Added support for the SOLIDCARD III board from Eurodesign
Signed-off-by: Heiko Schocher <hs@denx.de>
diff --git a/include/configs/SOLIDCARD3.h b/include/configs/SOLIDCARD3.h
new file mode 100644
index 0000000..16e68b5
--- /dev/null
+++ b/include/configs/SOLIDCARD3.h
@@ -0,0 +1,537 @@
+/*
+ * (C) Copyright 2007
+ * Heiko Schocher, DENX Software Engineering, <hs@denx.de>.
+ *
+ * From:
+ * (C) Copyright 2003
+ * Juergen Beisert, EuroDesign embedded technologies, jbeisert@eurodsn.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef USE_VGA_GRAPHICS
+
+/* Memory Map
+0x00000000 .... 0x03FFFFFF -> RAM (up to 128MiB)
+0x74000000 .... 0x740FFFFF -> CS#6
+0x74100000 .... 0x741FFFFF -> CS#7
+0x74200000 .... 0x742FFFFF -> CS4# if no internal USB
+0x74300000 .... 0x743FFFFF -> CS5# if no boosted IDE
+0x77C00000 .... 0x77CFFFFF -> CS4# USB HC (1 MiB)
+0x77D00000 .... 0x77DFFFFF -> CS1# NAND-Flash (1 MiB)
+0x78000000 .... 0x78FFFFFF -> CS2# ISA-Bus Speicherzugriff (16 MiB)
+0x79000000 .... 0x7900FFFF -> CS2# ISA-Bus IO-Zugriff (16 MiB, mapped: 64kiB)
+0x79010000 .... 0x79FFFFFF -> CS2# ISA-Bus IO-Zugriff (mirrored)
+0x7A000000 .... 0x7A0FFFFF -> CS5# IDE emulation (1MiB)
+
+0x80000000 .... 0x9FFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 1:1)
+0xA0000000 .... 0xBFFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 0x00000000...0x1FFFFFFF)
+0xE8000000 .... 0xE800FFFF -> PCI-Bus IO-Zugriff (64kiB, translated to PCI: 0x0000...0xFFFF)
+0xE8800000 .... 0xEBFFFFFF -> PCI-Bus IO-Zugriff (56MiB, translated to PCI: 0x00800000...0x3FFFFFF)
+0xEED00000 .... 0xEED00003 -> PCI-Bus
+0xEF400000 .... 0xEF40003F -> PCI-Bus Local Configuration Registers
+0xEF40003F .... 0xEF5FFFFF -> reserved
+0xEF600000 .... 0xEFFFFFFF -> 405GP internal Devices (10 MiB)
+0xF0000000 .... 0xF01FFFFF -> Flash-ROM (2 MiB)
+0xF0200000 .... 0xF7FFFFFF -> free for flash devices
+0xF8000000 .... 0xF8000FFF -> OnChipMemory (4kiB)
+0xF8001000 .... 0xFFDFFFFF -> free for flash devices
+0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB)
+*/
+
+#define CONFIG_SOLIDCARD3 1
+#define CONFIG_4xx 1
+#define CONFIG_405GP 1
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+/*
+ * define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
+ * If undefed, IDE access uses a seperat emulation with higher access speed
+ * Consider to inform your Linux IDE driver about the different addresses!
+ * IDE_USES_ISA_EMULATION is only used if your CONFIG_COMMANDS macro includes the CFG_CMD_IDE macro!
+ */
+#define IDE_USES_ISA_EMULATION
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_SERIAL_MULTI
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+/*
+ * define CONFIG_POWER_DOWN if your cpu should power down while waiting for your input
+ * Works only, if you have enabled the CONFIG_SERIAL_SOFTWARE_FIFO feature
+ */
+#if CONFIG_SERIAL_SOFTWARE_FIFO
+ #define CONFIG_POWER_DOWN
+#endif
+
+/*
+ * define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz
+ */
+#define CONFIG_SYS_CLK_FREQ 33333333
+
+/*
+ * define CONFIG_BAUDRATE to the baudrate value you want to use as default
+ */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#if 1 /* feel free to disable for development */
+#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
+#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with S\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "S" /* 1st "password" */
+#endif
+
+/*
+ * define CONFIG_BOOTCOMMAND to the autoboot commands. They will running after
+ * the CONFIG_BOOTDELAY delay to boot your machine
+ */
+#define CONFIG_BOOTCOMMAND "bootp;dcache on;bootm"
+
+/*
+ * define CONFIG_BOOTARGS to the default kernel parameters. They will used if you don't
+ * set different values at the u-boot prompt
+ */
+#ifdef USE_VGA_GRAPHICS
+ #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp nfsroot=/tftpboot/solidcard3re"
+#else
+ #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs rw ip=bootp"
+#endif
+/*
+ * Is the USB host controller assembled? If yes define CONFIG_ISP1161_PRESENT
+ * This reserves memory bank #4 for this purpose
+ */
+#undef CONFIG_ISP1161_PRESENT
+
+#undef CONFIG_LOADS_ECHO /* no echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_NET_MULTI
+/* #define CONFIG_EEPRO100_SROM_WRITE */
+/* #define CONFIG_SHOW_MAC */
+#define CONFIG_EEPRO100
+#define CONFIG_MII 1 /* add 405GP MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */
+
+#define CONFIG_COMMANDS \
+ (CONFIG_CMD_DFL | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_NET | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_NAND | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IDE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_ELF )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP 1 /* undef to save memory */
+#define CFG_PROMPT "SC3> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/*
+ * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ * baseBaud = cpuClock/(uartDivisor*16)
+ * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ *
+ * Consider the OPB clock! If it get lower the BASE_BAUD must be lower to
+ * (see 405GP datasheet for descritpion)
+ */
+#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD 921600 /* internal clock */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+#define CFG_LOAD_ADDR 0x1000000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * IIC stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+
+#define I2C_INIT
+#define I2C_ACTIVE 0
+#define I2C_TRISTATE 0
+
+#define CFG_I2C_SPEED 100000 /* use the standard 100kHz speed */
+#define CFG_I2C_SLAVE 0x7F /* mask valid bits */
+
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR 0x68
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+/* If you want to see, whats connected to your PCI bus */
+/* #define CONFIG_PCI_SCAN_SHOW */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
+#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * External peripheral base address
+ *-----------------------------------------------------------------------
+ */
+#if !(CONFIG_COMMANDS & CFG_CMD_IDE)
+
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#else /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+#define CONFIG_START_IDE 1 /* check, if use IDE */
+
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CONFIG_ATAPI
+#define CONFIG_DOS_PARTITION
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#ifndef IDE_USES_ISA_EMULATION
+
+/* New and faster access */
+#define CFG_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */
+
+/* How many IDE busses are available */
+#define CFG_IDE_MAXBUS 1
+
+/* What IDE ports are available */
+#define CFG_ATA_IDE0_OFFSET 0x000 /* first is available */
+#undef CFG_ATA_IDE1_OFFSET /* second not available */
+
+/* access to the data port is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_DATA_OFFSET + 0 */
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+
+/* access to the registers is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_REG_OFFSET + [1..7] */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+
+/* access to the alternate register is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_ALT_OFFSET + 6 */
+#define CFG_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */
+
+#else /* IDE_USES_ISA_EMULATION */
+
+#define CFG_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */
+
+/* How many IDE busses are available */
+#define CFG_IDE_MAXBUS 1
+
+/* What IDE ports are available */
+#define CFG_ATA_IDE0_OFFSET 0x01F0 /* first is available */
+#undef CFG_ATA_IDE1_OFFSET /* second not available */
+
+/* access to the data port is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_DATA_OFFSET + 0 */
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+
+/* access to the registers is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_REG_OFFSET + [1..7] */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+
+/* access to the alternate register is calculated:
+ CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_ALT_OFFSET + 6 */
+#define CFG_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */
+
+#endif /* IDE_USES_ISA_EMULATION */
+
+#endif /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+
+/*
+#define CFG_KEY_REG_BASE_ADDR 0xF0100000
+#define CFG_IR_REG_BASE_ADDR 0xF0200000
+#define CFG_FPGA_REG_BASE_ADDR 0xF0300000
+*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * CFG_FLASH_BASE -> start address of internal flash
+ * CFG_MONITOR_BASE -> start of u-boot
+ */
+#ifndef __ASSEMBLER__
+extern unsigned long offsetOfBigFlash;
+extern unsigned long offsetOfEnvironment;
+#endif
+
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFE00000
+#define CFG_MONITOR_BASE 0xFFFC0000 /* placed last 256k */
+#define CFG_MONITOR_LEN (224 * 1024) /* Reserve 224 KiB for Monitor */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MiB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization // FIXME: lookup in datasheet
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_CFI /* flash is CFI compat. */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
+#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#if CFG_ENV_IS_IN_FLASH
+ #define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */
+ #define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+ #define CFG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */
+#endif
+/* let us changing anything in our environment */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * NAND-FLASH stuff
+ */
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CFG_NAND_BASE 0x77D00000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *
+ * CFG_DCACHE_SIZE -> size of data cache:
+ * - 405GP 8k
+ * - 405GPr 16k
+ * How to handle the difference in chache size?
+ * CFG_CACHELINE_SIZE -> size of one cache line: 32 bytes
+ * (used in cpu/ppc4xx/start.S)
+*/
+#define CFG_DCACHE_SIZE 16384
+
+#define CFG_CACHELINE_SIZE 32
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ */
+
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE
+#define FLASH_BASE1_PRELIM 0
+
+/*-----------------------------------------------------------------------
+ * Some informations about the internal SRAM (OCM=On Chip Memory)
+ *
+ * CFG_OCM_DATA_ADDR -> location
+ * CFG_OCM_DATA_SIZE -> size
+*/
+
+#define CFG_TEMP_STACK_OCM 1
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM):
+ * - we are using the internal 4k SRAM, so we don't need data cache mapping
+ * - internal SRAM (OCM=On Chip Memory) is placed to CFG_OCM_DATA_ADDR
+ * - Stackpointer will be located to
+ * (CFG_INIT_RAM_ADDR&0xFFFF0000) | (CFG_INIT_SP_OFFSET&0x0000FFFF)
+ * in cpu/ppc4xx/start.S
+ */
+
+#undef CFG_INIT_DCACHE_CS
+/* Where the internal SRAM starts */
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR
+/* Where the internal SRAM ends (only offset) */
+#define CFG_INIT_RAM_END 0x0F00
+
+/*
+
+ CFG_INIT_RAM_ADDR ------> ------------ lower address
+ | |
+ | ^ |
+ | | |
+ | | Stack |
+ CFG_GBL_DATA_OFFSET ----> ------------
+ | |
+ | 64 Bytes |
+ | |
+ CFG_INIT_RAM_END ------> ------------ higher address
+ (offset only)
+
+*/
+/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_SIZE 64
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+/* Initial value of the stack pointern in internal SRAM */
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/* ################################################################################### */
+/* These defines will be used in cpu/ppc4xx/cpu_init.c to setup external chip selects */
+/* They are currently undefined cause they are initiaized in board/solidcard3/init.S */
+
+/* This chip select accesses the boot device */
+/* It depends on boot select switch if this device is 16 or 8 bit */
+
+#undef CFG_EBC_PB0AP
+#undef CFG_EBC_PB0CR
+
+#undef CFG_EBC_PB1AP
+#undef CFG_EBC_PB1CR
+
+#undef CFG_EBC_PB2AP
+#undef CFG_EBC_PB2CR
+
+#undef CFG_EBC_PB3AP
+#undef CFG_EBC_PB3CR
+
+#undef CFG_EBC_PB4AP
+#undef CFG_EBC_PB4CR
+
+#undef CFG_EBC_PB5AP
+#undef CFG_EBC_PB5CR
+
+#undef CFG_EBC_PB6AP
+#undef CFG_EBC_PB6CR
+
+#undef CFG_EBC_PB7AP
+#undef CFG_EBC_PB7CR
+
+#define CONFIG_SDRAM_BANK0 /* use the standard SDRAM initialization */
+#undef CONFIG_SPD_EEPROM
+
+/*
+ * Define this to get more information about system configuration
+ */
+/* #define SC3_DEBUGOUT */
+#undef SC3_DEBUGOUT
+
+/***********************************************************************
+ * External peripheral base address
+ ***********************************************************************/
+
+#define CFG_ISA_MEM_BASE_ADDRESS 0x78000000
+/*
+ Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu.
+ Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die
+ das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen
+ auf ISA- und PCI-Zyklen)
+ */
+#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000
+/*#define CFG_ISA_IO_BASE_ADDRESS 0x79000000 */
+
+/************************************************************
+ * Video support
+ ************************************************************/
+
+#ifdef USE_VGA_GRAPHICS
+#define CONFIG_VIDEO /* To enable video controller support */
+#define CONFIG_VIDEO_CT69000
+#define CONFIG_CFB_CONSOLE
+/* #define CONFIG_VIDEO_LOGO */
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_SW_CURSOR
+/* #define CONFIG_VIDEO_HW_CURSOR */
+#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
+
+#define VIDEO_HW_RECTFILL
+#define VIDEO_HW_BITBLT
+
+#endif
+
+/************************************************************
+ * Ident
+ ************************************************************/
+#define CONFIG_SC3_VERSION "r1.4"
+
+#define POST_OUT(x) (*((volatile unsigned char*)(0x79000080))=x)
+
+#endif /* __CONFIG_H */