diff --git a/include/configs/j721e_evm.h b/include/configs/j721e_evm.h
new file mode 100644
index 0000000..5b35e22
--- /dev/null
+++ b/include/configs/j721e_evm.h
@@ -0,0 +1,103 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration header file for K3 J721E EVM
+ *
+ * Copyright (C) 2018-2019 Texas Instruments Incorporated - http://www.ti.com/
+ *	Lokesh Vutla <lokeshvutla@ti.com>
+ */
+
+#ifndef __CONFIG_J721E_EVM_H
+#define __CONFIG_J721E_EVM_H
+
+#include <linux/sizes.h>
+#include <config_distro_bootcmd.h>
+#include <environment/ti/mmc.h>
+
+#define CONFIG_ENV_SIZE			(128 << 10)
+
+/* DDR Configuration */
+#define CONFIG_SYS_SDRAM_BASE1		0x880000000
+
+/* SPL Loader Configuration */
+#ifdef CONFIG_TARGET_J721E_A72_EVM
+#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SPL_TEXT_BASE +	\
+					 CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x280000
+#else
+/*
+ * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
+ * possible (to allow the build to go through), as this directly affects
+ * our memory footprint. The less we use for BSS the more we have available
+ * for everything else.
+ */
+#define CONFIG_SPL_BSS_MAX_SIZE		0xA000
+/*
+ * Link BSS to be within SPL in a dedicated region located near the top of
+ * the MCU SRAM, this way making it available also before relocation. Note
+ * that we are not using the actual top of the MCU SRAM as there is a memory
+ * location filled in by the boot ROM that we want to read out without any
+ * interference from the C context.
+ */
+#define CONFIG_SPL_BSS_START_ADDR	(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
+					 CONFIG_SPL_BSS_MAX_SIZE)
+/* Set the stack right below the SPL BSS section */
+#define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SPL_BSS_START_ADDR
+/* Configure R5 SPL post-relocation malloc pool in DDR */
+#define CONFIG_SYS_SPL_MALLOC_START	0x84000000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	SZ_16M
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x80000
+#endif
+
+#ifdef CONFIG_SYS_K3_SPL_ATF
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"tispl.bin"
+#endif
+
+#define CONFIG_SPL_MAX_SIZE		CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
+
+#define CONFIG_SYS_BOOTM_LEN		SZ_64M
+#define CONFIG_CQSPI_REF_CLK		133333333
+
+/* U-Boot general configuration */
+#define EXTRA_ENV_J721E_BOARD_SETTINGS					\
+	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"	\
+	"findfdt="							\
+		"setenv fdtfile ${default_device_tree};"		\
+		"setenv overlay_files ${name_overlays}\0"		\
+	"loadaddr=0x80080000\0"						\
+	"fdtaddr=0x82000000\0"						\
+	"overlayaddr=0x83000000\0"					\
+	"name_kern=Image\0"						\
+	"console=ttyS2,115200n8\0"					\
+	"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000\0" \
+	"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
+
+/* U-Boot MMC-specific configuration */
+#define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC				\
+	"boot=mmc\0"							\
+	"mmcdev=1\0"							\
+	"bootpart=1:2\0"						\
+	"bootdir=/boot\0"						\
+	"rd_spec=-\0"							\
+	"init_mmc=run args_all args_mmc\0"				\
+	"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+	"get_overlay_mmc="						\
+		"fdt address ${fdtaddr};"				\
+		"fdt resize 0x100000;"					\
+		"for overlay in $overlay_files;"			\
+		"do;"							\
+		"load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay} && "	\
+		"fdt apply ${overlayaddr};"				\
+		"done;\0"						\
+	"get_kern_mmc=load mmc ${bootpart} ${loadaddr} "		\
+		"${bootdir}/${name_kern}\0"
+
+/* Incorporate settings into the U-Boot environment */
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	DEFAULT_MMC_TI_ARGS						\
+	EXTRA_ENV_J721E_BOARD_SETTINGS					\
+	EXTRA_ENV_J721E_BOARD_SETTINGS_MMC
+
+/* Now for the remaining common defines */
+#include <configs/ti_armv7_common.h>
+
+#endif /* __CONFIG_J721E_EVM_H */