ppc4xx: Add T3COPR board support (PPC460GT based)
This patch adds support for the T3CORP board, based on the
AppliedMicro (APM) PPC460GT.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/t3corp/t3corp.c b/board/t3corp/t3corp.c
new file mode 100644
index 0000000..8ffa321
--- /dev/null
+++ b/board/t3corp/t3corp.c
@@ -0,0 +1,193 @@
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc440.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <i2c.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <asm/4xx_pcie.h>
+#include <asm/gpio.h>
+
+int board_early_init_f(void)
+{
+ /*
+ * Setup the interrupt controller polarities, triggers, etc.
+ */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+ mtdcr(UIC2ER, 0x00000000); /* disable all */
+ mtdcr(UIC2CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC3SR, 0xffffffff); /* clear all */
+ mtdcr(UIC3ER, 0x00000000); /* disable all */
+ mtdcr(UIC3CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC3PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC3TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC3VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC3SR, 0xffffffff); /* clear all */
+
+ /*
+ * Configure PFC (Pin Function Control) registers
+ * enable GPIO 49-63
+ * UART0: 4 pins
+ */
+ mtsdr(SDR0_PFC0, 0x00007fff);
+ mtsdr(SDR0_PFC1, 0x00040000);
+
+ /* Enable PCI host functionality in SDR0_PCI0 */
+ mtsdr(SDR0_PCI0, 0xe0000000);
+
+ mtsdr(SDR0_SRST1, 0); /* Pull AHB out of reset default=1 */
+
+ /* Setup PLB4-AHB bridge based on the system address map */
+ mtdcr(AHB_TOP, 0x8000004B);
+ mtdcr(AHB_BOT, 0x8000004B);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ char *s = getenv("serial#");
+
+ printf("Board: T3CORP");
+
+ if (s != NULL) {
+ puts(", serial# ");
+ puts(s);
+ }
+ putc('\n');
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ /*
+ * T3CORP has 64MBytes of NOR flash (Spansion 29GL512), but the
+ * boot EBC mapping only supports a maximum of 16MBytes
+ * (4.ff00.0000 - 4.ffff.ffff).
+ * To solve this problem, the flash has to get remapped to another
+ * EBC address which accepts bigger regions:
+ *
+ * 0xfn00.0000 -> 4.cn00.0000
+ */
+
+ /* Remap the NOR flash to 0xcn00.0000 ... 0xcfff.ffff */
+ mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L | EBC_BXCR_BS_64MB |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
+
+ /* Remove TLB entry of boot EBC mapping */
+ remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20);
+
+ /* Add TLB entry for 0xfn00.0000 -> 0x4.cn00.0000 */
+ program_tlb(CONFIG_SYS_FLASH_BASE_PHYS, CONFIG_SYS_FLASH_BASE,
+ CONFIG_SYS_FLASH_SIZE, TLB_WORD2_I_ENABLE);
+
+ /*
+ * Now accessing of the whole 64Mbytes of NOR flash at virtual address
+ * 0xfc00.0000 is possible
+ */
+
+ /*
+ * Clear potential errors resulting from auto-calibration.
+ * If not done, then we could get an interrupt later on when
+ * exceptions are enabled.
+ */
+ set_mcsr(get_mcsr());
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u32 sdr0_srst1 = 0;
+ u32 eth_cfg;
+
+ /*
+ * Set EMAC mode/configuration (GMII, SGMII, RGMII...).
+ * This is board specific, so let's do it here.
+ */
+ mfsdr(SDR0_ETH_CFG, eth_cfg);
+ /* disable SGMII mode */
+ eth_cfg &= ~(SDR0_ETH_CFG_SGMII2_ENABLE |
+ SDR0_ETH_CFG_SGMII1_ENABLE |
+ SDR0_ETH_CFG_SGMII0_ENABLE);
+ /* Set the for 2 RGMII mode */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
+ eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL;
+ eth_cfg &= ~SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
+ mtsdr(SDR0_ETH_CFG, eth_cfg);
+
+ /*
+ * The AHB Bridge core is held in reset after power-on or reset
+ * so enable it now
+ */
+ mfsdr(SDR0_SRST1, sdr0_srst1);
+ sdr0_srst1 &= ~SDR0_SRST1_AHB;
+ mtsdr(SDR0_SRST1, sdr0_srst1);
+
+ return 0;
+}
+
+int board_pcie_last(void)
+{
+ /*
+ * Only PCIe0 for now, PCIe1 hangs on this board
+ */
+ return 0;
+}
+
+/*
+ * Board specific WRDTR and CLKTR values used by the auto-
+ * calibration code (4xx_ibm_ddr2_autocalib.c).
+ */
+static struct sdram_timing board_scan_options[] = {
+ {1, 2},
+ {-1, -1}
+};
+
+struct sdram_timing *ddr_scan_option(struct sdram_timing *default_val)
+{
+ return board_scan_options;
+}