ARM: at91: dt: add dts files for sama5d3xek board
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
diff --git a/arch/arm/dts/sama5d3xmb_cmp.dtsi b/arch/arm/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..77f989c
--- /dev/null
+++ b/arch/arm/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,236 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ * Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+ compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &dbgu;
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@f0000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi0: spi@f0004000 {
+ dmas = <0>, <0>; /* Do not use DMA for spi0 */
+
+ spi_flash@0 {
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ ssc0: ssc@f0008000 {
+ atmel,clk-from-rk-pin;
+ };
+
+ /*
+ * i2c0 conflicts with ISI:
+ * disable it to allow the use of ISI
+ * can not enable audio when i2c0 disabled
+ */
+ i2c0: i2c@f0014000 {
+ wm8904: wm8904@1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck0>;
+ clock-names = "mclk";
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ ov2640: camera@0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+ /* use pck1 for the master clock of ov2640 */
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ usart1: serial@f0020000 {
+ dmas = <0>, <0>; /* Do not use DMA for usart1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ isi: isi@f0034000 {
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+
+ mmc1: mmc@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ adc0: adc@f8018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ status = "okay";
+ };
+
+ macb1: ethernet@f802c000 {
+ phy-mode = "rmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@1 {
+ /*interrupt-parent = <&pioE>;*/
+ /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+ reg = <1>;
+ };
+ };
+
+ pinctrl@fffff200 {
+ board {
+ pinctrl_gpio_keys: gpio_keys {
+ atmel,pins =
+ <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ atmel,pins =
+ <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+ };
+
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
+ };
+
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+ };
+ };
+ };
+
+ dbgu: serial@ffffee00 {
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb0: gadget@00500000 {
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D3EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+
+ status = "disabled";
+ };
+
+ /* Conflict with LCD pins */
+ gpio_keys {
+ compatible = "gpio-keys";
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+ };
+};