board/xilinx/zynqmp/zynqmp_kria.env

autoload=no
baudrate=115200
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
boot_net_usb_start=usb start
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_syslinux_conf=extlinux/extlinux.conf
bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00011:UNDI:003000;setenv bootp_arch 0xb;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;
bootcmd_jtag=echo JTAG: Trying to boot script at ${scriptaddr} && source ${scriptaddr}; echo JTAG: SCRIPT FAILED: continuing...;
bootcmd_mmc0=devnum=0; run mmc_boot
bootcmd_mmc1=devnum=1; run mmc_boot
bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi
bootcmd_usb0=devnum=0; run usb_boot
bootcmd_usb1=devnum=1; run usb_boot
bootcmd_usb2=devnum=2; run usb_boot
bootcmd_usb3=devnum=3; run usb_boot
bootcmd_usb4=devnum=4; run usb_boot
bootdelay=2
bootfstype=fat
bootm_low=0
bootm_size=0x80000000
distro_bootcmd=scsi_need_init=; for target in ${boot_targets}; do run bootcmd_${target}; done
efi_dtb_prefixes=/ /dtb/ /dtb/current/
fdt_addr_r=0x40000000
fdt_high=0x10000000
fileaddr=0x18000000
initrd_high=0x79000000
kernel_addr_r=0x18000000
load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
mmc_boot=if mmc dev ${devnum}; then devtype=mmc; run scan_dev_for_boot_part; fi
pxefile_addr_r=0x10000000
ramdisk_addr_r=0x02100000
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done; setenv devplist
scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
script_offset_f=0x3e80000
script_size_f=0x80000
scriptaddr=0x20000000
usb_boot=usb start; if usb dev ${devnum}; then devtype=usb; run scan_dev_for_boot_part; fi
preboot=setenv boot_targets; setenv modeboot; run board_setup

# SOM specific boot methods
usb_boot_devices='usb0 usb1 usb2 usb3 usb4'
som_cc_boot=if test ${card1_name} = SCK-KV-G; then setenv boot_targets mmc1 ${usb_boot_devices} pxe dhcp jtag && run distro_bootcmd; elif test ${card1_name} = SCK-KR-G; then setenv boot_targets ${usb_boot_devices} pxe dhcp jtag && run distro_bootcmd; else test ${card1_name} = SCK-KD-G; setenv boot_targets ${usb_boot_devices} pxe dhcp jtag && run distro_bootcmd; fi;"
som_mmc_boot=setenv boot_targets mmc0 && run distro_bootcmd

# To disable bootmenu set enable_bootmenu=0
enable_bootmenu=1
som_bootmenu=if test ${enable_bootmenu} = 1; then bootmenu; else run som_mmc_boot; fi

k26_starter=SMK-K26-XCL2G
k24_starter=SMK-K24-XCL2G
bootcmd=setenv model $board_name; setexpr model gsub ".*${k24_starter}.*" starter; setexpr model gsub ".*${k26_starter}.*" starter; if test ${model} = "starter"; then run som_cc_boot; else run som_bootmenu; fi

# Boot menu
bootmenu_0=eMMC Boot=run som_mmc_boot
bootmenu_1=SD Boot=run som_cc_boot
bootmenu_delay=5

usb_hub_init=mw 1000 0056 && sleep 1 && i2c write 1000 2d aa 2 -s

# usb hub init
kv260_setup=i2c dev 1 && run usb_hub_init
# usb hub init
kr260_setup=i2c dev 1 && run usb_hub_init; i2c dev 2 && run usb_hub_init;
# usb hub init with enabling PM nodes for ...
kd240_setup=i2c dev 1 && run usb_hub_init;zynqmp pmufw node 33; zynqmp pmufw node 47

tpm_setup=tpm autostart;
tpm_reset=echo "!!! For TPM reset a full power cycle or pressing the POR_B button is required !!!";
tpm_kv260=if test ${card1_rev} = A -o ${card1_rev} = B -o ${card1_rev} = Y -o ${card1_rev} = Z -o ${card1_rev} = 1; then run tpm_reset; fi
tpm_kd240=if test ${card1_rev} = A; then run tpm_reset; fi

board_setup=\
rtc dev 0; \
zynqmp mmio_write 0xFFCA0010 0xfff 0; \
if test ${card1_name} = SCK-KV-G; then run kv260_setup; run tpm_kv260; fi;\
if test ${card1_name} = SCK-KR-G; then run kr260_setup; run tpm_reset; fi;\
if test ${card1_name} = SCK-KD-G; then run kd240_setup; run tpm_kd240; fi;\
run tpm_setup