sunxi: dts: arm: update devicetree files from Linux-v6.6-rc6
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 32-bit ARM cores, minus the T113s
board and related .dtsi files, which come separately.
Only small changes: Bluetooth got enabled on the C.H.I.P., and a clock
got renamed. More interesting is the addition of a board, for which
U-Boot enablement patches are pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
diff --git a/arch/arm/dts/axp209.dtsi b/arch/arm/dts/axp209.dtsi
index ca240cd..469d0f7 100644
--- a/arch/arm/dts/axp209.dtsi
+++ b/arch/arm/dts/axp209.dtsi
@@ -48,6 +48,13 @@
* http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
*/
+/ {
+ pmic-temp {
+ compatible = "iio-hwmon";
+ io-channels = <&axp_adc 4>; /* Internal temperature */
+ };
+};
+
&axp209 {
compatible = "x-powers,axp209";
interrupt-controller;
diff --git a/arch/arm/dts/sun5i-r8-chip.dts b/arch/arm/dts/sun5i-r8-chip.dts
index fd37bd1..4192c23 100644
--- a/arch/arm/dts/sun5i-r8-chip.dts
+++ b/arch/arm/dts/sun5i-r8-chip.dts
@@ -255,6 +255,12 @@
pinctrl-0 = <&uart3_pg_pins>,
<&uart3_cts_rts_pg_pins>;
status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8723bs-bt";
+ device-wake-gpios = <&axp_gpio 3 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ };
};
&usb_otg {
diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi
index 250d6b8..d7c7b45 100644
--- a/arch/arm/dts/sun5i.dtsi
+++ b/arch/arm/dts/sun5i.dtsi
@@ -286,7 +286,7 @@
clock-names = "ahb",
"tcon-ch0",
"tcon-ch1";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
status = "disabled";
@@ -517,6 +517,15 @@
bias-pull-up;
};
+ /omit-if-no-ref/
+ mmc2_4bit_pe_pins: mmc2-4bit-pe-pins {
+ pins = "PE4", "PE5", "PE6", "PE7",
+ "PE8", "PE9";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
mmc2_8bit_pins: mmc2-8bit-pins {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12", "PC13",
diff --git a/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts b/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
new file mode 100644
index 0000000..577ead1
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+/dts-v1/;
+
+#include "sun7i-a20-icnova-a20.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "In-Circuit ICnova A20 ADB4006";
+ compatible = "incircuit,icnova-a20-adb4006", "incircuit,icnova-a20",
+ "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_YELLOW>;
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+&ac_power_supply {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun7i-a20-icnova-a20.dtsi b/arch/arm/dts/sun7i-a20-icnova-a20.dtsi
new file mode 100644
index 0000000..46616c6
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-icnova-a20.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&gmac_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
diff --git a/arch/arm/dts/sun8i-a23-a33.dtsi b/arch/arm/dts/sun8i-a23-a33.dtsi
index 84c6d93..a0cac96 100644
--- a/arch/arm/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/dts/sun8i-a23-a33.dtsi
@@ -190,7 +190,7 @@
clock-names = "ahb",
"tcon-ch0",
"lvds-alt";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_LCD>,
<&ccu RST_BUS_LVDS>;
diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
index 9c07660..cc40622 100644
--- a/arch/arm/dts/sun8i-a83t.dtsi
+++ b/arch/arm/dts/sun8i-a83t.dtsi
@@ -456,7 +456,7 @@
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
clock-names = "ahb", "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
reset-names = "lcd", "lvds";
diff --git a/arch/arm/dts/sun8i-v3s.dtsi b/arch/arm/dts/sun8i-v3s.dtsi
index b001251..3b9a282 100644
--- a/arch/arm/dts/sun8i-v3s.dtsi
+++ b/arch/arm/dts/sun8i-v3s.dtsi
@@ -191,7 +191,7 @@
<&ccu CLK_TCON0>;
clock-names = "ahb",
"tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>;
reset-names = "lcd";