Patch by Wolter Kamphuis, 05 Dec 2003:
Add support for SNMC's QS850/QS823/QS860T boards
diff --git a/include/commproc.h b/include/commproc.h
index 63dcc4c..3da804f 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -1216,6 +1216,60 @@
#endif /* CONFIG_NETVIA */
+/*** QS850/QS823 ***************************************************/
+
+#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
+#undef FEC_ENET /* Don't use FEC for EThernet */
+
+#define PROFF_ENET PROFF_SCC2
+#define CPM_CR_ENET CPM_CR_CH_SCC2
+#define SCC_ENET 1
+
+#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
+#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
+#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
+#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
+#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
+#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
+#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
+#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
+#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
+#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
+
+/* SCC2 TXCLK from CLK2
+ * SCC2 RXCLK from CLK4
+ * SCC2 Connected to NMSI */
+#define SICR_ENET_MASK ((uint)0x00007F00)
+#define SICR_ENET_CLKRT ((uint)0x00003D00)
+
+#endif /* CONFIG_QS850/QS823 */
+
+/*** QS860T ***************************************************/
+
+#ifdef CONFIG_QS860T
+#ifdef CONFIG_FEC_ENET
+#define FEC_ENET /* use FEC for EThernet */
+#endif /* CONFIG_FEC_ETHERNET */
+
+/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
+#define PROFF_ENET PROFF_SCC1
+#define CPM_CR_ENET CPM_CR_CH_SCC1
+#define SCC_ENET 0
+
+#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
+#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
+#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
+#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
+#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
+#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
+#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
+
+#define SICR_ENET_MASK ((uint)0x000000ff)
+/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
+#define SICR_ENET_CLKRT ((uint)0x0000003D)
+
+#endif /* CONFIG_QS860T */
+
/*** RPXCLASSIC *****************************************************/
#ifdef CONFIG_RPXCLASSIC
@@ -1452,6 +1506,7 @@
#define SICR_ENET_CLKRT ((uint)0x00002e00)
#endif /* CONFIG_V37 */
+
/*********************************************************************/
/* SCC Event register as used by Ethernet.
diff --git a/include/configs/QS823.h b/include/configs/QS823.h
new file mode 100644
index 0000000..235bc48
--- /dev/null
+++ b/include/configs/QS823.h
@@ -0,0 +1,571 @@
+/*
+ * (C) Copyright 2003
+ * MuLogic B.V.
+ *
+ * (C) Copyright 2002
+ * Simple Network Magic Corporation
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* various debug settings */
+#undef CFG_DEVICE_NULLDEV /* null device */
+#undef CONFIG_SILENT_CONSOLE /* silent console */
+#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
+#undef DEBUG /* debug output code */
+#undef DEBUG_FLASH /* debug flash code */
+#undef FLASH_DEBUG /* debug fash code */
+#undef DEBUG_ENV /* debug environment code */
+
+#define CFG_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
+#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
+#define CONFIG_QS823 1 /* ...on a QS823 module */
+#define CONFIG_SCC2_ENET 1 /* SCC2 10BaseT ethernet */
+
+/* Select the target clock speed */
+#undef CONFIG_CLOCK_16MHZ /* cpu=16,777,216 Hz, mem=16Mhz */
+#undef CONFIG_CLOCK_33MHZ /* cpu=33,554,432 Hz, mem=33Mhz */
+#undef CONFIG_CLOCK_50MHZ /* cpu=49,971,200 Hz, mem=33Mhz */
+#define CONFIG_CLOCK_66MHZ 1 /* cpu=67,108,864 Hz, mem=66Mhz */
+#undef CONFIG_CLOCK_80MHZ /* cpu=79,986,688 Hz, mem=33Mhz */
+
+#ifdef CONFIG_CLOCK_16MHZ
+#define CONFIG_CLOCK_MULT 512
+#endif
+
+#ifdef CONFIG_CLOCK_33MHZ
+#define CONFIG_CLOCK_MULT 1024
+#endif
+
+#ifdef CONFIG_CLOCK_50MHZ
+#define CONFIG_CLOCK_MULT 1525
+#endif
+
+#ifdef CONFIG_CLOCK_66MHZ
+#define CONFIG_CLOCK_MULT 2048
+#endif
+
+#ifdef CONFIG_CLOCK_80MHZ
+#define CONFIG_CLOCK_MULT 2441
+#endif
+
+/* choose flash size, 4Mb or 8Mb */
+#define CONFIG_FLASH_4MB 1 /* board has 4Mb flash */
+#undef CONFIG_FLASH_8MB /* board has 8Mb flash */
+
+#define CONFIG_CLOCK_BASE 32768 /* Base clock input freq */
+
+#undef CONFIG_8xx_CONS_SMC1
+#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
+
+#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
+
+/* Define default IP addresses */
+#define CONFIG_IPADDR 192.168.1.99 /* own ip address */
+#define CONFIG_SERVERIP 192.168.1.19 /* used for tftp (not nfs?) */
+
+/* message to say directly after booting */
+#define CONFIG_PREBOOT "echo '';" \
+ "echo 'type:';" \
+ "echo 'run boot_nfs to boot to NFS';" \
+ "echo 'run boot_flash to boot to flash';" \
+ "echo '';" \
+ "echo 'run flash_rootfs to install a new rootfs';" \
+ "echo 'run flash_env to clear the env sector';" \
+ "echo 'run flash_rw to clear the rw fs';" \
+ "echo 'run flash_uboot to install a new u-boot';" \
+ "echo 'run flash_kernel to install a new kernel';"
+
+/* wait 5 seconds before executing CONFIG_BOOTCOMMAND */
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOTCOMMAND "run boot_nfs"
+
+#undef CONFIG_BOOTARGS /* made by set_nfs of set_flash */
+
+/* Our flash filesystem looks like this
+ *
+ * 4Mb board:
+ * ffc0 0000 - ffeb ffff root filesystem (jffs2) (~3Mb)
+ * ffec 0000 - ffed ffff read-write filesystem (ext2)
+ * ffee 0000 - ffef ffff environment
+ * fff0 0000 - fff1 ffff u-boot
+ * fff2 0000 - ffff ffff linux kernel
+ *
+ * 8Mb board:
+ * ff80 0000 - ffeb ffff root filesystem (jffs2) (~7Mb)
+ * ffec 0000 - ffed ffff read-write filesystem (ext2)
+ * ffee 0000 - ffef ffff environment
+ * fff0 0000 - fff1 ffff u-boot
+ * fff2 0000 - ffff ffff linux kernel
+ *
+ */
+
+/* environment for 4Mb board */
+#ifdef CONFIG_FLASH_4MB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "serial#=QS823\0" \
+ "hostname=qs823\0" \
+ "netdev=eth0\0" \
+ "ethaddr=00:01:02:B4:36:56\0" \
+ "rootpath=/exports/rootfs\0" \
+ "mtdparts=mtdparts=phys:2816k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
+ /* fill in variables */ \
+ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
+ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
+ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
+ /* commands */ \
+ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
+ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
+ /* reinstall flash parts */ \
+ "flash_rootfs=protect off ffc00000 ffebffff; era ffc00000 ffebffff; tftp ffc00000 /tftpboot/rootfs.jffs2\0" \
+ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
+ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
+ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.4mb.bin\0" \
+ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
+#endif /* CONFIG_FLASH_4MB */
+
+/* environment for 8Mb board */
+#ifdef CONFIG_FLASH_8MB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "serial#=QS823\0" \
+ "hostname=qs823\0" \
+ "netdev=eth0\0" \
+ "ethaddr=00:01:02:B4:36:56\0" \
+ "rootpath=/exports/rootfs\0" \
+ "mtdparts=mtdparts=phys:6912k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
+ /* fill in variables */ \
+ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
+ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
+ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
+ /* commands */ \
+ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
+ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
+ /* reinstall flash parts */ \
+ "flash_rootfs=protect off ff800000 ffebffff; era ff800000 ffebffff; tftp ff800000 /tftpboot/rootfs.jffs2\0" \
+ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
+ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
+ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.8mb.bin\0" \
+ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
+#endif /* CONFIG_FLASH_8MB */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_STATUS_LED /* Status LED disabled */
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#undef CONFIG_MAC_PARTITION
+#undef CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS (CFG_CMD_BDI | \
+ CFG_CMD_BOOTD | \
+ CFG_CMD_CONSOLE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_ENV | \
+ CFG_CMD_FLASH | \
+ CFG_CMD_IMI | \
+ CFG_CMD_IMMAP | \
+ CFG_CMD_MEMORY | \
+ CFG_CMD_NET | \
+ CFG_CMD_RUN)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*-----------------------------------------------------------------------
+ * Environment variable storage is in FLASH, one sector before U-boot
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE 0x20000 /* 128Kb, one whole sector */
+#define CFG_ENV_SIZE 0x2000 /* 8kb */
+#define CFG_ENV_ADDR 0xffee0000 /* address of env sector */
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x400000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF800000 /* Allow an 8Mbyte window */
+
+#define FLASH_BASE0_4M_PRELIM 0xFFC00000 /* Base for 4M Flash */
+#define FLASH_BASE0_8M_PRELIM 0xFF800000 /* Base for 8M Flash */
+
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MONITOR_BASE 0xFFF00000 /* U-boot location */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * TODO flash parameters
+ * FLASH organization for Intel Strataflash
+ */
+#undef CFG_FLASH_16BIT /* 32-bit wide flash memory */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+
+#ifdef CONFIG_WATCHDOG
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWRI | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR (SIUMCR_DLK | SIUMCR_DPC | SIUMCR_MPRE | SIUMCR_MLRC01 | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ */
+
+/* MF (Multiplication Factor of SPLL) */
+/* Sets the QS823 to specified clock from 32KHz clock at EXTAL. */
+#define vPLPRCR_MF ((CONFIG_CLOCK_MULT+1) << 20)
+#define CFG_PLPRCR (vPLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | PLPRCR_LOLRE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ */
+#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG00)
+#define CFG_BRGCLK_PRESCALE 1
+#endif
+
+#if defined(CONFIG_CLOCK_66MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG01)
+#define CFG_BRGCLK_PRESCALE 4
+#endif
+
+#if defined(CONFIG_CLOCK_80MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF01 | SCCR_DFBRG01)
+#define CFG_BRGCLK_PRESCALE 4
+#endif
+
+#define SCCR_MASK CFG_SCCR
+
+/*-----------------------------------------------------------------------
+ * Debug Enable Register
+ * 0x73E67C0F - All interrupts handled by BDM
+ * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
+ *-----------------------------------------------------------------------
+#define CFG_DER 0x73E67C0F
+#define CFG_DER 0x0082400F
+
+ #-------------------------------------------------------------------------
+ # Program the Debug Enable Register (DER). This register provides the user
+ # with the reason for entering into the debug mode. We want all conditions
+ # to end up as an exception. We don't want to enter into debug mode for
+ # any condition. See the back of of the Development Support section of the
+ # MPC860 User Manual for a description of this register.
+ #-------------------------------------------------------------------------
+*/
+#define CFG_DER 0
+
+/*-----------------------------------------------------------------------
+ * Memory Controller Initialization Constants
+ *-----------------------------------------------------------------------
+ */
+
+/*
+ * BR0 and OR0 (AMD dual FLASH devices)
+ * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
+ */
+#define CFG_PRELIM_OR_AM
+#define CFG_OR_TIMING_FLASH
+
+/*
+ *-----------------------------------------------------------------------
+ * Base Register 0 (BR0): Bank 0 is assigned to the 8Mbyte (2M X 32)
+ * flash that resides on the QS823.
+ *-----------------------------------------------------------------------
+ */
+
+/* BA (Base Address) = 0xFF80+0b for a total of 17 bits. 17 bit base addr */
+/* represents a minumum 32K block size. */
+#define vBR0_BA ((0xFF80 << 16) + (0 << 15))
+#define CFG_BR0_PRELIM (vBR0_BA | BR_V)
+
+/* AM (Address Mask) = 0xFF80+0b = We've masked the upper 9 bits */
+/* which defines a 8 Mbyte memory block. */
+#define vOR0_AM ((0xFF80 << 16) + (0 << 15))
+
+#if defined(CONFIG_CLOCK_50MHZ) || defined(CONFIG_CLOCK_80MHZ)
+/* 0101 = Add a 5 clock cycle wait state */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | 0R_ACS_DIV4 | OR_BI | OR_SCY_5_CLK)
+#endif
+
+#if defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_66MHZ)
+/* 0011 = Add a 3 clock cycle wait state */
+/* 29.8ns clock * (3 + 2) = 149ns cycle time */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK)
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ)
+/* 0010 = Add a 2 clock cycle wait state */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_2_CLK)
+#endif
+
+/*
+ * BR1 and OR1 (SDRAM)
+ * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
+ * Base Address = 0x00000000 - 0x01FF_FFFF (32M After relocation)
+ * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
+ * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
+ */
+
+#define SDRAM_BASE 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+
+/* AM (Address Mask) = 0xF800+0b = We've masked the upper 5 bits which
+ * represents a 128 Mbyte block the DRAM in
+ * this address base.
+ */
+#define vOR1_AM ((0xF800 << 16) + (0 << 15))
+#define vBR1_BA ((0x0000 << 16) + (0 << 15))
+#define CFG_OR1 (vOR1_AM | OR_CSNT_SAM | OR_BI)
+#define CFG_BR1 (vBR1_BA | BR_MS_UPMA | BR_V)
+
+/* Machine A Mode Register */
+
+/* PTA Periodic Timer A */
+
+#if defined(CONFIG_CLOCK_80MHZ)
+#define vMAMR_PTA (19 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_66MHZ)
+#define vMAMR_PTA (16 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_50MHZ)
+#define vMAMR_PTA (195 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_33MHZ)
+#define vMAMR_PTA (131 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ)
+#define vMAMR_PTA (65 << 24)
+#endif
+
+/* For boards with 16M of SDRAM */
+#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
+#define CFG_16M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_0 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A11 |\
+MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/* For boards with 32M of SDRAM */
+#define SDRAM_32M_MAX_SIZE 0x02000000 /* max 32MB SDRAM */
+#define CFG_32M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_1 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A10 |\
+MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+
+/* Memory Periodic Timer Prescaler Register */
+
+#if defined(CONFIG_CLOCK_66MHZ) || defined(CONFIG_CLOCK_80MHZ)
+/* Divide by 32 */
+#define CFG_MPTPR 0x02
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
+/* Divide by 16 */
+#define CFG_MPTPR 0x04
+#endif
+
+/*
+ * BR2 and OR2 (Unused)
+ * Base address = 0xF020_0000 - 0xF020_0FFF
+ *
+ */
+#define CFG_OR2_PRELIM 0xFFF00000
+#define CFG_BR2_PRELIM 0xF0200000
+
+/*
+ * BR3 and OR3 (External Bus CS3)
+ * Base address = 0xF030_0000 - 0xF030_0FFF
+ *
+ */
+#define CFG_OR3_PRELIM 0xFFF00000
+#define CFG_BR3_PRELIM 0xF0300000
+
+/*
+ * BR4 and OR4 (External Bus CS3)
+ * Base address = 0xF040_0000 - 0xF040_0FFF
+ *
+ */
+#define CFG_OR4_PRELIM 0xFFF00000
+#define CFG_BR4_PRELIM 0xF0400000
+
+
+/*
+ * BR4 and OR4 (External Bus CS3)
+ * Base address = 0xF050_0000 - 0xF050_0FFF
+ *
+ */
+#define CFG_OR5_PRELIM 0xFFF00000
+#define CFG_BR5_PRELIM 0xF0500000
+
+/*
+ * BR6 and OR6 (Unused)
+ * Base address = 0xF060_0000 - 0xF060_0FFF
+ *
+ */
+#define CFG_OR6_PRELIM 0xFFF00000
+#define CFG_BR6_PRELIM 0xF0600000
+
+/*
+ * BR7 and OR7 (Unused)
+ * Base address = 0xF070_0000 - 0xF070_0FFF
+ *
+ */
+#define CFG_OR7_PRELIM 0xFFF00000
+#define CFG_BR7_PRELIM 0xF0700000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Sanity checks
+ */
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/QS850.h b/include/configs/QS850.h
new file mode 100644
index 0000000..967582b
--- /dev/null
+++ b/include/configs/QS850.h
@@ -0,0 +1,571 @@
+/*
+ * (C) Copyright 2003
+ * MuLogic B.V.
+ *
+ * (C) Copyright 2002
+ * Simple Network Magic Corporation
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* various debug settings */
+#undef CFG_DEVICE_NULLDEV /* null device */
+#undef CONFIG_SILENT_CONSOLE /* silent console */
+#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
+#undef DEBUG /* debug output code */
+#undef DEBUG_FLASH /* debug flash code */
+#undef FLASH_DEBUG /* debug fash code */
+#undef DEBUG_ENV /* debug environment code */
+
+#define CFG_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
+#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
+#define CONFIG_QS850 1 /* ...on a QS850 module */
+#define CONFIG_SCC2_ENET 1 /* SCC2 10BaseT ethernet */
+
+/* Select the target clock speed */
+#undef CONFIG_CLOCK_16MHZ /* cpu=16,777,216 Hz, mem=16Mhz */
+#undef CONFIG_CLOCK_33MHZ /* cpu=33,554,432 Hz, mem=33Mhz */
+#undef CONFIG_CLOCK_50MHZ /* cpu=49,971,200 Hz, mem=33Mhz */
+#define CONFIG_CLOCK_66MHZ 1 /* cpu=67,108,864 Hz, mem=66Mhz */
+#undef CONFIG_CLOCK_80MHZ /* cpu=79,986,688 Hz, mem=33Mhz */
+
+#ifdef CONFIG_CLOCK_16MHZ
+#define CONFIG_CLOCK_MULT 512
+#endif
+
+#ifdef CONFIG_CLOCK_33MHZ
+#define CONFIG_CLOCK_MULT 1024
+#endif
+
+#ifdef CONFIG_CLOCK_50MHZ
+#define CONFIG_CLOCK_MULT 1525
+#endif
+
+#ifdef CONFIG_CLOCK_66MHZ
+#define CONFIG_CLOCK_MULT 2048
+#endif
+
+#ifdef CONFIG_CLOCK_80MHZ
+#define CONFIG_CLOCK_MULT 2441
+#endif
+
+/* choose flash size, 4Mb or 8Mb */
+#define CONFIG_FLASH_4MB 1 /* board has 4Mb flash */
+#undef CONFIG_FLASH_8MB /* board has 8Mb flash */
+
+#define CONFIG_CLOCK_BASE 32768 /* Base clock input freq */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
+
+#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
+
+/* Define default IP addresses */
+#define CONFIG_IPADDR 192.168.1.99 /* own ip address */
+#define CONFIG_SERVERIP 192.168.1.19 /* used for tftp (not nfs?) */
+
+/* message to say directly after booting */
+#define CONFIG_PREBOOT "echo '';" \
+ "echo 'type:';" \
+ "echo 'run boot_nfs to boot to NFS';" \
+ "echo 'run boot_flash to boot to flash';" \
+ "echo '';" \
+ "echo 'run flash_rootfs to install a new rootfs';" \
+ "echo 'run flash_env to clear the env sector';" \
+ "echo 'run flash_rw to clear the rw fs';" \
+ "echo 'run flash_uboot to install a new u-boot';" \
+ "echo 'run flash_kernel to install a new kernel';"
+
+/* wait 5 seconds before executing CONFIG_BOOTCOMMAND */
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOTCOMMAND "run boot_nfs"
+
+#undef CONFIG_BOOTARGS /* made by set_nfs of set_flash */
+
+/* Our flash filesystem looks like this
+ *
+ * 4Mb board:
+ * ffc0 0000 - ffeb ffff root filesystem (jffs2) (~3Mb)
+ * ffec 0000 - ffed ffff read-write filesystem (ext2)
+ * ffee 0000 - ffef ffff environment
+ * fff0 0000 - fff1 ffff u-boot
+ * fff2 0000 - ffff ffff linux kernel
+ *
+ * 8Mb board:
+ * ff80 0000 - ffeb ffff root filesystem (jffs2) (~7Mb)
+ * ffec 0000 - ffed ffff read-write filesystem (ext2)
+ * ffee 0000 - ffef ffff environment
+ * fff0 0000 - fff1 ffff u-boot
+ * fff2 0000 - ffff ffff linux kernel
+ *
+ */
+
+/* environment for 4Mb board */
+#ifdef CONFIG_FLASH_4MB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "serial#=QS850\0" \
+ "hostname=qs850\0" \
+ "netdev=eth0\0" \
+ "ethaddr=00:01:02:B4:36:56\0" \
+ "rootpath=/exports/rootfs\0" \
+ "mtdparts=mtdparts=phys:2816k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
+ /* fill in variables */ \
+ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
+ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
+ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
+ /* commands */ \
+ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
+ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
+ /* reinstall flash parts */ \
+ "flash_rootfs=protect off ffc00000 ffebffff; era ffc00000 ffebffff; tftp ffc00000 /tftpboot/rootfs.jffs2\0" \
+ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
+ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
+ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.4mb.bin\0" \
+ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
+#endif /* CONFIG_FLASH_4MB */
+
+/* environment for 8Mb board */
+#ifdef CONFIG_FLASH_8MB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "serial#=QS850\0" \
+ "hostname=qs850\0" \
+ "netdev=eth0\0" \
+ "ethaddr=00:01:02:B4:36:56\0" \
+ "rootpath=/exports/rootfs\0" \
+ "mtdparts=mtdparts=phys:6912k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
+ /* fill in variables */ \
+ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
+ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
+ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
+ /* commands */ \
+ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
+ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
+ /* reinstall flash parts */ \
+ "flash_rootfs=protect off ff800000 ffebffff; era ff800000 ffebffff; tftp ff800000 /tftpboot/rootfs.jffs2\0" \
+ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
+ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
+ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.8mb.bin\0" \
+ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
+#endif /* CONFIG_FLASH_8MB */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_STATUS_LED /* Status LED disabled */
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#undef CONFIG_MAC_PARTITION
+#undef CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS (CFG_CMD_BDI | \
+ CFG_CMD_BOOTD | \
+ CFG_CMD_CONSOLE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_ENV | \
+ CFG_CMD_FLASH | \
+ CFG_CMD_IMI | \
+ CFG_CMD_IMMAP | \
+ CFG_CMD_MEMORY | \
+ CFG_CMD_NET | \
+ CFG_CMD_RUN)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*-----------------------------------------------------------------------
+ * Environment variable storage is in FLASH, one sector before U-boot
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE 0x20000 /* 128Kb, one whole sector */
+#define CFG_ENV_SIZE 0x2000 /* 8kb */
+#define CFG_ENV_ADDR 0xffee0000 /* address of env sector */
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x400000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF800000 /* Allow an 8Mbyte window */
+
+#define FLASH_BASE0_4M_PRELIM 0xFFC00000 /* Base for 4M Flash */
+#define FLASH_BASE0_8M_PRELIM 0xFF800000 /* Base for 8M Flash */
+
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MONITOR_BASE 0xFFF00000 /* U-boot location */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * TODO flash parameters
+ * FLASH organization for Intel Strataflash
+ */
+#undef CFG_FLASH_16BIT /* 32-bit wide flash memory */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+
+#ifdef CONFIG_WATCHDOG
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWRI | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR (SIUMCR_DLK | SIUMCR_DPC | SIUMCR_MPRE | SIUMCR_MLRC01 | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ */
+
+/* MF (Multiplication Factor of SPLL) */
+/* Sets the QS850 to specified clock from 32KHz clock at EXTAL. */
+#define vPLPRCR_MF ((CONFIG_CLOCK_MULT+1) << 20)
+#define CFG_PLPRCR (vPLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | PLPRCR_LOLRE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ */
+#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG00)
+#define CFG_BRGCLK_PRESCALE 1
+#endif
+
+#if defined(CONFIG_CLOCK_66MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG01)
+#define CFG_BRGCLK_PRESCALE 4
+#endif
+
+#if defined(CONFIG_CLOCK_80MHZ)
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF01 | SCCR_DFBRG01)
+#define CFG_BRGCLK_PRESCALE 4
+#endif
+
+#define SCCR_MASK CFG_SCCR
+
+/*-----------------------------------------------------------------------
+ * Debug Enable Register
+ * 0x73E67C0F - All interrupts handled by BDM
+ * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
+ *-----------------------------------------------------------------------
+#define CFG_DER 0x73E67C0F
+#define CFG_DER 0x0082400F
+
+ #-------------------------------------------------------------------------
+ # Program the Debug Enable Register (DER). This register provides the user
+ # with the reason for entering into the debug mode. We want all conditions
+ # to end up as an exception. We don't want to enter into debug mode for
+ # any condition. See the back of of the Development Support section of the
+ # MPC860 User Manual for a description of this register.
+ #-------------------------------------------------------------------------
+*/
+#define CFG_DER 0
+
+/*-----------------------------------------------------------------------
+ * Memory Controller Initialization Constants
+ *-----------------------------------------------------------------------
+ */
+
+/*
+ * BR0 and OR0 (AMD dual FLASH devices)
+ * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
+ */
+#define CFG_PRELIM_OR_AM
+#define CFG_OR_TIMING_FLASH
+
+/*
+ *-----------------------------------------------------------------------
+ * Base Register 0 (BR0): Bank 0 is assigned to the 8Mbyte (2M X 32)
+ * flash that resides on the QS850.
+ *-----------------------------------------------------------------------
+ */
+
+/* BA (Base Address) = 0xFF80+0b for a total of 17 bits. 17 bit base addr */
+/* represents a minumum 32K block size. */
+#define vBR0_BA ((0xFF80 << 16) + (0 << 15))
+#define CFG_BR0_PRELIM (vBR0_BA | BR_V)
+
+/* AM (Address Mask) = 0xFF80+0b = We've masked the upper 9 bits */
+/* which defines a 8 Mbyte memory block. */
+#define vOR0_AM ((0xFF80 << 16) + (0 << 15))
+
+#if defined(CONFIG_CLOCK_50MHZ) || defined(CONFIG_CLOCK_80MHZ)
+/* 0101 = Add a 5 clock cycle wait state */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | 0R_ACS_DIV4 | OR_BI | OR_SCY_5_CLK)
+#endif
+
+#if defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_66MHZ)
+/* 0011 = Add a 3 clock cycle wait state */
+/* 29.8ns clock * (3 + 2) = 149ns cycle time */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK)
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ)
+/* 0010 = Add a 2 clock cycle wait state */
+#define CFG_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_2_CLK)
+#endif
+
+/*
+ * BR1 and OR1 (SDRAM)
+ * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
+ * Base Address = 0x00000000 - 0x01FF_FFFF (32M After relocation)
+ * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
+ * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
+ */
+
+#define SDRAM_BASE 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+
+/* AM (Address Mask) = 0xF800+0b = We've masked the upper 5 bits which
+ * represents a 128 Mbyte block the DRAM in
+ * this address base.
+ */
+#define vOR1_AM ((0xF800 << 16) + (0 << 15))
+#define vBR1_BA ((0x0000 << 16) + (0 << 15))
+#define CFG_OR1 (vOR1_AM | OR_CSNT_SAM | OR_BI)
+#define CFG_BR1 (vBR1_BA | BR_MS_UPMA | BR_V)
+
+/* Machine A Mode Register */
+
+/* PTA Periodic Timer A */
+
+#if defined(CONFIG_CLOCK_80MHZ)
+#define vMAMR_PTA (19 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_66MHZ)
+#define vMAMR_PTA (16 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_50MHZ)
+#define vMAMR_PTA (195 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_33MHZ)
+#define vMAMR_PTA (131 << 24)
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ)
+#define vMAMR_PTA (65 << 24)
+#endif
+
+/* For boards with 16M of SDRAM */
+#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
+#define CFG_16M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_0 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A11 |\
+MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/* For boards with 32M of SDRAM */
+#define SDRAM_32M_MAX_SIZE 0x02000000 /* max 32MB SDRAM */
+#define CFG_32M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_1 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A10 |\
+MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+
+/* Memory Periodic Timer Prescaler Register */
+
+#if defined(CONFIG_CLOCK_66MHZ) || defined(CONFIG_CLOCK_80MHZ)
+/* Divide by 32 */
+#define CFG_MPTPR 0x02
+#endif
+
+#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
+/* Divide by 16 */
+#define CFG_MPTPR 0x04
+#endif
+
+/*
+ * BR2 and OR2 (Unused)
+ * Base address = 0xF020_0000 - 0xF020_0FFF
+ *
+ */
+#define CFG_OR2_PRELIM 0xFFF00000
+#define CFG_BR2_PRELIM 0xF0200000
+
+/*
+ * BR3 and OR3 (External Bus CS3)
+ * Base address = 0xF030_0000 - 0xF030_0FFF
+ *
+ */
+#define CFG_OR3_PRELIM 0xFFF00000
+#define CFG_BR3_PRELIM 0xF0300000
+
+/*
+ * BR4 and OR4 (External Bus CS3)
+ * Base address = 0xF040_0000 - 0xF040_0FFF
+ *
+ */
+#define CFG_OR4_PRELIM 0xFFF00000
+#define CFG_BR4_PRELIM 0xF0400000
+
+
+/*
+ * BR4 and OR4 (External Bus CS3)
+ * Base address = 0xF050_0000 - 0xF050_0FFF
+ *
+ */
+#define CFG_OR5_PRELIM 0xFFF00000
+#define CFG_BR5_PRELIM 0xF0500000
+
+/*
+ * BR6 and OR6 (Unused)
+ * Base address = 0xF060_0000 - 0xF060_0FFF
+ *
+ */
+#define CFG_OR6_PRELIM 0xFFF00000
+#define CFG_BR6_PRELIM 0xF0600000
+
+/*
+ * BR7 and OR7 (Unused)
+ * Base address = 0xF070_0000 - 0xF070_0FFF
+ *
+ */
+#define CFG_OR7_PRELIM 0xFFF00000
+#define CFG_BR7_PRELIM 0xF0700000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Sanity checks
+ */
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/QS860T.h b/include/configs/QS860T.h
new file mode 100644
index 0000000..92eccd3
--- /dev/null
+++ b/include/configs/QS860T.h
@@ -0,0 +1,413 @@
+/*
+ * (C) Copyright 2003
+ * MuLogic B.V.
+ *
+ * (C) Copyright 2002
+ * Simple Network Magic Corporation
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* various debug settings */
+#undef CFG_DEVICE_NULLDEV /* null device */
+#undef CONFIG_SILENT_CONSOLE /* silent console */
+#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
+#undef DEBUG /* debug output code */
+#undef DEBUG_FLASH /* debug flash code */
+#undef FLASH_DEBUG /* debug fash code */
+#undef DEBUG_ENV /* debug environment code */
+
+#define CFG_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
+#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
+
+
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
+#define CONFIG_QS860T 1 /* ...on a QS860T module */
+
+#define CONFIG_FEC_ENET 1 /* FEC 10/100BaseT ethernet */
+#define FEC_INTERRUPT SIU_LEVEL1
+#undef CONFIG_SCC1_ENET /* SCC1 10BaseT ethernet */
+#define CFG_DISCOVER_PHY
+
+#undef CONFIG_8xx_CONS_SMC1
+#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC */
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+/* Pass clocks to Linux 2.4.18 in Hz */
+#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo 'Type \"run flash_nfs\" to mount root filesystem over NFS';" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+/* TODO compare against CADM860 */
+#define CONFIG_BOOTCOMMAND "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#undef CONFIG_STATUS_LED /* Status LED disabled */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_IMMAP | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_NET | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DATE )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+/* TODO */
+#if 0
+/* Look at these */
+CONFIG_IPADDR
+CONFIG_SERVERIP
+CONFIG_I2C
+CONFIG_SPI
+#endif
+
+/*
+ * Environment variable storage is in NVRAM
+ */
+#define CFG_ENV_IS_IN_NVRAM 1
+#define CFG_ENV_SIZE 0x00001000 /* We use only the last 4K for PPCBoot */
+#define CFG_ENV_ADDR 0xD100E000
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+/* TODO - size? */
+#define CFG_MEMTEST_START 0x0400000 /* memtest works */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFF00000
+
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/* TODO flash parameters */
+/*-----------------------------------------------------------------------
+ * FLASH organization for Intel Strataflash
+ */
+#define CFG_FLASH_16BIT 1 /* 16-bit wide flash memory */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#undef CFG_ENV_IS_IN_FLASH
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (0xFFFFFF88 | SYPCR_SWE | SYPCR_SWRI)
+#else
+#define CFG_SYPCR 0xFFFFFF88
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR 0x00620000
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ */
+#define CFG_TBSCR 0x00C3
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PISCR 0x0082
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PLPRCR 0x0090D000
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR 0x02000000
+
+
+/*-----------------------------------------------------------------------
+ * Debug Enable Register
+ * 0x73E67C0F - All interrupts handled by BDM
+ * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
+ *-----------------------------------------------------------------------
+#define CFG_DER 0x73E67C0F
+*/
+#define CFG_DER 0x0082400F
+
+
+/*-----------------------------------------------------------------------
+ * Memory Controller Initialization Constants
+ *-----------------------------------------------------------------------
+ */
+
+/*
+ * BR0 and OR0 (AMD 512K Socketed FLASH)
+ * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
+ */
+#define CFG_PRELIM_OR_AM
+#define CFG_OR_TIMING_FLASH
+
+#define FLASH_BASE0_PRELIM 0xFFF00001
+#define CFG_OR0_PRELIM 0xFFF80D42
+#define CFG_BR0_PRELIM 0xFFF00401
+
+
+/*
+ * BR1 and OR1 (Intel 8M StrataFLASH)
+ * Base address = 0xD000_0000 - 0xD07F_FFFF
+ */
+
+#define FLASH_BASE1_PRELIM 0xD0000000
+#define CFG_OR1_PRELIM 0xFF800D42
+#define CFG_BR1_PRELIM 0xD0000801
+/* #define CFG_OR1 0xFF800D42 */
+/* #define CFG_BR1 0xD0000801 */
+
+
+/*
+ * BR2 and OR2 (SDRAM)
+ * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
+ * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
+ * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
+ *
+ */
+#define SDRAM_BASE 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+
+/* SDRAM timing */
+#define SDRAM_TIMING 0x00000A00
+
+/* For boards with 16M of SDRAM */
+#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
+#define CFG_16M_MBMR 0x18802114 /* Mem Periodic Timer Prescaler */
+
+/* For boards with 64M of SDRAM */
+#define SDRAM_64M_MAX_SIZE 0x04000000 /* max 64MB SDRAM */
+/* TODO - determine real value */
+#define CFG_64M_MBMR 0x18802114 /* Mem Period Timer Prescaler */
+
+#define CFG_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING)
+#define CFG_BR2 (SDRAM_BASE | 0x000000C1)
+
+
+/*
+ * BR3 and OR3 (NVRAM, Sipex, NAND Flash)
+ * Base address = 0xD100_0000 - 0xD100_FFFF (64K NVRAM)
+ * Base address = 0xD108_0000 - 0xD108_0000 (Sipex chip ctl register)
+ * Base address = 0xD110_0000 - 0xD110_0000 (NAND ctl register)
+ * Base address = 0xD138_0000 - 0xD138_0000 (LED ctl register)
+ *
+ */
+
+#define CFG_OR3_PRELIM 0xFFC00DF6
+#define CFG_BR3_PRELIM 0xD1000401
+/* #define CFG_OR3 0xFFC00DF6 */
+/* #define CFG_BR3 0xD1000401 */
+
+
+/*
+ * BR4 and OR4 (Unused)
+ * Base address = 0xE000_0000 - 0xE3FF_FFFF
+ *
+ */
+
+#define CFG_OR4_PRELIM 0xFF000000
+#define CFG_BR4_PRELIM 0xE0000000
+/* #define CFG_OR4 0xFF000000 */
+/* #define CFG_BR4 0xE0000000 */
+
+
+/*
+ * BR5 and OR5 (Expansion bus)
+ * Base address = 0xE400_0000 - 0xE7FF_FFFF
+ *
+ */
+
+#define CFG_OR5_PRELIM 0xFF000000
+#define CFG_BR5_PRELIM 0xE4000000
+/* #define CFG_OR5 0xFF000000 */
+/* #define CFG_BR5 0xE4000000 */
+
+
+
+/*
+ * BR6 and OR6 (Expansion bus)
+ * Base address = 0xE800_0000 - 0xEBFF_FFFF
+ *
+ */
+
+#define CFG_OR6_PRELIM 0xFF000000
+#define CFG_BR6_PRELIM 0xE8000000
+/* #define CFG_OR6 0xFF000000 */
+/* #define CFG_BR6 0xE8000000 */
+
+
+
+/*
+ * BR7 and OR7 (Expansion bus)
+ * Base address = 0xEC00_0000 - 0xEFFF_FFFF
+ *
+ */
+
+#define CFG_OR7_PRELIM 0xFF000000
+#define CFG_BR7_PRELIM 0xE8000000
+/* #define CFG_OR7 0xFF000000 */
+/* #define CFG_BR7 0xE8000000 */
+
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Sanity checks
+ */
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/flash.h b/include/flash.h
index e93b86e..32f4f4a 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -148,6 +148,9 @@
#define AMD_ID_LV160T 0x22C422C4 /* 29LV160T ID (16 M, top boot sector) */
#define AMD_ID_LV160B 0x22492249 /* 29LV160B ID (16 M, bottom boot sect) */
+#define AMD_ID_DL163T 0x22282228 /* 29DL163T ID (16 M, top boot sector) */
+#define AMD_ID_DL163B 0x222B222B /* 29DL163B ID (16 M, bottom boot sect) */
+
#define AMD_ID_LV320T 0x22F622F6 /* 29LV320T ID (32 M, top boot sector) */
#define AMD_ID_LV320B 0x22F922F9 /* 29LV320B ID (32 M, bottom boot sect) */
@@ -322,6 +325,8 @@
#define FLASH_AMLV128U 0x00A6 /* AMD 29LV128M ( 128M = 8M x 16 ) */
/* Intel 28F256L18T 256M = 128K x 255 + 32k x 4 */
#define FLASH_28F256L18T 0x00A8
+#define FLASH_AMDL163T 0x00A2 /* AMD AM29DL163T (2M x 16 ) */
+#define FLASH_AMDL163B 0x00A3
#define FLASH_UNKNOWN 0xFFFF /* unknown flash type */