OMAP3+: introduce generic ABB support
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:
* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
performance at the cost of power. Used to operate safely at high
OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
save power. Used to save power at lower OPPs.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
diff --git a/arch/arm/cpu/armv7/omap5/Makefile b/arch/arm/cpu/armv7/omap5/Makefile
index ce00e2c..6ff8dbb 100644
--- a/arch/arm/cpu/armv7/omap5/Makefile
+++ b/arch/arm/cpu/armv7/omap5/Makefile
@@ -30,6 +30,7 @@
COBJS += sdram.o
COBJS += prcm-regs.o
COBJS += hw_data.o
+COBJS += abb.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
diff --git a/arch/arm/cpu/armv7/omap5/abb.c b/arch/arm/cpu/armv7/omap5/abb.c
new file mode 100644
index 0000000..92470be
--- /dev/null
+++ b/arch/arm/cpu/armv7/omap5/abb.c
@@ -0,0 +1,67 @@
+/*
+ *
+ * Adaptive Body Bias programming sequence for OMAP5 family
+ *
+ * (C) Copyright 2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/omap_common.h>
+#include <asm/io.h>
+
+/*
+ * Setup LDOVBB for OMAP5.
+ * On OMAP5+ some ABB settings are fused. They are handled
+ * in the following way:
+ *
+ * 1. corresponding EFUSE register contains ABB enable bit
+ * and VSET value
+ * 2. If ABB enable bit is set to 1, than ABB should be
+ * enabled, otherwise ABB should be disabled
+ * 3. If ABB is enabled, than VSET value should be copied
+ * to corresponding MUX control register
+ */
+s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb)
+{
+ u32 vset;
+
+ /*
+ * ABB parameters must be properly fused
+ * otherwise ABB should be disabled
+ */
+ vset = readl(fuse);
+ if (!(vset & OMAP5_ABB_FUSE_ENABLE_MASK))
+ return -1;
+
+ /* prepare VSET value for LDOVBB mux register */
+ vset &= OMAP5_ABB_FUSE_VSET_MASK;
+ vset >>= ffs(OMAP5_ABB_FUSE_VSET_MASK) - 1;
+ vset <<= ffs(OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK) - 1;
+ vset |= OMAP5_ABB_LDOVBBMPU_MUX_CTRL_MASK;
+
+ /* setup LDOVBB using fused value */
+ clrsetbits_le32(ldovbb, OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK, vset);
+
+ return 0;
+}