arm: mvebu: turris_omnia: Add support for design with SW reset signals
New Turris Omnia HW board revision requires that software controls
peripheral reset signals, namely PERST# signals on mPCIe slots, ethernet
phy reset and lan switch reset. Those pins are connected to MCU controlled
by MCU i2c API as GPIOs. On new HW board revision those pins stay in reset
after board reset and software has to release these peripherals from reset
manually. MCU announce this requirement by FEAT_PERIPH_MCU bit in
CMD_GET_FEATURES command.
On older HW board revisions when FEAT_PERIPH_MCU is not announced, all
those reset signals are automatically released after board finish reset.
Detect FEAT_PERIPH_MCU bit in board_fix_fdt() and ft_board_setup()
functions and insert into device tree blob pcie "reset-gpios" and eth phy
"phy-reset-gpios" properties with corresponding MCU gpio definitions.
PCIe and eth PHY drivers then automatically release resets during device
initialization. Both U-Boot and Linux kernel drivers support those device
tree reset properties.
Initialization of lan switch on new HW board revision is more complicated.
Switch strapping pins are shared with switch RGMII pins. And strapping pins
must be in specific configuration after releasing switch reset. Due to pin
sharing, it is first required to switch A385 side of switch pins into GPIO
mode, set strapping configuration, release switch from reset and after that
switch A385 pins back to RGMII mode.
Because this complicated setup is not supported by switch DSA drivers and
cannot be expressed easily in device tree, implement it manually in SPL
function spl_board_init(). So in proper U-Boot and OS/kernel would be lan
switch initialized and be in same configuration like it was on old HW board
revisions (where reset sequence did those steps at hardware level).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index dab5711..a7c1c1f 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -19,9 +19,11 @@
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <dm/uclass.h>
+#include <dt-bindings/gpio/gpio.h>
#include <fdt_support.h>
#include <time.h>
#include <linux/bitops.h>
+#include <linux/delay.h>
#include <u-boot/crc.h>
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
@@ -65,6 +67,9 @@
/* available if STS_FEATURES_SUPPORTED bit set in status word */
CMD_GET_FEATURES = 0x10,
+
+ /* available if EXT_CMD bit set in features */
+ CMD_EXT_CONTROL = 0x12,
};
enum status_word_bits {
@@ -81,6 +86,16 @@
/* CMD_GET_FEATURES */
enum features_e {
FEAT_PERIPH_MCU = BIT(0),
+ FEAT_EXT_CMDS = BIT(1),
+};
+
+/* CMD_EXT_CONTROL */
+enum ext_ctl_e {
+ EXT_CTL_nRES_LAN = BIT(1),
+ EXT_CTL_nRES_PHY = BIT(2),
+ EXT_CTL_nPERST0 = BIT(3),
+ EXT_CTL_nPERST1 = BIT(4),
+ EXT_CTL_nPERST2 = BIT(5),
};
/*
@@ -543,6 +558,90 @@
}
}
+static void initialize_switch(void)
+{
+ u32 val, val04, val08, val10, val14;
+ u16 ctrl[2];
+ int err;
+
+ printf("Initializing LAN eth switch... ");
+
+ /* Change RGMII pins to GPIO mode */
+
+ val = val04 = readl(MVEBU_MPP_BASE + 0x04);
+ val &= ~GENMASK(19, 16); /* MPP[12] := GPIO */
+ val &= ~GENMASK(23, 20); /* MPP[13] := GPIO */
+ val &= ~GENMASK(27, 24); /* MPP[14] := GPIO */
+ val &= ~GENMASK(31, 28); /* MPP[15] := GPIO */
+ writel(val, MVEBU_MPP_BASE + 0x04);
+
+ val = val08 = readl(MVEBU_MPP_BASE + 0x08);
+ val &= ~GENMASK(3, 0); /* MPP[16] := GPIO */
+ val &= ~GENMASK(23, 20); /* MPP[21] := GPIO */
+ writel(val, MVEBU_MPP_BASE + 0x08);
+
+ val = val10 = readl(MVEBU_MPP_BASE + 0x10);
+ val &= ~GENMASK(27, 24); /* MPP[38] := GPIO */
+ val &= ~GENMASK(31, 28); /* MPP[39] := GPIO */
+ writel(val, MVEBU_MPP_BASE + 0x10);
+
+ val = val14 = readl(MVEBU_MPP_BASE + 0x14);
+ val &= ~GENMASK(3, 0); /* MPP[40] := GPIO */
+ val &= ~GENMASK(7, 4); /* MPP[41] := GPIO */
+ writel(val, MVEBU_MPP_BASE + 0x14);
+
+ /* Set initial values for switch reset strapping pins */
+
+ val = readl(MVEBU_GPIO0_BASE + 0x00);
+ val |= BIT(12); /* GPIO[12] := 1 */
+ val |= BIT(13); /* GPIO[13] := 1 */
+ val |= BIT(14); /* GPIO[14] := 1 */
+ val |= BIT(15); /* GPIO[15] := 1 */
+ val &= ~BIT(16); /* GPIO[16] := 0 */
+ val |= BIT(21); /* GPIO[21] := 1 */
+ writel(val, MVEBU_GPIO0_BASE + 0x00);
+
+ val = readl(MVEBU_GPIO1_BASE + 0x00);
+ val |= BIT(6); /* GPIO[38] := 1 */
+ val |= BIT(7); /* GPIO[39] := 1 */
+ val |= BIT(8); /* GPIO[40] := 1 */
+ val &= ~BIT(9); /* GPIO[41] := 0 */
+ writel(val, MVEBU_GPIO1_BASE + 0x00);
+
+ val = readl(MVEBU_GPIO0_BASE + 0x04);
+ val &= ~BIT(12); /* GPIO[12] := Out Enable */
+ val &= ~BIT(13); /* GPIO[13] := Out Enable */
+ val &= ~BIT(14); /* GPIO[14] := Out Enable */
+ val &= ~BIT(15); /* GPIO[15] := Out Enable */
+ val &= ~BIT(16); /* GPIO[16] := Out Enable */
+ val &= ~BIT(21); /* GPIO[21] := Out Enable */
+ writel(val, MVEBU_GPIO0_BASE + 0x04);
+
+ val = readl(MVEBU_GPIO1_BASE + 0x04);
+ val &= ~BIT(6); /* GPIO[38] := Out Enable */
+ val &= ~BIT(7); /* GPIO[39] := Out Enable */
+ val &= ~BIT(8); /* GPIO[40] := Out Enable */
+ val &= ~BIT(9); /* GPIO[41] := Out Enable */
+ writel(val, MVEBU_GPIO1_BASE + 0x04);
+
+ /* Release switch reset */
+
+ ctrl[0] = EXT_CTL_nRES_LAN;
+ ctrl[1] = EXT_CTL_nRES_LAN;
+ err = omnia_mcu_write(CMD_EXT_CONTROL, ctrl, sizeof(ctrl));
+
+ mdelay(10);
+
+ /* Change RGMII pins back to RGMII mode */
+
+ writel(val04, MVEBU_MPP_BASE + 0x04);
+ writel(val08, MVEBU_MPP_BASE + 0x08);
+ writel(val10, MVEBU_MPP_BASE + 0x10);
+ writel(val14, MVEBU_MPP_BASE + 0x14);
+
+ puts(err ? "failed\n" : "done\n");
+}
+
int board_early_init_f(void)
{
/* Configure MPP */
@@ -572,6 +671,9 @@
void spl_board_init(void)
{
+ u16 val;
+ int ret;
+
/*
* If booting from UART, disable MCU watchdog in SPL, since uploading
* U-Boot proper can take too much time and trigger it. Instead enable
@@ -581,6 +683,19 @@
enable_a385_watchdog(10);
disable_mcu_watchdog();
}
+
+ /*
+ * When MCU controls peripheral resets then release LAN eth switch from
+ * the reset and initialize it. When MCU does not control peripheral
+ * resets then LAN eth switch is initialized automatically by bootstrap
+ * pins when A385 is released from the reset.
+ */
+ ret = omnia_mcu_read(CMD_GET_STATUS_WORD, &val, sizeof(val));
+ if (ret == 0 && (val & STS_FEATURES_SUPPORTED)) {
+ ret = omnia_mcu_read(CMD_GET_FEATURES, &val, sizeof(val));
+ if (ret == 0 && (val & FEAT_PERIPH_MCU))
+ initialize_switch();
+ }
}
#if IS_ENABLED(CONFIG_OF_BOARD_FIXUP) || IS_ENABLED(CONFIG_OF_BOARD_SETUP)
@@ -689,11 +804,109 @@
disable_pcie_node(blob, 2);
}
+static int insert_mcu_gpio_prop(void *blob, int node, const char *prop,
+ unsigned int phandle, u32 bank, u32 gpio,
+ u32 flags)
+{
+ fdt32_t val[4] = { cpu_to_fdt32(phandle), cpu_to_fdt32(bank),
+ cpu_to_fdt32(gpio), cpu_to_fdt32(flags) };
+ return fdt_setprop(blob, node, prop, &val, sizeof(val));
+}
+
+static int fixup_mcu_gpio_in_pcie_nodes(void *blob)
+{
+ unsigned int mcu_phandle;
+ int port, gpio;
+ int pcie_node;
+ int port_node;
+ int ret;
+
+ ret = fdt_increase_size(blob, 128);
+ if (ret < 0) {
+ printf("Cannot increase FDT size!\n");
+ return ret;
+ }
+
+ mcu_phandle = fdt_create_phandle_by_compatible(blob, "cznic,turris-omnia-mcu");
+ if (!mcu_phandle)
+ return -FDT_ERR_NOPHANDLES;
+
+ fdt_for_each_node_by_compatible(pcie_node, blob, -1, "marvell,armada-370-pcie") {
+ if (!fdtdec_get_is_enabled(blob, pcie_node))
+ continue;
+
+ fdt_for_each_subnode(port_node, blob, pcie_node) {
+ if (!fdtdec_get_is_enabled(blob, port_node))
+ continue;
+
+ port = fdtdec_get_int(blob, port_node, "marvell,pcie-port", -1);
+
+ if (port == 0)
+ gpio = ilog2(EXT_CTL_nPERST0);
+ else if (port == 1)
+ gpio = ilog2(EXT_CTL_nPERST1);
+ else if (port == 2)
+ gpio = ilog2(EXT_CTL_nPERST2);
+ else
+ continue;
+
+ /* insert: reset-gpios = <&mcu 2 gpio GPIO_ACTIVE_LOW>; */
+ ret = insert_mcu_gpio_prop(blob, port_node, "reset-gpios",
+ mcu_phandle, 2, gpio, GPIO_ACTIVE_LOW);
+ if (ret < 0)
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int fixup_mcu_gpio_in_eth_wan_node(void *blob)
+{
+ unsigned int mcu_phandle;
+ int eth_wan_node;
+ int ret;
+
+ ret = fdt_increase_size(blob, 64);
+ if (ret < 0) {
+ printf("Cannot increase FDT size!\n");
+ return ret;
+ }
+
+ eth_wan_node = fdt_path_offset(blob, "ethernet2");
+ if (eth_wan_node < 0)
+ return eth_wan_node;
+
+ mcu_phandle = fdt_create_phandle_by_compatible(blob, "cznic,turris-omnia-mcu");
+ if (!mcu_phandle)
+ return -FDT_ERR_NOPHANDLES;
+
+ /* insert: phy-reset-gpios = <&mcu 2 gpio GPIO_ACTIVE_LOW>; */
+ ret = insert_mcu_gpio_prop(blob, eth_wan_node, "phy-reset-gpios",
+ mcu_phandle, 2, ilog2(EXT_CTL_nRES_PHY), GPIO_ACTIVE_LOW);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
#endif
#if IS_ENABLED(CONFIG_OF_BOARD_FIXUP)
int board_fix_fdt(void *blob)
{
+ u16 val;
+ int ret;
+
+ ret = omnia_mcu_read(CMD_GET_STATUS_WORD, &val, sizeof(val));
+ if (ret == 0 && (val & STS_FEATURES_SUPPORTED)) {
+ ret = omnia_mcu_read(CMD_GET_FEATURES, &val, sizeof(val));
+ if (ret == 0 && (val & FEAT_PERIPH_MCU)) {
+ fixup_mcu_gpio_in_pcie_nodes(blob);
+ fixup_mcu_gpio_in_eth_wan_node(blob);
+ }
+ }
+
fixup_msata_port_nodes(blob);
fixup_wwan_port_nodes(blob);
@@ -840,6 +1053,19 @@
int ft_board_setup(void *blob, struct bd_info *bd)
{
+ int node;
+
+ /*
+ * U-Boot's FDT blob contains phy-reset-gpios in ethernet2
+ * node when MCU controls all peripherals resets.
+ * Fixup MCU GPIO nodes in PCIe and eth wan nodes in this case.
+ */
+ node = fdt_path_offset(gd->fdt_blob, "ethernet2");
+ if (node >= 0 && fdt_getprop(gd->fdt_blob, node, "phy-reset-gpios", NULL)) {
+ fixup_mcu_gpio_in_pcie_nodes(blob);
+ fixup_mcu_gpio_in_eth_wan_node(blob);
+ }
+
fixup_spi_nor_partitions(blob);
fixup_msata_port_nodes(blob);
fixup_wwan_port_nodes(blob);