arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/arch/arm/dts/k3-j7200-som-p0.dtsi b/arch/arm/dts/k3-j7200-som-p0.dtsi
index ea5280d..7b5e9aa 100644
--- a/arch/arm/dts/k3-j7200-som-p0.dtsi
+++ b/arch/arm/dts/k3-j7200-som-p0.dtsi
@@ -11,8 +11,8 @@
memory@80000000 {
device_type = "memory";
/* 4G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
- <0x00000008 0x80000000 0x00000000 0x80000000>;
+ reg = <0x00 0x80000000 0x00 0x80000000>,
+ <0x08 0x80000000 0x00 0x80000000>;
};
reserved_memory: reserved-memory {
@@ -48,15 +48,112 @@
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+};
+
&hbmc {
+ /* OSPI and HBMC are muxed inside FSS, Bootloader will enable
+ * appropriate node based on board detection
+ */
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
- ranges = <0x0 0x0 0x5 0x0 0x4000000>, /* 64MB Flash on CS0 */
- <0x1 0x0 0x5 0x4000000 0x800000>; /* 8MB RAM on CS1 */
+ ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
+ <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
- reg = <0x0 0x0 0x4000000>;
+ reg = <0x00 0x00 0x4000000>;
+ };
+};
+
+&mailbox0_cluster0 {
+ interrupts = <436>;
+
+ mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+
+ mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+ ti,mbox-rx = <2 0 0>;
+ ti,mbox-tx = <3 0 0>;
+ };
+};
+
+&mailbox0_cluster1 {
+ interrupts = <432>;
+
+ mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+
+ mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+ ti,mbox-rx = <2 0 0>;
+ ti,mbox-tx = <3 0 0>;
+ };
+};
+
+&mailbox0_cluster2 {
+ status = "disabled";
+};
+
+&mailbox0_cluster3 {
+ status = "disabled";
+};
+
+&mailbox0_cluster4 {
+ status = "disabled";
+};
+
+&mailbox0_cluster5 {
+ status = "disabled";
+};
+
+&mailbox0_cluster6 {
+ status = "disabled";
+};
+
+&mailbox0_cluster7 {
+ status = "disabled";
+};
+
+&mailbox0_cluster8 {
+ status = "disabled";
+};
+
+&mailbox0_cluster9 {
+ status = "disabled";
+};
+
+&mailbox0_cluster10 {
+ status = "disabled";
+};
+
+&mailbox0_cluster11 {
+ status = "disabled";
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ exp_som: gpio@21 {
+ compatible = "ti,tca6408";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
+ "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
+ "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
+ "GPIO_LIN_EN", "CAN_STB";
};
};