mtd: move NAND files into a raw/ subdirectory
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
diff --git a/drivers/mtd/nand/raw/pxa3xx_nand.c b/drivers/mtd/nand/raw/pxa3xx_nand.c
new file mode 100644
index 0000000..4c783f1
--- /dev/null
+++ b/drivers/mtd/nand/raw/pxa3xx_nand.c
@@ -0,0 +1,1828 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * drivers/mtd/nand/raw/pxa3xx_nand.c
+ *
+ * Copyright © 2005 Intel Corporation
+ * Copyright © 2006 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <fdtdec.h>
+#include <nand.h>
+#include <linux/errno.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/types.h>
+
+#include "pxa3xx_nand.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define TIMEOUT_DRAIN_FIFO 5 /* in ms */
+#define CHIP_DELAY_TIMEOUT 200
+#define NAND_STOP_DELAY 40
+
+/*
+ * Define a buffer size for the initial command that detects the flash device:
+ * STATUS, READID and PARAM.
+ * ONFI param page is 256 bytes, and there are three redundant copies
+ * to be read. JEDEC param page is 512 bytes, and there are also three
+ * redundant copies to be read.
+ * Hence this buffer should be at least 512 x 3. Let's pick 2048.
+ */
+#define INIT_BUFFER_SIZE 2048
+
+/* registers and bit definitions */
+#define NDCR (0x00) /* Control register */
+#define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */
+#define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */
+#define NDSR (0x14) /* Status Register */
+#define NDPCR (0x18) /* Page Count Register */
+#define NDBDR0 (0x1C) /* Bad Block Register 0 */
+#define NDBDR1 (0x20) /* Bad Block Register 1 */
+#define NDECCCTRL (0x28) /* ECC control */
+#define NDDB (0x40) /* Data Buffer */
+#define NDCB0 (0x48) /* Command Buffer0 */
+#define NDCB1 (0x4C) /* Command Buffer1 */
+#define NDCB2 (0x50) /* Command Buffer2 */
+
+#define NDCR_SPARE_EN (0x1 << 31)
+#define NDCR_ECC_EN (0x1 << 30)
+#define NDCR_DMA_EN (0x1 << 29)
+#define NDCR_ND_RUN (0x1 << 28)
+#define NDCR_DWIDTH_C (0x1 << 27)
+#define NDCR_DWIDTH_M (0x1 << 26)
+#define NDCR_PAGE_SZ (0x1 << 24)
+#define NDCR_NCSX (0x1 << 23)
+#define NDCR_ND_MODE (0x3 << 21)
+#define NDCR_NAND_MODE (0x0)
+#define NDCR_CLR_PG_CNT (0x1 << 20)
+#define NFCV1_NDCR_ARB_CNTL (0x1 << 19)
+#define NDCR_RD_ID_CNT_MASK (0x7 << 16)
+#define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK)
+
+#define NDCR_RA_START (0x1 << 15)
+#define NDCR_PG_PER_BLK (0x1 << 14)
+#define NDCR_ND_ARB_EN (0x1 << 12)
+#define NDCR_INT_MASK (0xFFF)
+
+#define NDSR_MASK (0xfff)
+#define NDSR_ERR_CNT_OFF (16)
+#define NDSR_ERR_CNT_MASK (0x1f)
+#define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK)
+#define NDSR_RDY (0x1 << 12)
+#define NDSR_FLASH_RDY (0x1 << 11)
+#define NDSR_CS0_PAGED (0x1 << 10)
+#define NDSR_CS1_PAGED (0x1 << 9)
+#define NDSR_CS0_CMDD (0x1 << 8)
+#define NDSR_CS1_CMDD (0x1 << 7)
+#define NDSR_CS0_BBD (0x1 << 6)
+#define NDSR_CS1_BBD (0x1 << 5)
+#define NDSR_UNCORERR (0x1 << 4)
+#define NDSR_CORERR (0x1 << 3)
+#define NDSR_WRDREQ (0x1 << 2)
+#define NDSR_RDDREQ (0x1 << 1)
+#define NDSR_WRCMDREQ (0x1)
+
+#define NDCB0_LEN_OVRD (0x1 << 28)
+#define NDCB0_ST_ROW_EN (0x1 << 26)
+#define NDCB0_AUTO_RS (0x1 << 25)
+#define NDCB0_CSEL (0x1 << 24)
+#define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29)
+#define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK)
+#define NDCB0_CMD_TYPE_MASK (0x7 << 21)
+#define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK)
+#define NDCB0_NC (0x1 << 20)
+#define NDCB0_DBC (0x1 << 19)
+#define NDCB0_ADDR_CYC_MASK (0x7 << 16)
+#define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK)
+#define NDCB0_CMD2_MASK (0xff << 8)
+#define NDCB0_CMD1_MASK (0xff)
+#define NDCB0_ADDR_CYC_SHIFT (16)
+
+#define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */
+#define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */
+#define EXT_CMD_TYPE_READ 4 /* Read */
+#define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */
+#define EXT_CMD_TYPE_FINAL 3 /* Final command */
+#define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */
+#define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */
+
+/*
+ * This should be large enough to read 'ONFI' and 'JEDEC'.
+ * Let's use 7 bytes, which is the maximum ID count supported
+ * by the controller (see NDCR_RD_ID_CNT_MASK).
+ */
+#define READ_ID_BYTES 7
+
+/* macros for registers read/write */
+#define nand_writel(info, off, val) \
+ writel((val), (info)->mmio_base + (off))
+
+#define nand_readl(info, off) \
+ readl((info)->mmio_base + (off))
+
+/* error code and state */
+enum {
+ ERR_NONE = 0,
+ ERR_DMABUSERR = -1,
+ ERR_SENDCMD = -2,
+ ERR_UNCORERR = -3,
+ ERR_BBERR = -4,
+ ERR_CORERR = -5,
+};
+
+enum {
+ STATE_IDLE = 0,
+ STATE_PREPARED,
+ STATE_CMD_HANDLE,
+ STATE_DMA_READING,
+ STATE_DMA_WRITING,
+ STATE_DMA_DONE,
+ STATE_PIO_READING,
+ STATE_PIO_WRITING,
+ STATE_CMD_DONE,
+ STATE_READY,
+};
+
+enum pxa3xx_nand_variant {
+ PXA3XX_NAND_VARIANT_PXA,
+ PXA3XX_NAND_VARIANT_ARMADA370,
+};
+
+struct pxa3xx_nand_host {
+ struct nand_chip chip;
+ void *info_data;
+
+ /* page size of attached chip */
+ int use_ecc;
+ int cs;
+
+ /* calculated from pxa3xx_nand_flash data */
+ unsigned int col_addr_cycles;
+ unsigned int row_addr_cycles;
+};
+
+struct pxa3xx_nand_info {
+ struct nand_hw_control controller;
+ struct pxa3xx_nand_platform_data *pdata;
+
+ struct clk *clk;
+ void __iomem *mmio_base;
+ unsigned long mmio_phys;
+ int cmd_complete, dev_ready;
+
+ unsigned int buf_start;
+ unsigned int buf_count;
+ unsigned int buf_size;
+ unsigned int data_buff_pos;
+ unsigned int oob_buff_pos;
+
+ unsigned char *data_buff;
+ unsigned char *oob_buff;
+
+ struct pxa3xx_nand_host *host[NUM_CHIP_SELECT];
+ unsigned int state;
+
+ /*
+ * This driver supports NFCv1 (as found in PXA SoC)
+ * and NFCv2 (as found in Armada 370/XP SoC).
+ */
+ enum pxa3xx_nand_variant variant;
+
+ int cs;
+ int use_ecc; /* use HW ECC ? */
+ int ecc_bch; /* using BCH ECC? */
+ int use_spare; /* use spare ? */
+ int need_wait;
+
+ /* Amount of real data per full chunk */
+ unsigned int chunk_size;
+
+ /* Amount of spare data per full chunk */
+ unsigned int spare_size;
+
+ /* Number of full chunks (i.e chunk_size + spare_size) */
+ unsigned int nfullchunks;
+
+ /*
+ * Total number of chunks. If equal to nfullchunks, then there
+ * are only full chunks. Otherwise, there is one last chunk of
+ * size (last_chunk_size + last_spare_size)
+ */
+ unsigned int ntotalchunks;
+
+ /* Amount of real data in the last chunk */
+ unsigned int last_chunk_size;
+
+ /* Amount of spare data in the last chunk */
+ unsigned int last_spare_size;
+
+ unsigned int ecc_size;
+ unsigned int ecc_err_cnt;
+ unsigned int max_bitflips;
+ int retcode;
+
+ /*
+ * Variables only valid during command
+ * execution. step_chunk_size and step_spare_size is the
+ * amount of real data and spare data in the current
+ * chunk. cur_chunk is the current chunk being
+ * read/programmed.
+ */
+ unsigned int step_chunk_size;
+ unsigned int step_spare_size;
+ unsigned int cur_chunk;
+
+ /* cached register value */
+ uint32_t reg_ndcr;
+ uint32_t ndtr0cs0;
+ uint32_t ndtr1cs0;
+
+ /* generated NDCBx register values */
+ uint32_t ndcb0;
+ uint32_t ndcb1;
+ uint32_t ndcb2;
+ uint32_t ndcb3;
+};
+
+static struct pxa3xx_nand_timing timing[] = {
+ /*
+ * tCH Enable signal hold time
+ * tCS Enable signal setup time
+ * tWH ND_nWE high duration
+ * tWP ND_nWE pulse time
+ * tRH ND_nRE high duration
+ * tRP ND_nRE pulse width
+ * tR ND_nWE high to ND_nRE low for read
+ * tWHR ND_nWE high to ND_nRE low for status read
+ * tAR ND_ALE low to ND_nRE low delay
+ */
+ /*ch cs wh wp rh rp r whr ar */
+ { 40, 80, 60, 100, 80, 100, 90000, 400, 40, },
+ { 10, 0, 20, 40, 30, 40, 11123, 110, 10, },
+ { 10, 25, 15, 25, 15, 30, 25000, 60, 10, },
+ { 10, 35, 15, 25, 15, 25, 25000, 60, 10, },
+ { 5, 20, 10, 12, 10, 12, 25000, 60, 10, },
+};
+
+static struct pxa3xx_nand_flash builtin_flash_types[] = {
+ /*
+ * chip_id
+ * flash_width Width of Flash memory (DWIDTH_M)
+ * dfc_width Width of flash controller(DWIDTH_C)
+ * *timing
+ * http://www.linux-mtd.infradead.org/nand-data/nanddata.html
+ */
+ { 0x46ec, 16, 16, &timing[1] },
+ { 0xdaec, 8, 8, &timing[1] },
+ { 0xd7ec, 8, 8, &timing[1] },
+ { 0xa12c, 8, 8, &timing[2] },
+ { 0xb12c, 16, 16, &timing[2] },
+ { 0xdc2c, 8, 8, &timing[2] },
+ { 0xcc2c, 16, 16, &timing[2] },
+ { 0xba20, 16, 16, &timing[3] },
+ { 0xda98, 8, 8, &timing[4] },
+};
+
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' };
+static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 8,
+ .len = 6,
+ .veroffs = 14,
+ .maxblocks = 8, /* Last 8 blocks in each chip */
+ .pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 8,
+ .len = 6,
+ .veroffs = 14,
+ .maxblocks = 8, /* Last 8 blocks in each chip */
+ .pattern = bbt_mirror_pattern
+};
+#endif
+
+static struct nand_ecclayout ecc_layout_2KB_bch4bit = {
+ .eccbytes = 32,
+ .eccpos = {
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63},
+ .oobfree = { {2, 30} }
+};
+
+static struct nand_ecclayout ecc_layout_2KB_bch8bit = {
+ .eccbytes = 64,
+ .eccpos = {
+ 64, 65, 66, 67, 68, 69, 70, 71,
+ 72, 73, 74, 75, 76, 77, 78, 79,
+ 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95,
+ 96, 97, 98, 99, 100, 101, 102, 103,
+ 104, 105, 106, 107, 108, 109, 110, 111,
+ 112, 113, 114, 115, 116, 117, 118, 119,
+ 120, 121, 122, 123, 124, 125, 126, 127},
+ .oobfree = { {1, 4}, {6, 26} }
+};
+
+static struct nand_ecclayout ecc_layout_4KB_bch4bit = {
+ .eccbytes = 64,
+ .eccpos = {
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63,
+ 96, 97, 98, 99, 100, 101, 102, 103,
+ 104, 105, 106, 107, 108, 109, 110, 111,
+ 112, 113, 114, 115, 116, 117, 118, 119,
+ 120, 121, 122, 123, 124, 125, 126, 127},
+ /* Bootrom looks in bytes 0 & 5 for bad blocks */
+ .oobfree = { {6, 26}, { 64, 32} }
+};
+
+static struct nand_ecclayout ecc_layout_8KB_bch4bit = {
+ .eccbytes = 128,
+ .eccpos = {
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63,
+
+ 96, 97, 98, 99, 100, 101, 102, 103,
+ 104, 105, 106, 107, 108, 109, 110, 111,
+ 112, 113, 114, 115, 116, 117, 118, 119,
+ 120, 121, 122, 123, 124, 125, 126, 127,
+
+ 160, 161, 162, 163, 164, 165, 166, 167,
+ 168, 169, 170, 171, 172, 173, 174, 175,
+ 176, 177, 178, 179, 180, 181, 182, 183,
+ 184, 185, 186, 187, 188, 189, 190, 191,
+
+ 224, 225, 226, 227, 228, 229, 230, 231,
+ 232, 233, 234, 235, 236, 237, 238, 239,
+ 240, 241, 242, 243, 244, 245, 246, 247,
+ 248, 249, 250, 251, 252, 253, 254, 255},
+
+ /* Bootrom looks in bytes 0 & 5 for bad blocks */
+ .oobfree = { {1, 4}, {6, 26}, { 64, 32}, {128, 32}, {192, 32} }
+};
+
+static struct nand_ecclayout ecc_layout_4KB_bch8bit = {
+ .eccbytes = 128,
+ .eccpos = {
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63},
+ .oobfree = { }
+};
+
+static struct nand_ecclayout ecc_layout_8KB_bch8bit = {
+ .eccbytes = 256,
+ .eccpos = {},
+ /* HW ECC handles all ECC data and all spare area is free for OOB */
+ .oobfree = {{0, 160} }
+};
+
+#define NDTR0_tCH(c) (min((c), 7) << 19)
+#define NDTR0_tCS(c) (min((c), 7) << 16)
+#define NDTR0_tWH(c) (min((c), 7) << 11)
+#define NDTR0_tWP(c) (min((c), 7) << 8)
+#define NDTR0_tRH(c) (min((c), 7) << 3)
+#define NDTR0_tRP(c) (min((c), 7) << 0)
+
+#define NDTR1_tR(c) (min((c), 65535) << 16)
+#define NDTR1_tWHR(c) (min((c), 15) << 4)
+#define NDTR1_tAR(c) (min((c), 15) << 0)
+
+/* convert nano-seconds to nand flash controller clock cycles */
+#define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000)
+
+static enum pxa3xx_nand_variant pxa3xx_nand_get_variant(void)
+{
+ /* We only support the Armada 370/XP/38x for now */
+ return PXA3XX_NAND_VARIANT_ARMADA370;
+}
+
+static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
+ const struct pxa3xx_nand_timing *t)
+{
+ struct pxa3xx_nand_info *info = host->info_data;
+ unsigned long nand_clk = mvebu_get_nand_clock();
+ uint32_t ndtr0, ndtr1;
+
+ ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) |
+ NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) |
+ NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) |
+ NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) |
+ NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) |
+ NDTR0_tRP(ns2cycle(t->tRP, nand_clk));
+
+ ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) |
+ NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
+ NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
+
+ info->ndtr0cs0 = ndtr0;
+ info->ndtr1cs0 = ndtr1;
+ nand_writel(info, NDTR0CS0, ndtr0);
+ nand_writel(info, NDTR1CS0, ndtr1);
+}
+
+static void pxa3xx_nand_set_sdr_timing(struct pxa3xx_nand_host *host,
+ const struct nand_sdr_timings *t)
+{
+ struct pxa3xx_nand_info *info = host->info_data;
+ struct nand_chip *chip = &host->chip;
+ unsigned long nand_clk = mvebu_get_nand_clock();
+ uint32_t ndtr0, ndtr1;
+
+ u32 tCH_min = DIV_ROUND_UP(t->tCH_min, 1000);
+ u32 tCS_min = DIV_ROUND_UP(t->tCS_min, 1000);
+ u32 tWH_min = DIV_ROUND_UP(t->tWH_min, 1000);
+ u32 tWP_min = DIV_ROUND_UP(t->tWC_min - t->tWH_min, 1000);
+ u32 tREH_min = DIV_ROUND_UP(t->tREH_min, 1000);
+ u32 tRP_min = DIV_ROUND_UP(t->tRC_min - t->tREH_min, 1000);
+ u32 tR = chip->chip_delay * 1000;
+ u32 tWHR_min = DIV_ROUND_UP(t->tWHR_min, 1000);
+ u32 tAR_min = DIV_ROUND_UP(t->tAR_min, 1000);
+
+ /* fallback to a default value if tR = 0 */
+ if (!tR)
+ tR = 20000;
+
+ ndtr0 = NDTR0_tCH(ns2cycle(tCH_min, nand_clk)) |
+ NDTR0_tCS(ns2cycle(tCS_min, nand_clk)) |
+ NDTR0_tWH(ns2cycle(tWH_min, nand_clk)) |
+ NDTR0_tWP(ns2cycle(tWP_min, nand_clk)) |
+ NDTR0_tRH(ns2cycle(tREH_min, nand_clk)) |
+ NDTR0_tRP(ns2cycle(tRP_min, nand_clk));
+
+ ndtr1 = NDTR1_tR(ns2cycle(tR, nand_clk)) |
+ NDTR1_tWHR(ns2cycle(tWHR_min, nand_clk)) |
+ NDTR1_tAR(ns2cycle(tAR_min, nand_clk));
+
+ info->ndtr0cs0 = ndtr0;
+ info->ndtr1cs0 = ndtr1;
+ nand_writel(info, NDTR0CS0, ndtr0);
+ nand_writel(info, NDTR1CS0, ndtr1);
+}
+
+static int pxa3xx_nand_init_timings(struct pxa3xx_nand_host *host)
+{
+ const struct nand_sdr_timings *timings;
+ struct nand_chip *chip = &host->chip;
+ struct pxa3xx_nand_info *info = host->info_data;
+ const struct pxa3xx_nand_flash *f = NULL;
+ struct mtd_info *mtd = nand_to_mtd(&host->chip);
+ int mode, id, ntypes, i;
+
+ mode = onfi_get_async_timing_mode(chip);
+ if (mode == ONFI_TIMING_MODE_UNKNOWN) {
+ ntypes = ARRAY_SIZE(builtin_flash_types);
+
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+
+ id = chip->read_byte(mtd);
+ id |= chip->read_byte(mtd) << 0x8;
+
+ for (i = 0; i < ntypes; i++) {
+ f = &builtin_flash_types[i];
+
+ if (f->chip_id == id)
+ break;
+ }
+
+ if (i == ntypes) {
+ dev_err(&info->pdev->dev, "Error: timings not found\n");
+ return -EINVAL;
+ }
+
+ pxa3xx_nand_set_timing(host, f->timing);
+
+ if (f->flash_width == 16) {
+ info->reg_ndcr |= NDCR_DWIDTH_M;
+ chip->options |= NAND_BUSWIDTH_16;
+ }
+
+ info->reg_ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
+ } else {
+ mode = fls(mode) - 1;
+ if (mode < 0)
+ mode = 0;
+
+ timings = onfi_async_timing_mode_to_sdr_timings(mode);
+ if (IS_ERR(timings))
+ return PTR_ERR(timings);
+
+ pxa3xx_nand_set_sdr_timing(host, timings);
+ }
+
+ return 0;
+}
+
+/**
+ * NOTE: it is a must to set ND_RUN first, then write
+ * command buffer, otherwise, it does not work.
+ * We enable all the interrupt at the same time, and
+ * let pxa3xx_nand_irq to handle all logic.
+ */
+static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+
+ ndcr = info->reg_ndcr;
+
+ if (info->use_ecc) {
+ ndcr |= NDCR_ECC_EN;
+ if (info->ecc_bch)
+ nand_writel(info, NDECCCTRL, 0x1);
+ } else {
+ ndcr &= ~NDCR_ECC_EN;
+ if (info->ecc_bch)
+ nand_writel(info, NDECCCTRL, 0x0);
+ }
+
+ ndcr &= ~NDCR_DMA_EN;
+
+ if (info->use_spare)
+ ndcr |= NDCR_SPARE_EN;
+ else
+ ndcr &= ~NDCR_SPARE_EN;
+
+ ndcr |= NDCR_ND_RUN;
+
+ /* clear status bits and run */
+ nand_writel(info, NDSR, NDSR_MASK);
+ nand_writel(info, NDCR, 0);
+ nand_writel(info, NDCR, ndcr);
+}
+
+static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
+{
+ uint32_t ndcr;
+
+ ndcr = nand_readl(info, NDCR);
+ nand_writel(info, NDCR, ndcr | int_mask);
+}
+
+static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
+{
+ if (info->ecc_bch) {
+ u32 ts;
+
+ /*
+ * According to the datasheet, when reading from NDDB
+ * with BCH enabled, after each 32 bytes reads, we
+ * have to make sure that the NDSR.RDDREQ bit is set.
+ *
+ * Drain the FIFO 8 32 bits reads at a time, and skip
+ * the polling on the last read.
+ */
+ while (len > 8) {
+ readsl(info->mmio_base + NDDB, data, 8);
+
+ ts = get_timer(0);
+ while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) {
+ if (get_timer(ts) > TIMEOUT_DRAIN_FIFO) {
+ dev_err(&info->pdev->dev,
+ "Timeout on RDDREQ while draining the FIFO\n");
+ return;
+ }
+ }
+
+ data += 32;
+ len -= 8;
+ }
+ }
+
+ readsl(info->mmio_base + NDDB, data, len);
+}
+
+static void handle_data_pio(struct pxa3xx_nand_info *info)
+{
+ switch (info->state) {
+ case STATE_PIO_WRITING:
+ if (info->step_chunk_size)
+ writesl(info->mmio_base + NDDB,
+ info->data_buff + info->data_buff_pos,
+ DIV_ROUND_UP(info->step_chunk_size, 4));
+
+ if (info->step_spare_size)
+ writesl(info->mmio_base + NDDB,
+ info->oob_buff + info->oob_buff_pos,
+ DIV_ROUND_UP(info->step_spare_size, 4));
+ break;
+ case STATE_PIO_READING:
+ if (info->step_chunk_size)
+ drain_fifo(info,
+ info->data_buff + info->data_buff_pos,
+ DIV_ROUND_UP(info->step_chunk_size, 4));
+
+ if (info->step_spare_size)
+ drain_fifo(info,
+ info->oob_buff + info->oob_buff_pos,
+ DIV_ROUND_UP(info->step_spare_size, 4));
+ break;
+ default:
+ dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
+ info->state);
+ BUG();
+ }
+
+ /* Update buffer pointers for multi-page read/write */
+ info->data_buff_pos += info->step_chunk_size;
+ info->oob_buff_pos += info->step_spare_size;
+}
+
+static void pxa3xx_nand_irq_thread(struct pxa3xx_nand_info *info)
+{
+ handle_data_pio(info);
+
+ info->state = STATE_CMD_DONE;
+ nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
+}
+
+static irqreturn_t pxa3xx_nand_irq(struct pxa3xx_nand_info *info)
+{
+ unsigned int status, is_completed = 0, is_ready = 0;
+ unsigned int ready, cmd_done;
+ irqreturn_t ret = IRQ_HANDLED;
+
+ if (info->cs == 0) {
+ ready = NDSR_FLASH_RDY;
+ cmd_done = NDSR_CS0_CMDD;
+ } else {
+ ready = NDSR_RDY;
+ cmd_done = NDSR_CS1_CMDD;
+ }
+
+ /* TODO - find out why we need the delay during write operation. */
+ ndelay(1);
+
+ status = nand_readl(info, NDSR);
+
+ if (status & NDSR_UNCORERR)
+ info->retcode = ERR_UNCORERR;
+ if (status & NDSR_CORERR) {
+ info->retcode = ERR_CORERR;
+ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 &&
+ info->ecc_bch)
+ info->ecc_err_cnt = NDSR_ERR_CNT(status);
+ else
+ info->ecc_err_cnt = 1;
+
+ /*
+ * Each chunk composing a page is corrected independently,
+ * and we need to store maximum number of corrected bitflips
+ * to return it to the MTD layer in ecc.read_page().
+ */
+ info->max_bitflips = max_t(unsigned int,
+ info->max_bitflips,
+ info->ecc_err_cnt);
+ }
+ if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
+ info->state = (status & NDSR_RDDREQ) ?
+ STATE_PIO_READING : STATE_PIO_WRITING;
+ /* Call the IRQ thread in U-Boot directly */
+ pxa3xx_nand_irq_thread(info);
+ return 0;
+ }
+ if (status & cmd_done) {
+ info->state = STATE_CMD_DONE;
+ is_completed = 1;
+ }
+ if (status & ready) {
+ info->state = STATE_READY;
+ is_ready = 1;
+ }
+
+ /*
+ * Clear all status bit before issuing the next command, which
+ * can and will alter the status bits and will deserve a new
+ * interrupt on its own. This lets the controller exit the IRQ
+ */
+ nand_writel(info, NDSR, status);
+
+ if (status & NDSR_WRCMDREQ) {
+ status &= ~NDSR_WRCMDREQ;
+ info->state = STATE_CMD_HANDLE;
+
+ /*
+ * Command buffer registers NDCB{0-2} (and optionally NDCB3)
+ * must be loaded by writing directly either 12 or 16
+ * bytes directly to NDCB0, four bytes at a time.
+ *
+ * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored
+ * but each NDCBx register can be read.
+ */
+ nand_writel(info, NDCB0, info->ndcb0);
+ nand_writel(info, NDCB0, info->ndcb1);
+ nand_writel(info, NDCB0, info->ndcb2);
+
+ /* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */
+ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+ nand_writel(info, NDCB0, info->ndcb3);
+ }
+
+ if (is_completed)
+ info->cmd_complete = 1;
+ if (is_ready)
+ info->dev_ready = 1;
+
+ return ret;
+}
+
+static inline int is_buf_blank(uint8_t *buf, size_t len)
+{
+ for (; len > 0; len--)
+ if (*buf++ != 0xff)
+ return 0;
+ return 1;
+}
+
+static void set_command_address(struct pxa3xx_nand_info *info,
+ unsigned int page_size, uint16_t column, int page_addr)
+{
+ /* small page addr setting */
+ if (page_size < info->chunk_size) {
+ info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
+ | (column & 0xFF);
+
+ info->ndcb2 = 0;
+ } else {
+ info->ndcb1 = ((page_addr & 0xFFFF) << 16)
+ | (column & 0xFFFF);
+
+ if (page_addr & 0xFF0000)
+ info->ndcb2 = (page_addr & 0xFF0000) >> 16;
+ else
+ info->ndcb2 = 0;
+ }
+}
+
+static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
+{
+ struct pxa3xx_nand_host *host = info->host[info->cs];
+ struct mtd_info *mtd = nand_to_mtd(&host->chip);
+
+ /* reset data and oob column point to handle data */
+ info->buf_start = 0;
+ info->buf_count = 0;
+ info->data_buff_pos = 0;
+ info->oob_buff_pos = 0;
+ info->step_chunk_size = 0;
+ info->step_spare_size = 0;
+ info->cur_chunk = 0;
+ info->use_ecc = 0;
+ info->use_spare = 1;
+ info->retcode = ERR_NONE;
+ info->ecc_err_cnt = 0;
+ info->ndcb3 = 0;
+ info->need_wait = 0;
+
+ switch (command) {
+ case NAND_CMD_READ0:
+ case NAND_CMD_READOOB:
+ case NAND_CMD_PAGEPROG:
+ info->use_ecc = 1;
+ break;
+ case NAND_CMD_PARAM:
+ info->use_spare = 0;
+ break;
+ default:
+ info->ndcb1 = 0;
+ info->ndcb2 = 0;
+ break;
+ }
+
+ /*
+ * If we are about to issue a read command, or about to set
+ * the write address, then clean the data buffer.
+ */
+ if (command == NAND_CMD_READ0 ||
+ command == NAND_CMD_READOOB ||
+ command == NAND_CMD_SEQIN) {
+ info->buf_count = mtd->writesize + mtd->oobsize;
+ memset(info->data_buff, 0xFF, info->buf_count);
+ }
+}
+
+static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
+ int ext_cmd_type, uint16_t column, int page_addr)
+{
+ int addr_cycle, exec_cmd;
+ struct pxa3xx_nand_host *host;
+ struct mtd_info *mtd;
+
+ host = info->host[info->cs];
+ mtd = nand_to_mtd(&host->chip);
+ addr_cycle = 0;
+ exec_cmd = 1;
+
+ if (info->cs != 0)
+ info->ndcb0 = NDCB0_CSEL;
+ else
+ info->ndcb0 = 0;
+
+ if (command == NAND_CMD_SEQIN)
+ exec_cmd = 0;
+
+ addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
+ + host->col_addr_cycles);
+
+ switch (command) {
+ case NAND_CMD_READOOB:
+ case NAND_CMD_READ0:
+ info->buf_start = column;
+ info->ndcb0 |= NDCB0_CMD_TYPE(0)
+ | addr_cycle
+ | NAND_CMD_READ0;
+
+ if (command == NAND_CMD_READOOB)
+ info->buf_start += mtd->writesize;
+
+ if (info->cur_chunk < info->nfullchunks) {
+ info->step_chunk_size = info->chunk_size;
+ info->step_spare_size = info->spare_size;
+ } else {
+ info->step_chunk_size = info->last_chunk_size;
+ info->step_spare_size = info->last_spare_size;
+ }
+
+ /*
+ * Multiple page read needs an 'extended command type' field,
+ * which is either naked-read or last-read according to the
+ * state.
+ */
+ if (mtd->writesize == info->chunk_size) {
+ info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
+ } else if (mtd->writesize > info->chunk_size) {
+ info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8)
+ | NDCB0_LEN_OVRD
+ | NDCB0_EXT_CMD_TYPE(ext_cmd_type);
+ info->ndcb3 = info->step_chunk_size +
+ info->step_spare_size;
+ }
+
+ set_command_address(info, mtd->writesize, column, page_addr);
+ break;
+
+ case NAND_CMD_SEQIN:
+
+ info->buf_start = column;
+ set_command_address(info, mtd->writesize, 0, page_addr);
+
+ /*
+ * Multiple page programming needs to execute the initial
+ * SEQIN command that sets the page address.
+ */
+ if (mtd->writesize > info->chunk_size) {
+ info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+ | NDCB0_EXT_CMD_TYPE(ext_cmd_type)
+ | addr_cycle
+ | command;
+ exec_cmd = 1;
+ }
+ break;
+
+ case NAND_CMD_PAGEPROG:
+ if (is_buf_blank(info->data_buff,
+ (mtd->writesize + mtd->oobsize))) {
+ exec_cmd = 0;
+ break;
+ }
+
+ if (info->cur_chunk < info->nfullchunks) {
+ info->step_chunk_size = info->chunk_size;
+ info->step_spare_size = info->spare_size;
+ } else {
+ info->step_chunk_size = info->last_chunk_size;
+ info->step_spare_size = info->last_spare_size;
+ }
+
+ /* Second command setting for large pages */
+ if (mtd->writesize > info->chunk_size) {
+ /*
+ * Multiple page write uses the 'extended command'
+ * field. This can be used to issue a command dispatch
+ * or a naked-write depending on the current stage.
+ */
+ info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+ | NDCB0_LEN_OVRD
+ | NDCB0_EXT_CMD_TYPE(ext_cmd_type);
+ info->ndcb3 = info->step_chunk_size +
+ info->step_spare_size;
+
+ /*
+ * This is the command dispatch that completes a chunked
+ * page program operation.
+ */
+ if (info->cur_chunk == info->ntotalchunks) {
+ info->ndcb0 = NDCB0_CMD_TYPE(0x1)
+ | NDCB0_EXT_CMD_TYPE(ext_cmd_type)
+ | command;
+ info->ndcb1 = 0;
+ info->ndcb2 = 0;
+ info->ndcb3 = 0;
+ }
+ } else {
+ info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+ | NDCB0_AUTO_RS
+ | NDCB0_ST_ROW_EN
+ | NDCB0_DBC
+ | (NAND_CMD_PAGEPROG << 8)
+ | NAND_CMD_SEQIN
+ | addr_cycle;
+ }
+ break;
+
+ case NAND_CMD_PARAM:
+ info->buf_count = INIT_BUFFER_SIZE;
+ info->ndcb0 |= NDCB0_CMD_TYPE(0)
+ | NDCB0_ADDR_CYC(1)
+ | NDCB0_LEN_OVRD
+ | command;
+ info->ndcb1 = (column & 0xFF);
+ info->ndcb3 = INIT_BUFFER_SIZE;
+ info->step_chunk_size = INIT_BUFFER_SIZE;
+ break;
+
+ case NAND_CMD_READID:
+ info->buf_count = READ_ID_BYTES;
+ info->ndcb0 |= NDCB0_CMD_TYPE(3)
+ | NDCB0_ADDR_CYC(1)
+ | command;
+ info->ndcb1 = (column & 0xFF);
+
+ info->step_chunk_size = 8;
+ break;
+ case NAND_CMD_STATUS:
+ info->buf_count = 1;
+ info->ndcb0 |= NDCB0_CMD_TYPE(4)
+ | NDCB0_ADDR_CYC(1)
+ | command;
+
+ info->step_chunk_size = 8;
+ break;
+
+ case NAND_CMD_ERASE1:
+ info->ndcb0 |= NDCB0_CMD_TYPE(2)
+ | NDCB0_AUTO_RS
+ | NDCB0_ADDR_CYC(3)
+ | NDCB0_DBC
+ | (NAND_CMD_ERASE2 << 8)
+ | NAND_CMD_ERASE1;
+ info->ndcb1 = page_addr;
+ info->ndcb2 = 0;
+
+ break;
+ case NAND_CMD_RESET:
+ info->ndcb0 |= NDCB0_CMD_TYPE(5)
+ | command;
+
+ break;
+
+ case NAND_CMD_ERASE2:
+ exec_cmd = 0;
+ break;
+
+ default:
+ exec_cmd = 0;
+ dev_err(&info->pdev->dev, "non-supported command %x\n",
+ command);
+ break;
+ }
+
+ return exec_cmd;
+}
+
+static void nand_cmdfunc(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ int exec_cmd;
+
+ /*
+ * if this is a x16 device ,then convert the input
+ * "byte" address into a "word" address appropriate
+ * for indexing a word-oriented device
+ */
+ if (info->reg_ndcr & NDCR_DWIDTH_M)
+ column /= 2;
+
+ /*
+ * There may be different NAND chip hooked to
+ * different chip select, so check whether
+ * chip select has been changed, if yes, reset the timing
+ */
+ if (info->cs != host->cs) {
+ info->cs = host->cs;
+ nand_writel(info, NDTR0CS0, info->ndtr0cs0);
+ nand_writel(info, NDTR1CS0, info->ndtr1cs0);
+ }
+
+ prepare_start_command(info, command);
+
+ info->state = STATE_PREPARED;
+ exec_cmd = prepare_set_command(info, command, 0, column, page_addr);
+
+ if (exec_cmd) {
+ u32 ts;
+
+ info->cmd_complete = 0;
+ info->dev_ready = 0;
+ info->need_wait = 1;
+ pxa3xx_nand_start(info);
+
+ ts = get_timer(0);
+ while (1) {
+ u32 status;
+
+ status = nand_readl(info, NDSR);
+ if (status)
+ pxa3xx_nand_irq(info);
+
+ if (info->cmd_complete)
+ break;
+
+ if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
+ dev_err(&info->pdev->dev, "Wait timeout!!!\n");
+ return;
+ }
+ }
+ }
+ info->state = STATE_IDLE;
+}
+
+static void nand_cmdfunc_extended(struct mtd_info *mtd,
+ const unsigned command,
+ int column, int page_addr)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ int exec_cmd, ext_cmd_type;
+
+ /*
+ * if this is a x16 device then convert the input
+ * "byte" address into a "word" address appropriate
+ * for indexing a word-oriented device
+ */
+ if (info->reg_ndcr & NDCR_DWIDTH_M)
+ column /= 2;
+
+ /*
+ * There may be different NAND chip hooked to
+ * different chip select, so check whether
+ * chip select has been changed, if yes, reset the timing
+ */
+ if (info->cs != host->cs) {
+ info->cs = host->cs;
+ nand_writel(info, NDTR0CS0, info->ndtr0cs0);
+ nand_writel(info, NDTR1CS0, info->ndtr1cs0);
+ }
+
+ /* Select the extended command for the first command */
+ switch (command) {
+ case NAND_CMD_READ0:
+ case NAND_CMD_READOOB:
+ ext_cmd_type = EXT_CMD_TYPE_MONO;
+ break;
+ case NAND_CMD_SEQIN:
+ ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
+ break;
+ case NAND_CMD_PAGEPROG:
+ ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
+ break;
+ default:
+ ext_cmd_type = 0;
+ break;
+ }
+
+ prepare_start_command(info, command);
+
+ /*
+ * Prepare the "is ready" completion before starting a command
+ * transaction sequence. If the command is not executed the
+ * completion will be completed, see below.
+ *
+ * We can do that inside the loop because the command variable
+ * is invariant and thus so is the exec_cmd.
+ */
+ info->need_wait = 1;
+ info->dev_ready = 0;
+
+ do {
+ u32 ts;
+
+ info->state = STATE_PREPARED;
+ exec_cmd = prepare_set_command(info, command, ext_cmd_type,
+ column, page_addr);
+ if (!exec_cmd) {
+ info->need_wait = 0;
+ info->dev_ready = 1;
+ break;
+ }
+
+ info->cmd_complete = 0;
+ pxa3xx_nand_start(info);
+
+ ts = get_timer(0);
+ while (1) {
+ u32 status;
+
+ status = nand_readl(info, NDSR);
+ if (status)
+ pxa3xx_nand_irq(info);
+
+ if (info->cmd_complete)
+ break;
+
+ if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
+ dev_err(&info->pdev->dev, "Wait timeout!!!\n");
+ return;
+ }
+ }
+
+ /* Only a few commands need several steps */
+ if (command != NAND_CMD_PAGEPROG &&
+ command != NAND_CMD_READ0 &&
+ command != NAND_CMD_READOOB)
+ break;
+
+ info->cur_chunk++;
+
+ /* Check if the sequence is complete */
+ if (info->cur_chunk == info->ntotalchunks &&
+ command != NAND_CMD_PAGEPROG)
+ break;
+
+ /*
+ * After a splitted program command sequence has issued
+ * the command dispatch, the command sequence is complete.
+ */
+ if (info->cur_chunk == (info->ntotalchunks + 1) &&
+ command == NAND_CMD_PAGEPROG &&
+ ext_cmd_type == EXT_CMD_TYPE_DISPATCH)
+ break;
+
+ if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) {
+ /* Last read: issue a 'last naked read' */
+ if (info->cur_chunk == info->ntotalchunks - 1)
+ ext_cmd_type = EXT_CMD_TYPE_LAST_RW;
+ else
+ ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
+
+ /*
+ * If a splitted program command has no more data to transfer,
+ * the command dispatch must be issued to complete.
+ */
+ } else if (command == NAND_CMD_PAGEPROG &&
+ info->cur_chunk == info->ntotalchunks) {
+ ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
+ }
+ } while (1);
+
+ info->state = STATE_IDLE;
+}
+
+static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf, int oob_required,
+ int page)
+{
+ chip->write_buf(mtd, buf, mtd->writesize);
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required,
+ int page)
+{
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+
+ chip->read_buf(mtd, buf, mtd->writesize);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ if (info->retcode == ERR_CORERR && info->use_ecc) {
+ mtd->ecc_stats.corrected += info->ecc_err_cnt;
+
+ } else if (info->retcode == ERR_UNCORERR) {
+ /*
+ * for blank page (all 0xff), HW will calculate its ECC as
+ * 0, which is different from the ECC information within
+ * OOB, ignore such uncorrectable errors
+ */
+ if (is_buf_blank(buf, mtd->writesize))
+ info->retcode = ERR_NONE;
+ else
+ mtd->ecc_stats.failed++;
+ }
+
+ return info->max_bitflips;
+}
+
+static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ char retval = 0xFF;
+
+ if (info->buf_start < info->buf_count)
+ /* Has just send a new command? */
+ retval = info->data_buff[info->buf_start++];
+
+ return retval;
+}
+
+static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ u16 retval = 0xFFFF;
+
+ if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
+ retval = *((u16 *)(info->data_buff+info->buf_start));
+ info->buf_start += 2;
+ }
+ return retval;
+}
+
+static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
+
+ memcpy(buf, info->data_buff + info->buf_start, real_len);
+ info->buf_start += real_len;
+}
+
+static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
+ const uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
+
+ memcpy(info->data_buff + info->buf_start, buf, real_len);
+ info->buf_start += real_len;
+}
+
+static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
+{
+ return;
+}
+
+static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+
+ if (info->need_wait) {
+ u32 ts;
+
+ info->need_wait = 0;
+
+ ts = get_timer(0);
+ while (1) {
+ u32 status;
+
+ status = nand_readl(info, NDSR);
+ if (status)
+ pxa3xx_nand_irq(info);
+
+ if (info->dev_ready)
+ break;
+
+ if (get_timer(ts) > CHIP_DELAY_TIMEOUT) {
+ dev_err(&info->pdev->dev, "Ready timeout!!!\n");
+ return NAND_STATUS_FAIL;
+ }
+ }
+ }
+
+ /* pxa3xx_nand_send_command has waited for command complete */
+ if (this->state == FL_WRITING || this->state == FL_ERASING) {
+ if (info->retcode == ERR_NONE)
+ return 0;
+ else
+ return NAND_STATUS_FAIL;
+ }
+
+ return NAND_STATUS_READY;
+}
+
+static int pxa3xx_nand_config_ident(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_platform_data *pdata = info->pdata;
+
+ /* Configure default flash values */
+ info->reg_ndcr = 0x0; /* enable all interrupts */
+ info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
+ info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
+ info->reg_ndcr |= NDCR_SPARE_EN;
+
+ return 0;
+}
+
+static void pxa3xx_nand_config_tail(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_host *host = info->host[info->cs];
+ struct mtd_info *mtd = nand_to_mtd(&info->host[info->cs]->chip);
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ info->reg_ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
+ info->reg_ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0;
+ info->reg_ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
+}
+
+static void pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_platform_data *pdata = info->pdata;
+ uint32_t ndcr = nand_readl(info, NDCR);
+
+ /* Set an initial chunk size */
+ info->chunk_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512;
+ info->reg_ndcr = ndcr &
+ ~(NDCR_INT_MASK | NDCR_ND_ARB_EN | NFCV1_NDCR_ARB_CNTL);
+ info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
+ info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
+ info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
+}
+
+static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
+{
+ info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
+ if (info->data_buff == NULL)
+ return -ENOMEM;
+ return 0;
+}
+
+static int pxa3xx_nand_sensing(struct pxa3xx_nand_host *host)
+{
+ struct pxa3xx_nand_info *info = host->info_data;
+ struct pxa3xx_nand_platform_data *pdata = info->pdata;
+ struct mtd_info *mtd;
+ struct nand_chip *chip;
+ const struct nand_sdr_timings *timings;
+ int ret;
+
+ mtd = nand_to_mtd(&info->host[info->cs]->chip);
+ chip = mtd_to_nand(mtd);
+
+ /* configure default flash values */
+ info->reg_ndcr = 0x0; /* enable all interrupts */
+ info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
+ info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
+ info->reg_ndcr |= NDCR_SPARE_EN; /* enable spare by default */
+
+ /* use the common timing to make a try */
+ timings = onfi_async_timing_mode_to_sdr_timings(0);
+ if (IS_ERR(timings))
+ return PTR_ERR(timings);
+
+ pxa3xx_nand_set_sdr_timing(host, timings);
+
+ chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
+ ret = chip->waitfunc(mtd, chip);
+ if (ret & NAND_STATUS_FAIL)
+ return -ENODEV;
+
+ return 0;
+}
+
+static int pxa_ecc_init(struct pxa3xx_nand_info *info,
+ struct nand_ecc_ctrl *ecc,
+ int strength, int ecc_stepsize, int page_size)
+{
+ if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) {
+ info->nfullchunks = 1;
+ info->ntotalchunks = 1;
+ info->chunk_size = 2048;
+ info->spare_size = 40;
+ info->ecc_size = 24;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = 512;
+ ecc->strength = 1;
+
+ } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) {
+ info->nfullchunks = 1;
+ info->ntotalchunks = 1;
+ info->chunk_size = 512;
+ info->spare_size = 8;
+ info->ecc_size = 8;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = 512;
+ ecc->strength = 1;
+
+ /*
+ * Required ECC: 4-bit correction per 512 bytes
+ * Select: 16-bit correction per 2048 bytes
+ */
+ } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 1;
+ info->ntotalchunks = 1;
+ info->chunk_size = 2048;
+ info->spare_size = 32;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_2KB_bch4bit;
+ ecc->strength = 16;
+
+ } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 2;
+ info->ntotalchunks = 2;
+ info->chunk_size = 2048;
+ info->spare_size = 32;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_4KB_bch4bit;
+ ecc->strength = 16;
+
+ } else if (strength == 4 && ecc_stepsize == 512 && page_size == 8192) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 4;
+ info->ntotalchunks = 4;
+ info->chunk_size = 2048;
+ info->spare_size = 32;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_8KB_bch4bit;
+ ecc->strength = 16;
+
+ /*
+ * Required ECC: 8-bit correction per 512 bytes
+ * Select: 16-bit correction per 1024 bytes
+ */
+ } else if (strength == 8 && ecc_stepsize == 512 && page_size == 2048) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 1;
+ info->ntotalchunks = 2;
+ info->chunk_size = 1024;
+ info->spare_size = 0;
+ info->last_chunk_size = 1024;
+ info->last_spare_size = 64;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_2KB_bch8bit;
+ ecc->strength = 16;
+
+ } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 4;
+ info->ntotalchunks = 5;
+ info->chunk_size = 1024;
+ info->spare_size = 0;
+ info->last_chunk_size = 0;
+ info->last_spare_size = 64;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_4KB_bch8bit;
+ ecc->strength = 16;
+
+ } else if (strength == 8 && ecc_stepsize == 512 && page_size == 8192) {
+ info->ecc_bch = 1;
+ info->nfullchunks = 8;
+ info->ntotalchunks = 9;
+ info->chunk_size = 1024;
+ info->spare_size = 0;
+ info->last_chunk_size = 0;
+ info->last_spare_size = 160;
+ info->ecc_size = 32;
+ ecc->mode = NAND_ECC_HW;
+ ecc->size = info->chunk_size;
+ ecc->layout = &ecc_layout_8KB_bch8bit;
+ ecc->strength = 16;
+
+ } else {
+ dev_err(&info->pdev->dev,
+ "ECC strength %d at page size %d is not supported\n",
+ strength, page_size);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int pxa3xx_nand_scan(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
+ struct pxa3xx_nand_info *info = host->info_data;
+ struct pxa3xx_nand_platform_data *pdata = info->pdata;
+ int ret;
+ uint16_t ecc_strength, ecc_step;
+
+ if (pdata->keep_config) {
+ pxa3xx_nand_detect_config(info);
+ } else {
+ ret = pxa3xx_nand_config_ident(info);
+ if (ret)
+ return ret;
+ ret = pxa3xx_nand_sensing(host);
+ if (ret) {
+ dev_info(&info->pdev->dev,
+ "There is no chip on cs %d!\n",
+ info->cs);
+ return ret;
+ }
+ }
+
+ /* Device detection must be done with ECC disabled */
+ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+ nand_writel(info, NDECCCTRL, 0x0);
+
+ if (nand_scan_ident(mtd, 1, NULL))
+ return -ENODEV;
+
+ if (!pdata->keep_config) {
+ ret = pxa3xx_nand_init_timings(host);
+ if (ret) {
+ dev_err(&info->pdev->dev,
+ "Failed to set timings: %d\n", ret);
+ return ret;
+ }
+ }
+
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ /*
+ * We'll use a bad block table stored in-flash and don't
+ * allow writing the bad block marker to the flash.
+ */
+ chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB_BBM;
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+#endif
+
+ if (pdata->ecc_strength && pdata->ecc_step_size) {
+ ecc_strength = pdata->ecc_strength;
+ ecc_step = pdata->ecc_step_size;
+ } else {
+ ecc_strength = chip->ecc_strength_ds;
+ ecc_step = chip->ecc_step_ds;
+ }
+
+ /* Set default ECC strength requirements on non-ONFI devices */
+ if (ecc_strength < 1 && ecc_step < 1) {
+ ecc_strength = 1;
+ ecc_step = 512;
+ }
+
+ ret = pxa_ecc_init(info, &chip->ecc, ecc_strength,
+ ecc_step, mtd->writesize);
+ if (ret)
+ return ret;
+
+ /*
+ * If the page size is bigger than the FIFO size, let's check
+ * we are given the right variant and then switch to the extended
+ * (aka split) command handling,
+ */
+ if (mtd->writesize > info->chunk_size) {
+ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) {
+ chip->cmdfunc = nand_cmdfunc_extended;
+ } else {
+ dev_err(&info->pdev->dev,
+ "unsupported page size on this variant\n");
+ return -ENODEV;
+ }
+ }
+
+ /* calculate addressing information */
+ if (mtd->writesize >= 2048)
+ host->col_addr_cycles = 2;
+ else
+ host->col_addr_cycles = 1;
+
+ /* release the initial buffer */
+ kfree(info->data_buff);
+
+ /* allocate the real data + oob buffer */
+ info->buf_size = mtd->writesize + mtd->oobsize;
+ ret = pxa3xx_nand_init_buff(info);
+ if (ret)
+ return ret;
+ info->oob_buff = info->data_buff + mtd->writesize;
+
+ if ((mtd->size >> chip->page_shift) > 65536)
+ host->row_addr_cycles = 3;
+ else
+ host->row_addr_cycles = 2;
+
+ if (!pdata->keep_config)
+ pxa3xx_nand_config_tail(info);
+
+ return nand_scan_tail(mtd);
+}
+
+static int alloc_nand_resource(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_platform_data *pdata;
+ struct pxa3xx_nand_host *host;
+ struct nand_chip *chip = NULL;
+ struct mtd_info *mtd;
+ int ret, cs;
+
+ pdata = info->pdata;
+ if (pdata->num_cs <= 0)
+ return -ENODEV;
+
+ info->variant = pxa3xx_nand_get_variant();
+ for (cs = 0; cs < pdata->num_cs; cs++) {
+ chip = (struct nand_chip *)
+ ((u8 *)&info[1] + sizeof(*host) * cs);
+ mtd = nand_to_mtd(chip);
+ host = (struct pxa3xx_nand_host *)chip;
+ info->host[cs] = host;
+ host->cs = cs;
+ host->info_data = info;
+ mtd->owner = THIS_MODULE;
+
+ nand_set_controller_data(chip, host);
+ chip->ecc.read_page = pxa3xx_nand_read_page_hwecc;
+ chip->ecc.write_page = pxa3xx_nand_write_page_hwecc;
+ chip->controller = &info->controller;
+ chip->waitfunc = pxa3xx_nand_waitfunc;
+ chip->select_chip = pxa3xx_nand_select_chip;
+ chip->read_word = pxa3xx_nand_read_word;
+ chip->read_byte = pxa3xx_nand_read_byte;
+ chip->read_buf = pxa3xx_nand_read_buf;
+ chip->write_buf = pxa3xx_nand_write_buf;
+ chip->options |= NAND_NO_SUBPAGE_WRITE;
+ chip->cmdfunc = nand_cmdfunc;
+ }
+
+ /* Allocate a buffer to allow flash detection */
+ info->buf_size = INIT_BUFFER_SIZE;
+ info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
+ if (info->data_buff == NULL) {
+ ret = -ENOMEM;
+ goto fail_disable_clk;
+ }
+
+ /* initialize all interrupts to be disabled */
+ disable_int(info, NDSR_MASK);
+
+ return 0;
+
+ kfree(info->data_buff);
+fail_disable_clk:
+ return ret;
+}
+
+static int pxa3xx_nand_probe_dt(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_platform_data *pdata;
+ const void *blob = gd->fdt_blob;
+ int node = -1;
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ /* Get address decoding nodes from the FDT blob */
+ do {
+ node = fdt_node_offset_by_compatible(blob, node,
+ "marvell,mvebu-pxa3xx-nand");
+ if (node < 0)
+ break;
+
+ /* Bypass disabeld nodes */
+ if (!fdtdec_get_is_enabled(blob, node))
+ continue;
+
+ /* Get the first enabled NAND controler base address */
+ info->mmio_base =
+ (void __iomem *)fdtdec_get_addr_size_auto_noparent(
+ blob, node, "reg", 0, NULL, true);
+
+ pdata->num_cs = fdtdec_get_int(blob, node, "num-cs", 1);
+ if (pdata->num_cs != 1) {
+ pr_err("pxa3xx driver supports single CS only\n");
+ break;
+ }
+
+ if (fdtdec_get_bool(blob, node, "nand-enable-arbiter"))
+ pdata->enable_arbiter = 1;
+
+ if (fdtdec_get_bool(blob, node, "nand-keep-config"))
+ pdata->keep_config = 1;
+
+ /*
+ * ECC parameters.
+ * If these are not set, they will be selected according
+ * to the detected flash type.
+ */
+ /* ECC strength */
+ pdata->ecc_strength = fdtdec_get_int(blob, node,
+ "nand-ecc-strength", 0);
+
+ /* ECC step size */
+ pdata->ecc_step_size = fdtdec_get_int(blob, node,
+ "nand-ecc-step-size", 0);
+
+ info->pdata = pdata;
+
+ /* Currently support only a single NAND controller */
+ return 0;
+
+ } while (node >= 0);
+
+ return -EINVAL;
+}
+
+static int pxa3xx_nand_probe(struct pxa3xx_nand_info *info)
+{
+ struct pxa3xx_nand_platform_data *pdata;
+ int ret, cs, probe_success;
+
+ ret = pxa3xx_nand_probe_dt(info);
+ if (ret)
+ return ret;
+
+ pdata = info->pdata;
+
+ ret = alloc_nand_resource(info);
+ if (ret) {
+ dev_err(&pdev->dev, "alloc nand resource failed\n");
+ return ret;
+ }
+
+ probe_success = 0;
+ for (cs = 0; cs < pdata->num_cs; cs++) {
+ struct mtd_info *mtd = nand_to_mtd(&info->host[cs]->chip);
+
+ /*
+ * The mtd name matches the one used in 'mtdparts' kernel
+ * parameter. This name cannot be changed or otherwise
+ * user's mtd partitions configuration would get broken.
+ */
+ mtd->name = "pxa3xx_nand-0";
+ info->cs = cs;
+ ret = pxa3xx_nand_scan(mtd);
+ if (ret) {
+ dev_info(&pdev->dev, "failed to scan nand at cs %d\n",
+ cs);
+ continue;
+ }
+
+ if (nand_register(cs, mtd))
+ continue;
+
+ probe_success = 1;
+ }
+
+ if (!probe_success)
+ return -ENODEV;
+
+ return 0;
+}
+
+/*
+ * Main initialization routine
+ */
+void board_nand_init(void)
+{
+ struct pxa3xx_nand_info *info;
+ struct pxa3xx_nand_host *host;
+ int ret;
+
+ info = kzalloc(sizeof(*info) +
+ sizeof(*host) * CONFIG_SYS_MAX_NAND_DEVICE,
+ GFP_KERNEL);
+ if (!info)
+ return;
+
+ ret = pxa3xx_nand_probe(info);
+ if (ret)
+ return;
+}