GPIO \
- | SICR_2_PCI_PCI \
- | SICR_2_HDLC1_B_HDLC1 \
- | SICR_2_HDLC1_C_HDLC1 \
- | SICR_2_HDLC2_B_GPIO \
- | SICR_2_HDLC2_C_HDLC2 \
- | SICR_2_QUIESCE_B \
- )
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1 0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_RD_NEVER | \
- CSCONFIG_ODT_WR_ONLY_CURRENT | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
/* must be after the include because KMBEC_FPGA is otherwise undefined */
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 2 Local UPMA 16 bit 256MB APP1
- * 3 Local GPCM 16 bit 256MB APP2
- *
- */
-
-
-/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
-#define CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
-#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
-
#endif /* __CONFIG_H */
diff --git a/include/configs/kmtepr2.h b/include/configs/kmtepr2.h
index b77219f..e0c907d 100644
--- a/include/configs/kmtepr2.h
+++ b/include/configs/kmtepr2.h
@@ -26,284 +26,10 @@
#define CONFIG_KM_BOARD_NAME "kmtepr2"
#define CONFIG_HOSTNAME "kmtepr2"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h
index 785475e..6e5d507 100644
--- a/include/configs/kmvect1.h
+++ b/include/configs/kmvect1.h
@@ -25,328 +25,11 @@
/* at end of uboot partition, before env */
#define CONFIG_SYS_QE_FW_ADDR 0xF00B0000
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0 \
- | SICR_1_UART1_UART1RTS \
- | SICR_1_I2C_CKSTOP \
- | SICR_1_IRQ_A_IRQ \
- | SICR_1_IRQ_B_IRQ \
- | SICR_1_GPIO_A_GPIO \
- | SICR_1_GPIO_B_GPIO \
- | SICR_1_GPIO_C_GPIO \
- | SICR_1_GPIO_D_GPIO \
- | SICR_1_GPIO_E_GPIO \
- | SICR_1_GPIO_F_GPIO \
- | SICR_1_USB_A_UART2S \
- | SICR_1_USB_B_UART2RTS \
- | SICR_1_FEC1_FEC1 \
- | SICR_1_FEC2_FEC2 \
- )
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0 \
- | SICR_2_FEC3_FEC3 \
- | SICR_2_HDLC1_A_HDLC1 \
- | SICR_2_ELBC_A_LA \
- | SICR_2_ELBC_B_LCLK \
- | SICR_2_HDLC2_A_HDLC2 \
- | SICR_2_USB_D_GPIO \
- | SICR_2_PCI_PCI \
- | SICR_2_HDLC1_B_HDLC1 \
- | SICR_2_HDLC1_C_HDLC1 \
- | SICR_2_HDLC2_B_GPIO \
- | SICR_2_HDLC2_C_HDLC2 \
- | SICR_2_QUIESCE_B \
- )
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1 0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_RD_NEVER | \
- CSCONFIG_ODT_WR_ONLY_CURRENT | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 2 Local UPMA 16 bit 256MB APP1
- * 3 Local GPCM 16 bit 256MB APP2
- *
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
0x0000c000 | \
@@ -375,15 +58,4 @@
#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
-#define CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
-#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
-
#endif /* __CONFIG_H */
diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h
index 456cd9d..1705f9c 100644
--- a/include/configs/suvd3.h
+++ b/include/configs/suvd3.h
@@ -21,285 +21,13 @@
*/
#define CONFIG_HOSTNAME "suvd3"
-#define CONFIG_KM_BOARD_NAME "suvd3"
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
+#define CONFIG_KM_BOARD_NAME "suvd3"
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 2 Local UPMA 16 bit 256MB APP1
- * 3 Local GPCM 16 bit 256MB APP2
- *
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
0x0000c000 | \
diff --git a/include/configs/tuge1.h b/include/configs/tuge1.h
index 01d8d6b..808538e 100644
--- a/include/configs/tuge1.h
+++ b/include/configs/tuge1.h
@@ -26,283 +26,10 @@
#define CONFIG_KM_BOARD_NAME "tuge1"
#define CONFIG_HOSTNAME "tuge1"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h
index 15a69ce..0eb673a 100644
--- a/include/configs/tuxx1.h
+++ b/include/configs/tuxx1.h
@@ -26,285 +26,11 @@
#define CONFIG_KM_BOARD_NAME "tuxx1"
#define CONFIG_HOSTNAME "tuxx1"
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
/* include common defines/options for all Keymile boards */
#include "km/keymile-common.h"
#include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus Machine PortSz Size Device
- * ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES 4
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 200000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
- {1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START 0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- "newenv=" \
- "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
- "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Init Local Bus Memory Controller:
- * Device on board
- * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE
- * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit)
- *
- * Device on board (continued)
- * Bank Bus Machine PortSz Size KMTEPR2
- * -----------------------------------------------------------------------------
- * 2 Local GPCM 8 bit 256MB NVRAM
- * 3 Local GPCM 8 bit 256MB TEP2 (16 bit)
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
0x0000c000 | \