board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
diff --git a/include/configs/pg-wcom-expu1.h b/include/configs/pg-wcom-expu1.h
new file mode 100644
index 0000000..e08d941
--- /dev/null
+++ b/include/configs/pg-wcom-expu1.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2020 Hitachi ABB Power Grids
+ */
+
+#ifndef __CONFIG_PG_WCOM_EXPU1_H
+#define __CONFIG_PG_WCOM_EXPU1_H
+
+#define WCOM_EXPU1
+#define CONFIG_HOSTNAME "EXPU1"
+
+#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0"
+#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"
+
+/* CLIPS FPGA Definitions */
+#define CONFIG_SYS_CSPR3_EXT (0x00)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CLIPS_BASE) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \
+ CSOR_GPCM_TRHZ_40)
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \
+ FTIM0_GPCM_TEADC(0x7) | \
+ FTIM0_GPCM_TEAHC(0x2))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \
+ FTIM1_GPCM_TRAD(0x12))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \
+ FTIM2_GPCM_TCH(0x1) | \
+ FTIM2_GPCM_TWP(0x12))
+#define CONFIG_SYS_CS3_FTIM3 0x04000000
+
+/* PRST */
+#define WCOM_CLIPS_RST 0
+#define WCOM_QSFP_RST 1
+#define WCOM_PHY_RST 2
+#define WCOM_TMG_RST 3
+#define KM_DBG_ETH_RST 15
+
+/* QRIO GPIOs used for deblocking */
+#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
+#define KM_I2C_DEBLOCK_SCL 20
+#define KM_I2C_DEBLOCK_SDA 21
+
+/* ZL30343 on SPI */
+#define WCOM_ZL30343_CFG_ADDR 0xe8070000
+#define WCOM_ZL30343_SPI_BUS 0
+#define WCOM_ZL30343_CS 0
+
+#include "km/pg-wcom-ls102xa.h"
+
+#endif /* __CONFIG_PG_WCOM_EXPU1_H */