diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts
index 35ff4e7..9f86649 100644
--- a/arch/arm/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-a-plus.dts
@@ -1,6 +1,7 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
@@ -21,7 +22,72 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	/*
+	 * This is based on the unreleased schematic for the Model A+.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "USB_LIMIT", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
@@ -33,3 +99,9 @@
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts
index 306a84e..4b1af06 100644
--- a/arch/arm/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/dts/bcm2835-rpi-a.dts
@@ -1,6 +1,7 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,model-a", "brcm,bcm2835";
@@ -14,7 +15,74 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_GPIO1",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "CAM_GPIO0",
+			  /* Binary number representing build/revision */
+			  "CONFIG0",
+			  "CONFIG1",
+			  "CONFIG2",
+			  "CONFIG3",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
 	i2s_alt2: i2s_alt2 {
@@ -26,3 +94,9 @@
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts
index d5fdb8e..a846f1e 100644
--- a/arch/arm/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-plus.dts
@@ -2,6 +2,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
@@ -22,7 +23,73 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
+	 * RPI-BPLUS sheet 1
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "LAN_RUN", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "PWR_LOW_N", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "USB_LIMIT", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "ETHCLK", /* GPIO44 */
+			  "PWM1_OUT", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
@@ -34,3 +101,9 @@
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
index bfc4bd9..e860964 100644
--- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
@@ -2,6 +2,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
@@ -15,7 +16,73 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf
+	 * RPI00022 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_CLK",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "CAM_GPIO",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
 	i2s_alt2: i2s_alt2 {
@@ -27,3 +94,9 @@
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
index 0371bb7..5d77f3f 100644
--- a/arch/arm/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -2,6 +2,7 @@
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
@@ -15,9 +16,82 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &alt3>;
+	/*
+	 * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+	 * RPI00021 sheet 02
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "SDA0",
+			  "SCL0",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "CAM_GPIO1",
+			  "LAN_RUN",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "NC", /* GPIO12 */
+			  "NC", /* GPIO13 */
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "STATUS_LED_N",
+			  "GPIO17",
+			  "GPIO18",
+			  "NC", /* GPIO19 */
+			  "NC", /* GPIO20 */
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "NC", /* GPIO26 */
+			  "CAM_GPIO0",
+			  /* Binary number representing build/revision */
+			  "CONFIG0",
+			  "CONFIG1",
+			  "CONFIG2",
+			  "CONFIG3",
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "PWM0_OUT",
+			  "NC", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "PWM1_OUT",
+			  "HDMI_HPD_P",
+			  "SD_CARD_DET",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
 };
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
index e9b47b2..8b95832 100644
--- a/arch/arm/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -39,22 +39,21 @@
 	};
 
 	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+		brcm,pins = <4 5 7 8 9 10 11>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-
-	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
-		brcm,function = <BCM2835_FSEL_ALT3>;
-	};
 };
 
 &i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_gpio0>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_gpio2>;
 	status = "okay";
 	clock-frequency = <100000>;
 };
@@ -64,11 +63,21 @@
 };
 
 &sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
 	status = "okay";
 	bus-width = <4>;
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+};
+
 &pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
 };
 
@@ -84,3 +93,16 @@
 	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 	status = "okay";
 };
+
+&vec {
+	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
+	status = "okay";
+};
+
+&dsi0 {
+	power-domains = <&power RPI_POWER_DOMAIN_DSI0>;
+};
+
+&dsi1 {
+	power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
+};
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
index a78759e..659b6e9 100644
--- a/arch/arm/dts/bcm2835.dtsi
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -23,3 +23,13 @@
 		};
 	};
 };
+
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2835-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts
index 29e1cfe..e8de414 100644
--- a/arch/arm/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/dts/bcm2836-rpi-2-b.dts
@@ -2,6 +2,7 @@
 #include "bcm2836.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
@@ -26,7 +27,7 @@
 };
 
 &gpio {
-	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
@@ -38,3 +39,9 @@
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi
index 9d0651d..2c26d0b 100644
--- a/arch/arm/dts/bcm2836.dtsi
+++ b/arch/arm/dts/bcm2836.dtsi
@@ -36,6 +36,7 @@
 	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp";
 
 		v7_cpu0: cpu@0 {
 			device_type = "cpu";
@@ -76,3 +77,13 @@
 	interrupt-parent = <&local_intc>;
 	interrupts = <8>;
 };
+
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2836-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts
index 7841b72..20725ca 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b.dts
@@ -2,6 +2,7 @@
 #include "bcm2837.dtsi"
 #include "bcm2835-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@@ -15,16 +16,36 @@
 		act {
 			gpios = <&gpio 47 0>;
 		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 0>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
 	};
 };
 
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+};
+
+/* uart1 is mapped to the pin header */
 &uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
 	status = "okay";
+	bus-width = <4>;
 };
diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi
index 8216bbb..bc1cca5 100644
--- a/arch/arm/dts/bcm2837.dtsi
+++ b/arch/arm/dts/bcm2837.dtsi
@@ -1,7 +1,7 @@
 #include "bcm283x.dtsi"
 
 / {
-	compatible = "brcm,bcm2836";
+	compatible = "brcm,bcm2837";
 
 	soc {
 		ranges = <0x7e000000 0x3f000000 0x1000000>,
@@ -30,6 +30,7 @@
 	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
+		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
 		cpu0: cpu@0 {
 			device_type = "cpu";
@@ -74,3 +75,13 @@
 	interrupt-parent = <&local_intc>;
 	interrupts = <8>;
 };
+
+&cpu_thermal {
+	coefficients = <(-538)	412000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+	compatible = "brcm,bcm2837-thermal";
+	status = "okay";
+};
diff --git a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
index 12c981e..9a0599f 100644
--- a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
@@ -1,6 +1,6 @@
 / {
 	aliases {
-		ethernet = &ethernet;
+		ethernet0 = &ethernet;
 	};
 };
 
diff --git a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
index 3f0a56e..dc7ae77 100644
--- a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
@@ -1,6 +1,6 @@
 / {
 	aliases {
-		ethernet = &ethernet;
+		ethernet0 = &ethernet;
 	};
 };
 
diff --git a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
new file mode 100644
index 0000000..73f4ece
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
@@ -0,0 +1,3 @@
+&usb {
+	dr_mode = "host";
+};
diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi
index e5b4f20..05a6f48 100644
--- a/arch/arm/dts/bcm283x.dtsi
+++ b/arch/arm/dts/bcm283x.dtsi
@@ -3,6 +3,11 @@
 #include <dt-bindings/clock/bcm2835-aux.h>
 #include <dt-bindings/gpio/gpio.h>
 
+/* firmware-provided startup stubs live here, where the secondary CPUs are
+ * spinning.
+ */
+/memreserve/ 0x00000000 0x00001000;
+
 /* This include file covers the common peripherals and configuration between
  * bcm2835 and bcm2836 implementations, leaving the CPU configuration to
  * bcm2835.dtsi and bcm2836.dtsi.
@@ -19,6 +24,26 @@
 		bootargs = "earlyprintk console=ttyAMA0";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <80000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -93,10 +118,13 @@
 			#clock-cells = <1>;
 			reg = <0x7e101000 0x2000>;
 
-			/* CPRMAN derives everything from the platform's
-			 * oscillator.
+			/* CPRMAN derives almost everything from the
+			 * platform's oscillator.  However, the DSI
+			 * pixel clocks come from the DSI analog PHY.
 			 */
-			clocks = <&clk_osc>;
+			clocks = <&clk_osc>,
+				<&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
+				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 		};
 
 		rng@7e104000 {
@@ -104,7 +132,7 @@
 			reg = <0x7e104000 0x10>;
 		};
 
-		mailbox: mailbox@7e00b800 {
+		mailbox: mailbox@7e00b880 {
 			compatible = "brcm,bcm2835-mbox";
 			reg = <0x7e00b880 0x40>;
 			interrupts = <0 1>;
@@ -132,6 +160,213 @@
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			/* Defines pin muxing groups according to
+			 * BCM2835-ARM-Peripherals.pdf page 102.
+			 *
+			 * While each pin can have its mux selected
+			 * for various functions individually, some
+			 * groups only make sense to switch to a
+			 * particular function together.
+			 */
+			dpi_gpio0: dpi_gpio0 {
+				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+					     12 13 14 15 16 17 18 19
+					     20 21 22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			emmc_gpio22: emmc_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			emmc_gpio34: emmc_gpio34 {
+				brcm,pins = <34 35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP
+					     BCM2835_PUD_UP>;
+			};
+			emmc_gpio48: emmc_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			gpclk0_gpio4: gpclk0_gpio4 {
+				brcm,pins = <4>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio5: gpclk1_gpio5 {
+				brcm,pins = <5>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio42: gpclk1_gpio42 {
+				brcm,pins = <42>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk1_gpio44: gpclk1_gpio44 {
+				brcm,pins = <44>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio6: gpclk2_gpio6 {
+				brcm,pins = <6>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			gpclk2_gpio43: gpclk2_gpio43 {
+				brcm,pins = <43>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			i2c0_gpio0: i2c0_gpio0 {
+				brcm,pins = <0 1>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio28: i2c0_gpio28 {
+				brcm,pins = <28 29>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c0_gpio44: i2c0_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT1>;
+			};
+			i2c1_gpio2: i2c1_gpio2 {
+				brcm,pins = <2 3>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			i2c1_gpio44: i2c1_gpio44 {
+				brcm,pins = <44 45>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			i2c_slave_gpio18: i2c_slave_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+
+			jtag_gpio4: jtag_gpio4 {
+				brcm,pins = <4 5 6 12 13>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			jtag_gpio22: jtag_gpio22 {
+				brcm,pins = <22 23 24 25 26 27>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			pcm_gpio18: pcm_gpio18 {
+				brcm,pins = <18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pcm_gpio28: pcm_gpio28 {
+				brcm,pins = <28 29 30 31>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			pwm0_gpio12: pwm0_gpio12 {
+				brcm,pins = <12>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm0_gpio18: pwm0_gpio18 {
+				brcm,pins = <18>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm0_gpio40: pwm0_gpio40 {
+				brcm,pins = <40>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio13: pwm1_gpio13 {
+				brcm,pins = <13>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio19: pwm1_gpio19 {
+				brcm,pins = <19>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			pwm1_gpio41: pwm1_gpio41 {
+				brcm,pins = <41>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			pwm1_gpio45: pwm1_gpio45 {
+				brcm,pins = <45>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			sdhost_gpio48: sdhost_gpio48 {
+				brcm,pins = <48 49 50 51 52 53>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+
+			spi0_gpio7: spi0_gpio7 {
+				brcm,pins = <7 8 9 10 11>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi0_gpio35: spi0_gpio35 {
+				brcm,pins = <35 36 37 38 39>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			spi1_gpio16: spi1_gpio16 {
+				brcm,pins = <16 17 18 19 20 21>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+			spi2_gpio40: spi2_gpio40 {
+				brcm,pins = <40 41 42 43 44 45>;
+				brcm,function = <BCM2835_FSEL_ALT4>;
+			};
+
+			uart0_gpio14: uart0_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT0>;
+			};
+			/* Separate from the uart0_gpio14 group
+			 * because it conflicts with spi1_gpio16, and
+			 * people often run uart0 on the two pins
+			 * without flow control.
+			 */
+			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio32: uart0_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT3>;
+			};
+			uart0_gpio36: uart0_gpio36 {
+				brcm,pins = <36 37>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+				brcm,pins = <38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+
+			uart1_gpio14: uart1_gpio14 {
+				brcm,pins = <14 15>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+				brcm,pins = <16 17>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio32: uart1_gpio32 {
+				brcm,pins = <32 33>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+				brcm,pins = <30 31>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_gpio40: uart1_gpio40 {
+				brcm,pins = <40 41>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
+			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+				brcm,pins = <42 43>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
+			};
 		};
 
 		uart0: serial@7e201000 {
@@ -144,6 +379,16 @@
 			arm,primecell-periphid = <0x00241011>;
 		};
 
+		sdhost: mmc@7e202000 {
+			compatible = "brcm,bcm2835-sdhost";
+			reg = <0x7e202000 0x100>;
+			interrupts = <2 24>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>;
+			dmas = <&dma 13>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
 		i2s: i2s@7e203000 {
 			compatible = "brcm,bcm2835-i2s";
 			reg = <0x7e203000 0x20>,
@@ -187,6 +432,33 @@
 			interrupts = <2 14>; /* pwa1 */
 		};
 
+		dsi0: dsi@7e209000 {
+			compatible = "brcm,bcm2835-dsi0";
+			reg = <0x7e209000 0x78>;
+			interrupts = <2 4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			clocks = <&clocks BCM2835_PLLA_DSI0>,
+				 <&clocks BCM2835_CLOCK_DSI0E>,
+				 <&clocks BCM2835_CLOCK_DSI0P>;
+			clock-names = "phy", "escape", "pixel";
+
+			clock-output-names = "dsi0_byte",
+					     "dsi0_ddr2",
+					     "dsi0_ddr";
+
+		};
+
+		thermal: thermal@7e212000 {
+			compatible = "brcm,bcm2835-thermal";
+			reg = <0x7e212000 0x8>;
+			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
 		aux: aux@0x7e215000 {
 			compatible = "brcm,bcm2835-aux";
 			#clock-cells = <1>;
@@ -246,6 +518,26 @@
 			interrupts = <2 1>;
 		};
 
+		dsi1: dsi@7e700000 {
+			compatible = "brcm,bcm2835-dsi1";
+			reg = <0x7e700000 0x8c>;
+			interrupts = <2 12>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+
+			clocks = <&clocks BCM2835_PLLD_DSI1>,
+				 <&clocks BCM2835_CLOCK_DSI1E>,
+				 <&clocks BCM2835_CLOCK_DSI1P>;
+			clock-names = "phy", "escape", "pixel";
+
+			clock-output-names = "dsi1_byte",
+					     "dsi1_ddr2",
+					     "dsi1_ddr";
+
+			status = "disabled";
+		};
+
 		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e804000 0x1000>;
@@ -266,6 +558,14 @@
 			status = "disabled";
 		};
 
+		vec: vec@7e806000 {
+			compatible = "brcm,bcm2835-vec";
+			reg = <0x7e806000 0x1000>;
+			clocks = <&clocks BCM2835_CLOCK_VEC>;
+			interrupts = <2 27>;
+			status = "disabled";
+		};
+
 		pixelvalve@7e807000 {
 			compatible = "brcm,bcm2835-pixelvalve2";
 			reg = <0x7e807000 0x100>;
@@ -281,6 +581,8 @@
 			clocks = <&clocks BCM2835_PLLH_PIX>,
 				 <&clocks BCM2835_CLOCK_HSM>;
 			clock-names = "pixel", "hdmi";
+			dmas = <&dma 17>;
+			dma-names = "audio-rx";
 			status = "disabled";
 		};
 
@@ -290,6 +592,10 @@
 			interrupts = <1 9>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&clk_usb>;
+			clock-names = "otg";
+			phys = <&usbphy>;
+			phy-names = "usb2-phy";
 		};
 
 		v3d: v3d@7ec00000 {
@@ -316,7 +622,18 @@
 			clock-output-names = "osc";
 			clock-frequency = <19200000>;
 		};
+
+		clk_usb: clock@4 {
+			compatible = "fixed-clock";
+			reg = <4>;
+			#clock-cells = <0>;
+			clock-output-names = "otg";
+			clock-frequency = <480000000>;
+		};
+	};
 
+	usbphy: phy {
+		compatible = "usb-nop-xceiv";
 	};
 };