powerpc/km: remove unmaintained board KMLION1
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h
index c50026d..75480a8 100644
--- a/include/configs/kmp204x.h
+++ b/include/configs/kmp204x.h
@@ -7,13 +7,7 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/* KMLION1 */
-#if defined(CONFIG_KMLION1)
-#define CONFIG_HOSTNAME "kmlion1"
-#define CONFIG_KM_BOARD_NAME "kmlion1"
-
-/* KMCOGE4 */
-#elif defined(CONFIG_KMCOGE4)
+#if defined(CONFIG_KMCOGE4)
#define CONFIG_HOSTNAME "kmcoge4"
#define CONFIG_KM_BOARD_NAME "kmcoge4"
@@ -23,31 +17,407 @@
#define CONFIG_KMP204X
+#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
+
+/* an additionnal option is required for UBI as subpage access is
+ * supported in u-boot
+ */
+#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
+
+#define CONFIG_NAND_ECC_BCH
+
+/* common KM defines */
+#include "km/keymile-common.h"
+
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
+
+/* High Level Configuration Options */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_SYS_DPAA_RMAN /* RMan */
+
+/* Environment in SPI Flash */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */
+#define CONFIG_ENV_SIZE 0x004000 /* 16K env */
+#define CONFIG_ENV_SECT_SIZE 0x010000
+#define CONFIG_ENV_OFFSET_REDUND 0x110000
+#define CONFIG_ENV_TOTAL_SIZE 0x020000
+
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+
+#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
+ CONFIG_RAMBOOT_TEXT_BASE)
+#define CONFIG_SYS_L3_SIZE (1024 << 10)
+#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
+
-#include "km/kmp204x-common.h"
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-#if defined(CONFIG_KMLION1)
-/* App1 Local bus */
-#define CONFIG_SYS_LBAPP1_BASE 0xD0000000
-#define CONFIG_SYS_LBAPP1_BASE_PHYS 0xFD0000000ull
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_SYS_LBAPP1_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP1_BASE_PHYS) \
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x54
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+
+/******************************************************************************
+ * (PRAM usage)
+ * ... -------------------------------------------------------
+ * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
+ * ... |<------------------- pram -------------------------->|
+ * ... -------------------------------------------------------
+ * @END_OF_RAM:
+ * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
+ * @CONFIG_KM_PHRAM: address for /var
+ * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
+ * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
+ */
+
+/* size of rootfs in RAM */
+#define CONFIG_KM_ROOTFSSIZE 0x0
+/* pseudo-non volatile RAM [hex] */
+#define CONFIG_KM_PNVRAM 0x80000
+/* physical RAM MTD size [hex] */
+#define CONFIG_KM_PHRAM 0x100000
+/* reserved pram area at the end of memory [hex]
+ * u-boot reserves some memory for the MP boot page
+ */
+#define CONFIG_KM_RESERVED_PRAM 0x1000
+/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
+ * is not valid yet, which is the case for when u-boot copies itself to RAM
+ */
+#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM) >> 10)
+
+#define CONFIG_KM_CRAMFS_ADDR 0x2000000
+#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
+#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
+
+/*
+ * Local Bus Definitions
+ */
+
+/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
+
+/* Nand Flash */
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+
+#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
+ | OR_FCM_BCTLD /* LBCTL not ass */ \
+ | OR_FCM_SCY_1 /* 1 clk wait cycle */ \
+ | OR_FCM_RST /* 1 clk read setup */ \
+ | OR_FCM_PGS /* Large page size */ \
+ | OR_FCM_CST) /* 0.25 command setup */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+
+/* QRIO FPGA */
+#define CONFIG_SYS_QRIO_BASE 0xfb000000
+#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
+
+#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
| BR_PS_8 /* Port Size 8 bits */ \
| BR_DECC_OFF /* no error corr */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_LBAPP1_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
- | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
- | OR_GPCM_CSNT /* LCS 1/4 clk before */ \
+#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
+ | OR_GPCM_BCTLD /* no LCTL assert */ \
+ | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
| OR_GPCM_TRLX /* relaxed tmgs */ \
| OR_GPCM_EAD) /* extra bus clk cycles */
-/* Local bus app1 Base Address */
-#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_LBAPP1_BR_PRELIM
-/* Local bus app1 Options */
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_LBAPP1_OR_PRELIM
+
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
+
+#define CONFIG_MISC_INIT_F
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x11D600)
+
+#define CONFIG_KM_CONSOLE_TTY "ttyS0"
+
+/* I2C */
+
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
+#define CONFIG_SYS_NUM_I2C_BUSES 3
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
+ }
+#ifndef __ASSEMBLY__
+void set_sda(int state);
+void set_scl(int state);
+int get_sda(void);
+int get_scl(void);
+#endif
+
+#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
+
+/*
+ * eSPI - Enhanced SPI
+ */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 10
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
+ CONFIG_SYS_BMAN_CENA_SIZE)
+#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
+#define CONFIG_SYS_QMAN_NUM_PORTALS 10
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
+ CONFIG_SYS_QMAN_CENA_SIZE)
+#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+/* Default address of microcode for the Linux Fman driver
+ * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
+ * ucode is stored after env, so we got 0x120000.
+ */
+#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+
+#define CONFIG_PHYLIB_10G
+
+#define CONFIG_PCI_INDIRECT_BRIDGE
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_ETHPRIME "FM1@DTSEC5"
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Hardware Watchdog
+ */
+#define CONFIG_WATCHDOG /* enable CPU watchdog */
+#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
+#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
+
+/*
+ * additionnal command line configuration.
+ */
+
+/* we don't need flash support */
+#undef CONFIG_JFFS2_CMDLINE
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+#define __USB_PHY_TYPE utmi
+#define CONFIG_USB_EHCI_FSL
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
#endif
+/* architecture specific default bootargs */
+#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
+
+/* FIXME: FDT_ADDR is unspecified */
+#define CONFIG_KM_DEF_ENV_CPU \
+ "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
+ "cramfsloadfdt=" \
+ "cramfsload ${fdt_addr_r} " \
+ "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
+ "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
+ "u-boot=" CONFIG_HOSTNAME "/u-boot.pbl\0" \
+ "update=" \
+ "sf probe 0;sf erase 0 +${filesize};" \
+ "sf write ${load_addr_r} 0 ${filesize};\0" \
+ "set_fdthigh=true\0" \
+ "checkfdt=true\0" \
+ ""
+
+#define CONFIG_HW_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
+ "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
+ "usb_dr_mode=host\0"
+
+#define CONFIG_KM_NEW_ENV \
+ "newenv=sf probe 0;" \
+ "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
+ __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
+
+/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ CONFIG_KM_DEF_ARCH \
+ CONFIG_KM_NEW_ENV \
+ CONFIG_HW_ENV_SETTINGS \
+ "EEprom_ivm=pca9547:70:9\0" \
+ ""
+
/* App2 Local bus */
#define CONFIG_SYS_LBAPP2_BASE 0xE0000000
#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull