diff --git a/doc/README.m5475evb b/doc/README.m5475evb
index cec4fd0..37d1438 100644
--- a/doc/README.m5475evb
+++ b/doc/README.m5475evb
@@ -106,8 +106,8 @@
 CFG_I2C_OFFSET		-- define for I2C base address offset
 CFG_IMMR		-- define for MBAR offset
 
-CONFIG_PCI              -- define for PCI support
-CONFIG_PCI_PNP          -- define for Plug n play support
+CONFIG_PCI		-- define for PCI support
+CONFIG_PCI_PNP		-- define for Plug n play support
 CONFIG_SKIPPCI_HOSTBRIDGE	-- SKIP PCI Host bridge
 CFG_PCI_MEM_BUS		-- PCI memory logical offset
 CFG_PCI_MEM_PHYS	-- PCI memory physical offset
@@ -143,7 +143,7 @@
 3. COMPILATION
 ==============
 3.1	To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux
-        version) from codesourcery.com was used. Download it from:
+	version) from codesourcery.com was used. Download it from:
 	http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
 
 3.2 Compilation
@@ -206,68 +206,68 @@
 flashoffset = 0x00000000
 sramstart   = 0xF2000000
 sramsize    = 0x00001000
-mbar        = 0xF0000000
+mbar	    = 0xF0000000
 busfreq     = 133.333 MHz
-pcifreq     =      0 MHz
+pcifreq     =	   0 MHz
 ethaddr     = 00:E0:0C:BC:E5:60
 eth1addr    = 00:E0:0C:BC:E5:61
 ip_addr     = 192.162.1.2
 baudrate    = 115200 bps
 -> ?
-?       - alias for 'help'
+?	- alias for 'help'
 autoscr - run script from memory
-base    - print or set address offset
-bdinfo  - print Board Info structure
-boot    - boot default, i.e., run 'bootcmd'
-bootd   - boot default, i.e., run 'bootcmd'
+base	- print or set address offset
+bdinfo	- print Board Info structure
+boot	- boot default, i.e., run 'bootcmd'
+bootd	- boot default, i.e., run 'bootcmd'
 bootelf - Boot from an ELF image in memory
-bootm   - boot application image from memory
+bootm	- boot application image from memory
 bootp	- boot image via network using BootP/TFTP protocol
-bootvx  - Boot vxWorks from an ELF image
-cmp     - memory compare
+bootvx	- Boot vxWorks from an ELF image
+cmp	- memory compare
 coninfo - print console devices and information
-cp      - memory copy
-crc32   - checksum calculation
-dcache  - enable or disable data cache
-echo    - echo args to console
-erase   - erase FLASH memory
-flinfo  - print FLASH memory information
-go      - start application at address 'addr'
-help    - print online help
-icache  - enable or disable instruction cache
-icrc32  - checksum calculation
-iloop   - infinite loop on address range
-imd     - i2c memory display
-iminfo  - print header information for application image
-imls    - list all images found in flash
-imm     - i2c memory modify (auto-incrementing)
-imw     - memory write (fill)
-inm     - memory modify (constant address)
-iprobe  - probe to discover valid I2C chip addresses
+cp	- memory copy
+crc32	- checksum calculation
+dcache	- enable or disable data cache
+echo	- echo args to console
+erase	- erase FLASH memory
+flinfo	- print FLASH memory information
+go	- start application at address 'addr'
+help	- print online help
+icache	- enable or disable instruction cache
+icrc32	- checksum calculation
+iloop	- infinite loop on address range
+imd	- i2c memory display
+iminfo	- print header information for application image
+imls	- list all images found in flash
+imm	- i2c memory modify (auto-incrementing)
+imw	- memory write (fill)
+inm	- memory modify (constant address)
+iprobe	- probe to discover valid I2C chip addresses
 itest	- return true/false on integer compare
-loadb   - load binary file over serial line (kermit mode)
-loads   - load S-Record file over serial line
-loady   - load binary file over serial line (ymodem mode)
-loop    - infinite loop on address range
-md      - memory display
-mii     - MII utility commands
-mm      - memory modify (auto-incrementing)
-mtest   - simple RAM test
-mw      - memory write (fill)
+loadb	- load binary file over serial line (kermit mode)
+loads	- load S-Record file over serial line
+loady	- load binary file over serial line (ymodem mode)
+loop	- infinite loop on address range
+md	- memory display
+mii	- MII utility commands
+mm	- memory modify (auto-incrementing)
+mtest	- simple RAM test
+mw	- memory write (fill)
 nfs	- boot image via network using NFS protocol
-nm      - memory modify (constant address)
-pci     - list and access PCI Configuration Space
+nm	- memory modify (constant address)
+pci	- list and access PCI Configuration Space
 ping	- send ICMP ECHO_REQUEST to network host
 printenv- print environment variables
 protect - enable or disable FLASH write protection
 rarpboot- boot image via network using RARP/TFTP protocol
-reset   - Perform RESET of the CPU
-run     - run commands in an environment variable
+reset	- Perform RESET of the CPU
+run	- run commands in an environment variable
 saveenv - save environment variables to persistent storage
-setenv  - set environment variables
-sleep   - delay execution for some time
+setenv	- set environment variables
+sleep	- delay execution for some time
 tftpboot- boot image via network using TFTP protocol
-usb     - USB sub-system
+usb	- USB sub-system
 usbboot - boot from USB device
 version - print monitor version
 -> usb start