diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
new file mode 100644
index 0000000..da3c29f
--- /dev/null
+++ b/include/configs/bamboo.h
@@ -0,0 +1,316 @@
+/*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * bamboo.h - configuration for BAMBOO board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_BAMBOO				1	/* Board is BAMBOO           */
+#define CONFIG_440_EP				1	/* Specific PPC440EP support */
+
+#define CONFIG_4xx					1	/* ... PPC4xx family	*/
+#define CONFIG_BOARD_EARLY_INIT_F 	1   /* Call board_early_init_f	*/
+#undef	CFG_DRAM_TEST					/* disable - takes long time! */
+//#define CONFIG_SYS_CLK_FREQ	66666666    /* external freq to pll	*/
+#define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		    */
+#define CFG_FLASH_BASE	    0xfe000000	    /* start of FLASH		*/
+#define CFG_MONITOR_BASE    TEXT_BASE	    /* start of monitor		*/
+#define CFG_PCI_MEMBASE	    0xa0000000	    /* mapped pci memory	*/
+#define CFG_PCI_MEMBASE1    CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2    CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3    CFG_PCI_MEMBASE2 + 0x10000000
+
+
+/*Don't change either of these*/
+#define CFG_PERIPHERAL_BASE 0xef600000	    /* internal peripherals	*/
+#define CFG_PCI_BASE	    0xe0000000	    /* internal PCI regs	*/
+/*Don't change either of these*/
+
+#define CFG_USB_DEVICE 0x50000000
+#define CFG_NVRAM_BASE_ADDR 0x80000000
+#define CFG_BCSR_BASE	    (CFG_NVRAM_BASE_ADDR | 0x2000)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in SDRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_ADDR	  0xf0000000		/* DCache */
+#define CFG_INIT_RAM_END	0x2000
+#define CFG_GBL_DATA_SIZE	256		    	/* num bytes initial data	*/
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
+#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
+#define CFG_KBYTES_SDRAM	( 128 * 1024)	/* 128MB                     */
+//#define CFG_SDRAM_BANKS     (2)
+#define CFG_SDRAM_BANKS     (1)
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CFG_EXT_SERIAL_CLOCK	11059200 /* use external 11.059MHz clk	*/
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SERIAL_MULTI   1
+/*define this if you want console on UART1*/
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * NVRAM/RTC
+ *
+ * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF
+ * The DS1558 code assumes this condition
+ *
+ *----------------------------------------------------------------------*/
+#define CFG_NVRAM_SIZE	    (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
+#define CONFIG_RTC_DS1556	1		         /* DS1556 RTC		*/
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#if 0 /* test-only */
+#define CFG_MAX_FLASH_BANKS	1		    /* number of banks	    */
+#define CFG_MAX_FLASH_SECT	256		    /* sectors per device   */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	120000	    /* Timeout for Flash Write (in ms)	*/
+#else
+#define CFG_FLASH_CFI				/* The flash is CFI compatible  */
+#define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver        */
+#define CFG_FLASH_CFI_AMD_RESET	1		/* AMD RESET for STM 29W320DB!  */
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM               /* Don't use SPD EEPROM for setup    */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#undef  CFG_ENV_IS_IN_NVRAM		    /*No NVRAM on board*/
+#undef	CFG_ENV_IS_IN_FLASH		    /* ... not in flash		*/
+#define CFG_ENV_IS_IN_EEPROM 1
+
+/* Define to allow the user to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_ENV_SIZE		0x200	    /* Size of Environment vars */
+#define CFG_ENV_OFFSET		0x0
+#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+#define CONFIG_BOOTCOMMAND	"bootm 0xfe000000"    /* autoboot command */
+#define CONFIG_BOOTDELAY	3		    /* disable autoboot */
+
+#define CONFIG_LOADS_ECHO		1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII			1	/* MII PHY management		*/
+#define CONFIG_NET_MULTI    1   /* required for netconsole  */
+#define CONFIG_PHY1_ADDR    3
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
+#define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_IPADDR		10.0.4.251
+#define CONFIG_ETHADDR		00:10:EC:00:12:34
+#define CONFIG_ETH1ADDR		00:10:EC:00:12:35
+
+#define CFG_RX_ETH_BUFFER	32	  /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SERVERIP		10.0.4.115
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#ifdef CONFIG_440_EP
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/*Comment this out to enable USB 1.1 device*/
+#define USB_2_0_DEVICE
+#endif /*CONFIG_440_EP*/
+
+#ifdef DEBUG
+#define CONFIG_PANIC_HANG
+#else
+#define CONFIG_HW_WATCHDOG			/* watchdog */
+#endif
+
+#ifdef CONFIG_440_EP
+	/* Need to define POST */
+#define CONFIG_COMMANDS	       ((CONFIG_CMD_DFL	| \
+			CFG_CMD_DATE	|   \
+			CFG_CMD_DHCP	|   \
+			CFG_CMD_DIAG	|   \
+			CFG_CMD_ECHO	|   \
+			CFG_CMD_EEPROM	|   \
+			CFG_CMD_ELF	|   \
+    /*      CFG_CMD_EXT2    |*/ \
+	/*		CFG_CMD_FAT		|*/	\
+			CFG_CMD_I2C	|	\
+	/*		CFG_CMD_IDE		|*/	\
+			CFG_CMD_IRQ	|	\
+    /*     	CFG_CMD_KGDB	|*/	\
+            		CFG_CMD_MII     |   \
+			CFG_CMD_PCI		|	\
+			CFG_CMD_PING	| 	\
+			CFG_CMD_REGINFO | 	\
+			CFG_CMD_SDRAM	|   \
+			CFG_CMD_FLASH   |   \
+	/*		CFG_CMD_SPI		|*/	\
+			CFG_CMD_USB	|	\
+			0 ) & ~CFG_CMD_IMLS)
+#else
+#define CONFIG_COMMANDS	       ((CONFIG_CMD_DFL	| \
+			CFG_CMD_DATE	|   \
+			CFG_CMD_DHCP	|   \
+			CFG_CMD_DIAG	|   \
+			CFG_CMD_ECHO	|   \
+			CFG_CMD_EEPROM	|   \
+			CFG_CMD_ELF	|   \
+    /*      CFG_CMD_EXT2    |*/ \
+	/*		CFG_CMD_FAT		|*/	\
+			CFG_CMD_I2C	|	\
+	/*		CFG_CMD_IDE		|*/	\
+			CFG_CMD_IRQ	|	\
+    /*     	CFG_CMD_KGDB	|*/	\
+            		CFG_CMD_MII     |   \
+			CFG_CMD_PCI		|	\
+			CFG_CMD_PING	| 	\
+			CFG_CMD_REGINFO | 	\
+			CFG_CMD_SDRAM	|   \
+			CFG_CMD_FLASH   |   \
+	/*		CFG_CMD_SPI		|*/	\
+			0 ) & ~CFG_CMD_IMLS)
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+#define CFG_EXTBDINFO		    1	/* To use extended board_into (bd_t) */
+#define CONFIG_LYNXKDI          1   /* support kdi files */
+
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI			            /* include pci support	        */
+#undef  CONFIG_PCI_PNP			        /* do (not) pci plug-and-play         */
+#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
+#define CFG_PCI_TARGBASE    0x80000000  /* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x1014  /* IBM */
+#define CFG_PCI_SUBSYS_ID 0xcafe        /* Whatever */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		8192	/* For IBM 405 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */