if ROCKCHIP_PX30

config TARGET_EVB_PX30
	bool "EVB_PX30"
	help
	  This target config option used for below listed px30 boards.

	  EVB_PX30:
	  * EVB_PX30 is an evaluation board for Rockchip PX30.

config TARGET_ODROID_GO2
	bool "ODROID_GO2"

config TARGET_PX30_CORE
	bool "Engicam PX30.Core"
	help
	  PX30.Core EDIMM2.2:
	  * PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
	  * EDIMM2.2 is a Form Factor Capacitive Evaluation Board from Engicam.
	  * PX30.Core needs to mount on top of EDIMM2.2 for creating complete
	    PX30.Core EDIMM2.2 Starter Kit.

	  PX30.Core CTOUCH2:
	  * PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
	  * CTOUCH2.0 is a general purpose Carrier board with capacitive
	    touch interface support.
	  * PX30.Core needs to mount on top of CTOUCH2.0 for creating complete
	    PX30.Core C.TOUCH Carrier board.

	  PX30.Core CTOUCH2-OF10:
	  * PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
	  * CTOUCH2.0 is a general purpose Carrier board with capacitive
	    touch interface support.
	  * 10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
	  * PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
            10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.

config TARGET_RINGNECK_PX30
	bool "Theobroma Systems PX30-uQ7 (Ringneck)"
	help
	  The PX30-uQ7 (Ringneck) SoM is a uQseven-compatible (40mmx70mm,
          MXM-230 connector) system-on-module from Theobroma Systems[1],
	  featuring the Rockchip PX30.

	  It provides the following feature set:
	    * up to 4GB DDR4
	    * up to 128GB on-module eMMC (with 8-bit 1.8V interface)
	    * SD card (on a baseboard) via edge connector
	    * Fast Ethernet with on-module TI DP83825I PHY
	    * MIPI-DSI/LVDS
	    * MIPI-CSI
	    * USB
	      - 1x USB 2.0 dual-role
	      - 3x USB 2.0 host
	    * on-module companion controller (STM32 Cortex-M0 or ATtiny), implementing:
	      - low-power RTC functionality (ISL1208 emulation)
	      - fan controller (AMC6821 emulation)
	      - USB<->CAN bridge controller (STM32 only)
	    * on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
	    * on-module NXP SE05x Secure Element

config ROCKCHIP_BOOT_MODE_REG
	default 0xff010200

config ROCKCHIP_STIMER_BASE
	default 0xff220020

config SYS_SOC
	default "px30"

config SYS_MALLOC_F_LEN
	default 0x400

config SPL_SERIAL
	default y

config TPL_LDSCRIPT
	default "arch/arm/mach-rockchip/u-boot-tpl-v8.lds"

config TPL_TEXT_BASE
	default 0xff0e1000

config TPL_STACK
	default 0xff0e4fff

config TPL_SYS_MALLOC_F_LEN
	default 0x600

config DEBUG_UART_CHANNEL
	int "Mux channel to use for debug UART2/UART3"
	depends on DEBUG_UART_BOARD_INIT
	default 0
	help
	  UART2 and UART3 can use two different set of pins to route the output.
	  For using the UART for early debugging the route to use needs
	  to be declared (0 or 1).

source "board/engicam/px30_core/Kconfig"
source "board/hardkernel/odroid_go2/Kconfig"
source "board/rockchip/evb_px30/Kconfig"
source "board/theobroma-systems/ringneck_px30/Kconfig"

endif