cmd: ti: Generalize cmd_ddr3 command
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/cmd/ti/ddr3.c b/cmd/ti/ddr3.c
index b6435a4..664bb5f 100644
--- a/cmd/ti/ddr3.c
+++ b/cmd/ti/ddr3.c
@@ -7,12 +7,15 @@
*/
#include <asm/arch/hardware.h>
-#include <asm/arch/ddr3.h>
+#include <asm/cache.h>
+#include <asm/emif.h>
#include <common.h>
#include <command.h>
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_ARCH_KEYSTONE
+#include <asm/arch/ddr3.h>
#define DDR_MIN_ADDR CONFIG_SYS_SDRAM_BASE
#define STACKSIZE (512 << 10) /* 512 KiB */
@@ -21,6 +24,7 @@
#define ECC_END_ADDR1 (((gd->start_addr_sp - DDR_REMAP_ADDR - \
STACKSIZE) >> 17) - 2)
+#endif
#define DDR_TEST_BURST_SIZE 1024
@@ -153,57 +157,143 @@
return 0;
}
-static int ddr_memory_ecc_err(u32 base, u32 address, u32 ecc_err)
+static void ddr_check_ecc_status(void)
{
- u32 value1, value2, value3;
+ struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+ u32 err_1b = readl(&emif->emif_1b_ecc_err_cnt);
+ u32 int_status = readl(&emif->emif_irqstatus_raw_sys);
+ int ecc_test = 0;
+ char *env;
+
+ env = env_get("ecc_test");
+ if (env)
+ ecc_test = simple_strtol(env, NULL, 0);
+
+ puts("ECC test Status:\n");
+ if (int_status & EMIF_INT_WR_ECC_ERR_SYS_MASK)
+ puts("\tECC test: DDR ECC write error interrupted\n");
- puts("Disabling DDR ECC ...\n");
- ddr3_disable_ecc(base);
+ if (int_status & EMIF_INT_TWOBIT_ECC_ERR_SYS_MASK)
+ if (!ecc_test)
+ panic("\tECC test: DDR ECC 2-bit error interrupted");
- value1 = __raw_readl(address);
- value2 = value1 ^ ecc_err;
- __raw_writel(value2, address);
+ if (int_status & EMIF_INT_ONEBIT_ECC_ERR_SYS_MASK)
+ puts("\tECC test: DDR ECC 1-bit error interrupted\n");
- value3 = __raw_readl(address);
- printf("ECC err test, addr 0x%x, read data 0x%x, wrote data 0x%x, err pattern: 0x%x, read after write data 0x%x\n",
- address, value1, value2, ecc_err, value3);
+ if (err_1b)
+ printf("\tECC test: 1-bit ECC err count: 0x%x\n", err_1b);
+}
+
+static int ddr_memory_ecc_err(u32 addr, u32 ecc_err)
+{
+ struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+ u32 ecc_ctrl = readl(&emif->emif_ecc_ctrl_reg);
+ u32 val1, val2, val3;
+
+ debug("Disabling D-Cache before ECC test\n");
+ dcache_disable();
+ invalidate_dcache_all();
- __raw_writel(ECC_START_ADDR1 | (ECC_END_ADDR1 << 16),
- base + KS2_DDR3_ECC_ADDR_RANGE1_OFFSET);
+ puts("Testing DDR ECC:\n");
+ puts("\tECC test: Disabling DDR ECC ...\n");
+ writel(0, &emif->emif_ecc_ctrl_reg);
- puts("Enabling DDR ECC ...\n");
- ddr3_enable_ecc(base, 1);
+ val1 = readl(addr);
+ val2 = val1 ^ ecc_err;
+ writel(val2, addr);
- value1 = __raw_readl(address);
- printf("ECC err test, addr 0x%x, read data 0x%x\n", address, value1);
+ val3 = readl(addr);
+ printf("\tECC test: addr 0x%x, read data 0x%x, written data 0x%x, err pattern: 0x%x, read after write data 0x%x\n",
+ addr, val1, val2, ecc_err, val3);
- ddr3_check_ecc_int(base);
+ puts("\tECC test: Enabling DDR ECC ...\n");
+#ifdef CONFIG_ARCH_KEYSTONE
+ ecc_ctrl = ECC_START_ADDR1 | (ECC_END_ADDR1 << 16);
+ writel(ecc_ctrl, EMIF1_BASE + KS2_DDR3_ECC_ADDR_RANGE1_OFFSET);
+ ddr3_enable_ecc(EMIF1_BASE, 1);
+#else
+ writel(ecc_ctrl, &emif->emif_ecc_ctrl_reg);
+#endif
+
+ val1 = readl(addr);
+ printf("\tECC test: addr 0x%x, read data 0x%x\n", addr, val1);
+
+ ddr_check_ecc_status();
+
+ debug("Enabling D-cache back after ECC test\n");
+ enable_caches();
+
return 0;
}
+static int is_addr_valid(u32 addr)
+{
+ struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+ u32 start_addr, end_addr, range, ecc_ctrl;
+
+#ifdef CONFIG_ARCH_KEYSTONE
+ ecc_ctrl = EMIF_ECC_REG_ECC_ADDR_RGN_1_EN_MASK;
+ range = ECC_START_ADDR1 | (ECC_END_ADDR1 << 16);
+#else
+ ecc_ctrl = readl(&emif->emif_ecc_ctrl_reg);
+ range = readl(&emif->emif_ecc_address_range_1);
+#endif
+
+ /* Check in ecc address range 1 */
+ if (ecc_ctrl & EMIF_ECC_REG_ECC_ADDR_RGN_1_EN_MASK) {
+ start_addr = ((range & EMIF_ECC_REG_ECC_START_ADDR_MASK) << 16)
+ + CONFIG_SYS_SDRAM_BASE;
+ end_addr = start_addr + (range & EMIF_ECC_REG_ECC_END_ADDR_MASK)
+ + 0xFFFF;
+ if ((addr >= start_addr) && (addr <= end_addr))
+ /* addr within ecc address range 1 */
+ return 1;
+ }
+
+ /* Check in ecc address range 2 */
+ if (ecc_ctrl & EMIF_ECC_REG_ECC_ADDR_RGN_2_EN_MASK) {
+ range = readl(&emif->emif_ecc_address_range_2);
+ start_addr = ((range & EMIF_ECC_REG_ECC_START_ADDR_MASK) << 16)
+ + CONFIG_SYS_SDRAM_BASE;
+ end_addr = start_addr + (range & EMIF_ECC_REG_ECC_END_ADDR_MASK)
+ + 0xFFFF;
+ if ((addr >= start_addr) && (addr <= end_addr))
+ /* addr within ecc address range 2 */
+ return 1;
+ }
+
+ return 0;
+}
+
+static int is_ecc_enabled(void)
+{
+ struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+ u32 ecc_ctrl = readl(&emif->emif_ecc_ctrl_reg);
+
+ return (ecc_ctrl & EMIF_ECC_CTRL_REG_ECC_EN_MASK) &&
+ (ecc_ctrl & EMIF_ECC_REG_RMW_EN_MASK);
+}
+
static int do_ddr_test(cmd_tbl_t *cmdtp,
int flag, int argc, char * const argv[])
{
u32 start_addr, end_addr, size, ecc_err;
if ((argc == 4) && (strncmp(argv[1], "ecc_err", 8) == 0)) {
- if (!ddr3_ecc_support_rmw(KS2_DDR3A_EMIF_CTRL_BASE)) {
- puts("ECC RMW isn't supported for this SOC\n");
- return 1;
+ if (!is_ecc_enabled()) {
+ puts("ECC not enabled. Please Enable ECC any try again\n");
+ return CMD_RET_FAILURE;
}
start_addr = simple_strtoul(argv[2], NULL, 16);
ecc_err = simple_strtoul(argv[3], NULL, 16);
- if ((start_addr < CONFIG_SYS_SDRAM_BASE) ||
- (start_addr > (CONFIG_SYS_SDRAM_BASE +
- CONFIG_MAX_RAM_BANK_SIZE - 1))) {
- puts("Invalid address!\n");
- return cmd_usage(cmdtp);
+ if (!is_addr_valid(start_addr)) {
+ puts("Invalid address. Please enter ECC supported address!\n");
+ return CMD_RET_FAILURE;
}
- ddr_memory_ecc_err(KS2_DDR3A_EMIF_CTRL_BASE,
- start_addr, ecc_err);
+ ddr_memory_ecc_err(start_addr, ecc_err);
return 0;
}
@@ -216,10 +306,10 @@
if ((start_addr < CONFIG_SYS_SDRAM_BASE) ||
(start_addr > (CONFIG_SYS_SDRAM_BASE +
- CONFIG_MAX_RAM_BANK_SIZE - 1)) ||
+ get_effective_memsize() - 1)) ||
(end_addr < CONFIG_SYS_SDRAM_BASE) ||
(end_addr > (CONFIG_SYS_SDRAM_BASE +
- CONFIG_MAX_RAM_BANK_SIZE - 1)) || (start_addr >= end_addr)) {
+ get_effective_memsize() - 1)) || (start_addr >= end_addr)) {
puts("Invalid start or end address!\n");
return cmd_usage(cmdtp);
}