armv8: ls1088aqds: Add support of LS1088AQDS
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
new file mode 100644
index 0000000..3547b0b
--- /dev/null
+++ b/include/configs/ls1088aqds.h
@@ -0,0 +1,414 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1088A_QDS_H
+#define __LS1088A_QDS_H
+
+#include "ls1088a_common.h"
+
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x20000
+#endif
+
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define SYS_NO_FLASH
+
+#undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+#else
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+#endif
+
+#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS 0x51
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
+
+#define CONFIG_SYS_NOR0_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EARLY \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1a) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x04000000
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#ifndef SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
+ CONFIG_SYS_FLASH_BASE + 0x40000000}
+#endif
+#endif
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_MAX_ECCPOS 256
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_QMAP_MASK 0xe0
+#define QIXIS_QMAP_SHIFT 5
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x0e
+#define QIXIS_LBMAP_ALTBANK 0x2e
+#define QIXIS_LBMAP_SD 0x00
+#define QIXIS_LBMAP_SD_QSPI 0x0e
+#define QIXIS_LBMAP_QSPI 0x0e
+#define QIXIS_RCW_SRC_SD 0x40
+#define QIXIS_RCW_SRC_QSPI 0x62
+#define QIXIS_RST_CTL_RESET 0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_RST_FORCE_MEM 0x01
+#define QIXIS_STAT_PRES1 0xb
+#define QIXIS_SDID_MASK 0x07
+#define QIXIS_ESDHC_NO_ADAPTER 0x7
+
+#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
+#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+
+#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64*1024)
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0)
+#else
+#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(12)
+#endif
+/* QIXIS Timing parameters*/
+#define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
+ FTIM2_GPCM_TCH(0xf) | \
+ FTIM2_GPCM_TWP(0x3E))
+#define SYS_FPGA_CS_FTIM3 0x0
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
+#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
+#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR3_FINAL CONFIG_SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_CS_FTIM3
+#endif
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI 0x77
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR 0x18
+#define I2C_RETIMER_ADDR2 0x19
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH5 0xD
+
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/* QSPI device */
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE (1 << 26)
+#define FSL_QSPI_FLASH_NUM 2
+
+#endif
+
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS 1
+#define CONFIG_SF_DEFAULT_CS 0
+#endif
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_FSL_MEMAC
+
+/* MMC */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
+ QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
+
+/* Initial environment variables */
+#if defined(CONFIG_QSPI_BOOT)
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x90100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x1000000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
+ "sf read 0x80100000 0xE00000 0x100000;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000 \0"
+#else /* NOR BOOT */
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x90100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x1000000\0" \
+ "kernel_load=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0" \
+ "mcmemsize=0x70000000 \0"
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_FSL_MEMAC
+#define CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "DPMAC1@xgmii"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+#endif
+
+#undef CONFIG_CMDLINE_EDITING
+#include <config_distro_defaults.h>
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 0) \
+ func(SCSI, scsi, 0) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1088A_QDS_H */