imx8mm-phg: Add board support
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3ecd6a8..48de9ab 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -960,6 +960,7 @@
imx8mm-kontron-bl.dtb \
imx8mm-kontron-bl-osm-s.dtb \
imx8mm-mx8menlo.dtb \
+ imx8mm-phg.dtb \
imx8mm-venice.dtb \
imx8mm-venice-gw71xx-0x.dtb \
imx8mm-venice-gw72xx-0x.dtb \
diff --git a/arch/arm/dts/imx8mm-phg-u-boot.dtsi b/arch/arm/dts/imx8mm-phg-u-boot.dtsi
new file mode 100644
index 0000000..3bf45ef
--- /dev/null
+++ b/arch/arm/dts/imx8mm-phg-u-boot.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include "imx8mm-u-boot.dtsi"
+
+/ {
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ u-boot,dm-spl;
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+};
+
+&aips4 {
+ u-boot,dm-spl;
+};
+
+®_usdhc2_vmmc {
+ u-boot,off-on-delay-us = <20000>;
+};
+
+&pinctrl_reg_usdhc2_vmmc {
+ u-boot,dm-spl;
+};
+
+&pinctrl_uart2 {
+ u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2_gpio {
+ u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2 {
+ u-boot,dm-spl;
+};
+
+&pinctrl_usdhc3 {
+ u-boot,dm-spl;
+};
+
+&gpio1 {
+ u-boot,dm-spl;
+};
+
+&gpio2 {
+ u-boot,dm-spl;
+};
+
+&gpio3 {
+ u-boot,dm-spl;
+};
+
+&gpio4 {
+ u-boot,dm-spl;
+};
+
+&gpio5 {
+ u-boot,dm-spl;
+};
+
+&uart2 {
+ u-boot,dm-spl;
+};
+
+&usbmisc1 {
+ u-boot,dm-spl;
+};
+
+&usbphynop1 {
+ u-boot,dm-spl;
+};
+
+&usbotg1 {
+ u-boot,dm-spl;
+};
+
+&usdhc1 {
+ u-boot,dm-spl;
+};
+
+&usdhc2 {
+ u-boot,dm-spl;
+ sd-uhs-sdr104;
+ sd-uhs-ddr50;
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+ assigned-clock-rates = <400000000>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_400M>;
+};
+
+&usdhc3 {
+ u-boot,dm-spl;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ /*
+ * prevents voltage switch warn: driver will switch even at
+ * fixed voltage
+ */
+ /delete-property/ vmmc-supply;
+ /delete-property/ vqmmc-supply;
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+ assigned-clock-rates = <400000000>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_400M>;
+};
+
+&i2c1 {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@30800000/i2c@30a20000/pmic@25} {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@30800000/i2c@30a20000/pmic@25/regulators} {
+ u-boot,dm-spl;
+};
+
+&pinctrl_i2c1 {
+ u-boot,dm-spl;
+};
+
+&pinctrl_pmic {
+ u-boot,dm-spl;
+};
+
+&wdog1 {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/imx8mm-phg.dts b/arch/arm/dts/imx8mm-phg.dts
new file mode 100644
index 0000000..e944773
--- /dev/null
+++ b/arch/arm/dts/imx8mm-phg.dts
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Fabio Estevam <festevam@denx.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+
+/ {
+ model = "Cloos i.MX8MM PHG board";
+ compatible = "cloos,imx8mm-phg", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ aliases {
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ beeper {
+ compatible = "gpio-beeper";
+ pinctrl-0 = <&pinctrl_beeper>;
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_led>;
+
+ led-0 {
+ label = "status1";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "status2";
+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "status3";
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-3 {
+ label = "run";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "powerled";
+ gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_otg_vbus_ctrl>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbphynop1 {
+ power-domains = <&pgc_otg1>;
+};
+
+&usbphynop2 {
+ power-domains = <&pgc_otg2>;
+};
+
+&usbotg1 {
+ dr_mode = "host";
+ vbus-supply = <®_usb_otg_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc2 {
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+ assigned-clock-rates = <400000000>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_400M>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-mmc;
+ no-sdio;
+ sd-uhs-sdr104;
+ sd-uhs-ddr50;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_beeper: beepergrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x19
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
+ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x10
+ >;
+ };
+
+ pinctrl_gpio_led: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19
+ MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_otg_vbus_ctrl: otgvbusctrlgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_DATA0_GPIO2_IO2 0x119
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx8mm-tqma8mqml.dtsi b/arch/arm/dts/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 0000000..f649dfa
--- /dev/null
+++ b/arch/arm/dts/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mm.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+ compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* identical to buck4_reg, but should never change */
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&gpu_2d {
+ status = "okay";
+};
+
+&gpu_3d {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM / VPU */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&pcie_phy {
+ fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+ fsl,clkreq-unsupported;
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82>,
+ <MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82>;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004>,
+ <MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004>;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004>,
+ <MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004>;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94>;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84>;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84>;
+ };
+};
diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
index a0715e8..64e6b49 100644
--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
@@ -94,6 +94,13 @@
select SUPPORT_SPL
select IMX8M_LPDDR4
+config TARGET_IMX8MM_PHG
+ bool "i.MX8MM PHG board"
+ select BINMAN
+ select IMX8MM
+ select SUPPORT_SPL
+ select IMX8M_LPDDR4
+
config TARGET_IMX8MM_VENICE
bool "Support Gateworks Venice iMX8M Mini module"
select BINMAN
@@ -305,6 +312,7 @@
source "board/beacon/imx8mm/Kconfig"
source "board/beacon/imx8mn/Kconfig"
source "board/bsh/imx8mn_smm_s2/Kconfig"
+source "board/cloos/imx8mm_phg/Kconfig"
source "board/compulab/imx8mm-cl-iot-gate/Kconfig"
source "board/data_modul/imx8mm_edm_sbc/Kconfig"
source "board/dhelectronics/dh_imx8mp/Kconfig"