ARM: DTS: Add Logic PD DM3730 SOM-LV initial support
This adds the device tree. Previous commit added both boards at the
same time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split the SOM-LV from Torpedo
diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi
new file mode 100644
index 0000000..46dae55
--- /dev/null
+++ b/arch/arm/dts/logicpd-som-lv.dtsi
@@ -0,0 +1,271 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0>;
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 3 0>; /* gpio_3 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&vmmc2>;
+ };
+
+ /* HS USB Host PHY on PORT 1 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
+
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ linux,mtd-name = "micron,mt29f4g16abbda3w";
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ gpmc,device-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
+
+ x-loader@0 {
+ label = "x-loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders@80000 {
+ label = "u-boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env@260000 {
+ label = "u-boot-env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel@280000 {
+ label = "kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem@680000 {
+ label = "fs";
+ reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+};
+
+&mmc3 {
+ interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+ pinctrl-0 = <&mmc3_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1273";
+ reg = <2>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+ ref-clock-frequency = <26000000>;
+ };
+};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>;
+
+ mmc3_pins: pinmux_mm3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
+ OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
+ OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
+ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
+ >;
+ };
+ mcbsp2_pins: pinmux_mcbsp2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
+ OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
+ OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
+ OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
+ >;
+ };
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
+ OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
+ OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
+ OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+ OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
+ >;
+ };
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
+ hsusb_otg_pins: pinmux_hsusb_otg_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ >;
+ };
+
+
+};
+
+&omap3_pmx_wkup {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_reset_pin>;
+ hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+};
+
+&uart2 {
+ interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+ twl_power: power {
+ compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
+ ti,use_poweroff;
+ };
+};
+
+&twl_gpio {
+ ti,use-leds;
+};