board: sama5d2_xplained: clean up macb init code
Because the MACB driver supports the driver model and device tree,
the pins configuration and clock enabling are handled by the
pinctrl driver and clock driver, remove this hardcoded init code.
The USB Ether init code is removed as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
diff --git a/board/atmel/sama5d2_xplained/sama5d2_xplained.c b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
index c5337af..5f38ebc 100644
--- a/board/atmel/sama5d2_xplained/sama5d2_xplained.c
+++ b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
@@ -12,15 +12,12 @@
#include <i2c.h>
#include <lcd.h>
#include <mmc.h>
-#include <net.h>
-#include <netdev.h>
#include <spi.h>
#include <version.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/atmel_pio4.h>
#include <asm/arch/atmel_mpddrc.h>
-#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/atmel_sdhci.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
@@ -118,22 +115,6 @@
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */
-static void board_gmac_hw_init(void)
-{
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 14, 0); /* GTXCK */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 15, 0); /* GTXEN */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 16, 0); /* GRXDV */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 17, 0); /* GRXER */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 18, 0); /* GRX0 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 19, 0); /* GRX1 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 20, 0); /* GTX0 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 21, 0); /* GTX1 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 22, 0); /* GMDC */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 23, 0); /* GMDIO */
-
- at91_periph_clk_enable(ATMEL_ID_GMAC);
-}
-
static void board_uart1_hw_init(void)
{
atmel_pio4_set_a_periph(AT91_PIO_PORTD, 2, 1); /* URXD1 */
@@ -167,18 +148,12 @@
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_MACB
- board_gmac_hw_init();
-#endif
#ifdef CONFIG_LCD
board_lcd_hw_init();
#endif
#ifdef CONFIG_CMD_USB
board_usb_hw_init();
#endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- at91_udp_hw_init();
-#endif
return 0;
}
@@ -190,24 +165,6 @@
return 0;
}
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
-#endif
-
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- usba_udc_probe(&pdata);
-#ifdef CONFIG_USB_ETH_RNDIS
- usb_eth_initialize(bis);
-#endif
-#endif
-
- return rc;
-}
-
#ifdef CONFIG_CMD_I2C
static int set_ethaddr_from_eeprom(void)
{