configs: Add am62x_beagleplay_*_defconfig
Add am62x_beagleplay_* defconfig customized for the configuration of
BeaglePlay and drop the config fragments.
This is in preparation for dropping the dependency on ti vendor folder
entirely.
Signed-off-by: Nishanth Menon <nm@ti.com>
diff --git a/board/ti/am62x/beagleplay_a53.config b/board/ti/am62x/beagleplay_a53.config
deleted file mode 100644
index f038041..0000000
--- a/board/ti/am62x/beagleplay_a53.config
+++ /dev/null
@@ -1,55 +0,0 @@
-# Defconfig fragment to apply on top of am62x_evm_a53_defconfig
-
-CONFIG_DEFAULT_DEVICE_TREE="k3-am625-beagleplay"
-CONFIG_OF_LIST="k3-am625-beagleplay"
-CONFIG_SPL_OF_LIST="k3-am625-beagleplay"
-CONFIG_BOOTCOMMAND="run set_led_state_start_load;run findfdt; run envboot; bootflow scan -lb;run set_led_state_fail_load"
-CONFIG_EXT4_WRITE=y
-CONFIG_LZO=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
-CONFIG_AUTOBOOT_DELAY_STR="d"
-CONFIG_AUTOBOOT_STOP_STR=" "
-# Use the Beagleplay env file
-CONFIG_ENV_SOURCE_FILE="beagleplay"
-# Do not use emmc boot - we will use FS only
-CONFIG_SUPPORT_EMMC_BOOT=n
-CONFIG_MMC_IO_VOLTAGE=y
-# CONFIG_SPL_MMC_IO_VOLTAGE is not set
-CONFIG_MMC_UHS_SUPPORT=y
-# CONFIG_SPL_MMC_UHS_SUPPORT is not set
-CONFIG_MMC_HS200_SUPPORT=y
-# CONFIG_SPL_MMC_HS200_SUPPORT is not set
-# Enable GPIO control
-CONFIG_DM_GPIO=y
-CONFIG_SPL_GPIO=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPIO_READ=y
-# Enable LEDs
-CONFIG_LED=y
-CONFIG_LED_GPIO=y
-CONFIG_SPL_LED=y
-CONFIG_SPL_LED_GPIO=y
-# Enable I2C bus
-CONFIG_SPL_I2C=y
-CONFIG_DM_I2C=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_CMD_I2C=y
-# Regulator
-CONFIG_DM_REGULATOR=y
-CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_DM_REGULATOR_GPIO=y
-CONFIG_CMD_REGULATOR=y
-CONFIG_DM_REGULATOR_TPS65219=y
-CONFIG_DM_PMIC=y
-CONFIG_PMIC_TPS65219=y
-CONFIG_CMD_PMIC=y
-# Uses Realtek phy rather than TI phy
-CONFIG_PHY_TI_DP83867=n
-CONFIG_PHY_REALTEK=y
-# No SPI flash on Beagleplay
-CONFIG_SPI=n
-CONFIG_SPI_FLASH=n
-CONFIG_SPL_DM_SPI_FLASH=n
-CONFIG_SPL_SPI_FLASH_SUPPORT=n
diff --git a/board/ti/am62x/beagleplay_r5.config b/board/ti/am62x/beagleplay_r5.config
deleted file mode 100644
index 4ee0375..0000000
--- a/board/ti/am62x/beagleplay_r5.config
+++ /dev/null
@@ -1,15 +0,0 @@
-# Defconfig fragment to apply on top of:
-# am62x_evm_r5_defconfig
-#
-CONFIG_DEFAULT_DEVICE_TREE="k3-am625-r5-beagleplay"
-CONFIG_OF_LIST="k3-am625-r5-beagleplay"
-CONFIG_SPL_OF_LIST="k3-am625-r5-beagleplay"
-# Do spl board init
-CONFIG_SPL_BOARD_INIT=y
-# Do not use emmc boot - we will use FS only
-CONFIG_SUPPORT_EMMC_BOOT=n
-# No SPI flash on Beagleplay
-CONFIG_SPI=n
-CONFIG_SPI_FLASH=n
-CONFIG_SPL_DM_SPI_FLASH=n
-CONFIG_SPL_SPI_FLASH_SUPPORT=n
diff --git a/configs/am62x_beagleplay_a53_defconfig b/configs/am62x_beagleplay_a53_defconfig
new file mode 100644
index 0000000..eca94a0
--- /dev/null
+++ b/configs/am62x_beagleplay_a53_defconfig
@@ -0,0 +1,119 @@
+CONFIG_ARM=y
+CONFIG_ARCH_K3=y
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_SOC_K3_AM625=y
+CONFIG_K3_ATF_LOAD_ADDR=0x9e780000
+CONFIG_TARGET_AM625_A53_EVM=y
+CONFIG_ENV_SOURCE_FILE="beagleplay"
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80b80000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="k3-am625-beagleplay"
+CONFIG_SPL_TEXT_BASE=0x80080000
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_DM_RESET=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SPL_SIZE_LIMIT=0x40000
+CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x800
+CONFIG_SPL_FS_FAT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+# CONFIG_PSCI_RESET is not set
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
+CONFIG_BOOTSTD_FULL=y
+CONFIG_BOOTSTD_DEFAULTS=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
+CONFIG_AUTOBOOT_DELAY_STR="d"
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_BOOTCOMMAND="run set_led_state_start_load;run findfdt; run envboot; bootflow scan -lb;run set_led_state_fail_load"
+CONFIG_SPL_MAX_SIZE=0x58000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x80c80000
+CONFIG_SPL_BSS_MAX_SIZE=0x80000
+CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
+CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
+CONFIG_SPL_I2C=y
+CONFIG_SPL_DM_MAILBOX=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_YMODEM_SUPPORT=y
+CONFIG_SYS_BOOTM_LEN=0x800000
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPIO_READ=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_TI_SCI=y
+CONFIG_DMA_CHANNELS=y
+CONFIG_TI_K3_NAVSS_UDMA=y
+CONFIG_TI_SCI_PROTOCOL=y
+CONFIG_DA8XX_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_OMAP24XX=y
+CONFIG_LED=y
+CONFIG_SPL_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SPL_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_K3_SEC_PROXY=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ADMA=y
+CONFIG_SPL_MMC_SDHCI_ADMA=y
+CONFIG_MMC_SDHCI_AM654=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_TI=y
+CONFIG_PHY_FIXED=y
+CONFIG_TI_AM65_CPSW_NUSS=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_TI_SCI_POWER_DOMAIN=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_TPS65219=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_REGULATOR_TPS65219=y
+CONFIG_K3_SYSTEM_CONTROLLER=y
+CONFIG_REMOTEPROC_TI_K3_ARM64=y
+CONFIG_RESET_TI_SCI=y
+CONFIG_DM_SERIAL=y
+CONFIG_SOC_DEVICE=y
+CONFIG_SOC_DEVICE_TI_K3=y
+CONFIG_SOC_TI=y
+CONFIG_SYSRESET=y
+CONFIG_SPL_SYSRESET=y
+CONFIG_SYSRESET_TI_SCI=y
+CONFIG_EXT4_WRITE=y
+CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
+CONFIG_LZO=y
diff --git a/configs/am62x_beagleplay_r5_defconfig b/configs/am62x_beagleplay_r5_defconfig
new file mode 100644
index 0000000..44d4442
--- /dev/null
+++ b/configs/am62x_beagleplay_r5_defconfig
@@ -0,0 +1,111 @@
+CONFIG_ARM=y
+CONFIG_ARCH_K3=y
+CONFIG_SYS_MALLOC_LEN=0x08000000
+CONFIG_SYS_MALLOC_F_LEN=0x9000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_SOC_K3_AM625=y
+CONFIG_TARGET_AM625_R5_EVM=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x43c3a7f0
+CONFIG_ENV_SIZE=0x20000
+CONFIG_DM_GPIO=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="k3-am625-r5-beagleplay"
+CONFIG_SPL_TEXT_BASE=0x43c00000
+CONFIG_DM_RESET=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x7000
+CONFIG_SPL_SIZE_LIMIT=0x3A7F0
+CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x3500
+CONFIG_SPL_FS_FAT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_SIZE_LIMIT_SUBTRACT_GD=y
+CONFIG_SPL_SIZE_LIMIT_SUBTRACT_MALLOC=y
+CONFIG_SPL_MAX_SIZE=0x3B000
+CONFIG_SPL_PAD_TO=0x0
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x43c3b000
+CONFIG_SPL_BSS_MAX_SIZE=0x3000
+CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_SYS_MALLOC=y
+CONFIG_SPL_HAS_CUSTOM_MALLOC_START=y
+CONFIG_SPL_CUSTOM_SYS_MALLOC_ADDR=0x84000000
+CONFIG_SPL_SYS_MALLOC_SIZE=0x1000000
+CONFIG_SPL_EARLY_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x400
+CONFIG_SPL_DM_MAILBOX=y
+CONFIG_SPL_DM_RESET=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_RAM_SUPPORT=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_REMOTEPROC=y
+CONFIG_SPL_YMODEM_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_REMOTEPROC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TIME=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_SPL_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+# CONFIG_NET is not set
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_SPL_CLK_CCF=y
+CONFIG_SPL_CLK_K3_PLL=y
+CONFIG_SPL_CLK_K3=y
+CONFIG_TI_SCI_PROTOCOL=y
+CONFIG_DA8XX_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_K3_SEC_PROXY=y
+CONFIG_SPL_MISC=y
+CONFIG_ESM_K3=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ADMA=y
+CONFIG_SPL_MMC_SDHCI_ADMA=y
+CONFIG_MMC_SDHCI_AM654=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_GENERIC is not set
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_GENERIC is not set
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_TI_POWER_DOMAIN=y
+CONFIG_K3_SYSTEM_CONTROLLER=y
+CONFIG_REMOTEPROC_TI_K3_ARM64=y
+CONFIG_RESET_TI_SCI=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DM_SERIAL=y
+CONFIG_SOC_DEVICE=y
+CONFIG_SOC_DEVICE_TI_K3=y
+CONFIG_SOC_TI=y
+CONFIG_TIMER=y
+CONFIG_SPL_TIMER=y
+CONFIG_OMAP_TIMER=y
+CONFIG_LIB_RATIONAL=y
+CONFIG_SPL_LIB_RATIONAL=y
diff --git a/doc/board/ti/am62x_beagleplay.rst b/doc/board/ti/am62x_beagleplay.rst
index 44e728d..ea6c858 100644
--- a/doc/board/ti/am62x_beagleplay.rst
+++ b/doc/board/ti/am62x_beagleplay.rst
@@ -57,8 +57,8 @@
:end-before: .. k3_rst_include_end_common_env_vars_defn
.. prompt:: bash $
- export UBOOT_CFG_CORTEXR="am62x_evm_r5_defconfig beagleplay_r5.config"
- export UBOOT_CFG_CORTEXA="am62x_evm_a53_defconfig beagleplay_a53.config"
+ export UBOOT_CFG_CORTEXR=am62x_beagleplay_r5_defconfig
+ export UBOOT_CFG_CORTEXA=am62x_beagleplay_a53_defconfig
export TFA_BOARD=lite
# we dont use any extra TFA parameters
unset TFA_EXTRA_ARGS