fdt: video: omap: add framebuffer and panel bindings
Add device-tree binding documentation for ti framebuffer and generic
panel output driver.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/doc/device-tree-bindings/video/tilcdc/panel.txt b/doc/device-tree-bindings/video/tilcdc/panel.txt
new file mode 100644
index 0000000..8082163
--- /dev/null
+++ b/doc/device-tree-bindings/video/tilcdc/panel.txt
@@ -0,0 +1,66 @@
+Device-Tree bindings for tilcdc DRM generic panel output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,panel".
+ - panel-info: configuration info to configure LCDC correctly for the panel
+ - ac-bias: AC Bias Pin Frequency
+ - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
+ - dma-burst-sz: DMA burst size
+ - bpp: Bits per pixel
+ - fdd: FIFO DMA Request Delay
+ - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
+ - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
+ - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
+ - fifo-th: DMA FIFO threshold
+ - display-timings: typical videomode of lcd panel. Multiple video modes
+ can be listed if the panel supports multiple timings, but the 'native-mode'
+ should be the preferred/default resolution. Refer to
+ Documentation/devicetree/bindings/display/panel/display-timing.txt for display
+ timing binding details.
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+- enable-gpios: GPIO pin to enable or disable the panel
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+ muxing properly for pins that connect to TFP410 device
+
+Example:
+
+ /* Settings for CDTech_S035Q01 / LCD3 cape: */
+ lcd3 {
+ compatible = "ti,tilcdc,panel";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio3 19 0>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <16>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 320x240 {
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <21>;
+ hfront-porch = <58>;
+ hsync-len = <47>;
+ vback-porch = <11>;
+ vfront-porch = <23>;
+ vsync-len = <2>;
+ clock-frequency = <8000000>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ };
+ };
+ };
diff --git a/doc/device-tree-bindings/video/tilcdc/tilcdc.txt b/doc/device-tree-bindings/video/tilcdc/tilcdc.txt
new file mode 100644
index 0000000..7bf1bb4
--- /dev/null
+++ b/doc/device-tree-bindings/video/tilcdc/tilcdc.txt
@@ -0,0 +1,82 @@
+Device-Tree bindings for tilcdc DRM driver
+
+Required properties:
+ - compatible: value should be one of the following:
+ - "ti,am33xx-tilcdc" for AM335x based boards
+ - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards
+ - interrupts: the interrupt number
+ - reg: base address and size of the LCDC device
+
+Recommended properties:
+ - ti,hwmods: Name of the hwmod associated to the LCDC
+
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+ interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+ the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+ by the lcd controller in KHz.
+ - blue-and-red-wiring: Recognized values "straight" or "crossed".
+ This property deals with the LCDC revision 2 (found on AM335x)
+ color errata [1].
+ - "straight" indicates normal wiring that supports RGB565,
+ BGR888, and XBGR8888 color formats.
+ - "crossed" indicates wiring that has blue and red wires
+ crossed. This setup supports BGR565, RGB888 and XRGB8888
+ formats.
+ - If the property is not present or its value is not recognized
+ the legacy mode is assumed. This configuration supports RGB565,
+ RGB888 and XRGB8888 formats. However, depending on wiring, the red
+ and blue colors are swapped in either 16 or 24-bit color modes.
+
+Optional nodes:
+
+ - port/ports: to describe a connection to an external encoder. The
+ binding follows Documentation/devicetree/bindings/graph.txt and
+ supports a single port with a single endpoint.
+
+ - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
+ Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting
+ tfp410 DVI encoder or lcd panel to lcdc
+
+[1] There is an errata about AM335x color wiring. For 16-bit color mode
+ the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
+ but for 24 bit color modes the wiring of blue and red components is
+ crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is
+ for Blue[3-7]. For more details see section 3.1.1 in AM335x
+ Silicon Errata:
+ http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
+
+Example:
+
+ fb: fb@4830e000 {
+ compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc";
+ reg = <0x4830e000 0x1000>;
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+ ti,hwmods = "lcdc";
+
+ blue-and-red-wiring = "crossed";
+
+ port {
+ lcdc_0: endpoint@0 {
+ remote-endpoint = <&hdmi_0>;
+ };
+ };
+ };
+
+ tda19988: tda19988 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+ port {
+ hdmi_0: endpoint@0 {
+ remote-endpoint = <&lcdc_0>;
+ };
+ };
+ };