diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 85ae7f6..007c728 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -409,6 +409,15 @@
 	  model. This should only be enabled for testing as it is not useful for
 	  anything else.
 
+config USB_HUB_USB251XB
+	tristate "USB251XB Hub Controller Configuration Driver"
+	depends on I2C
+	help
+	  This option enables support for configuration via SMBus of the
+	  Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration
+	  parameters may be set in devicetree or platform data.
+	  Say Y or M here if you need to configure such a device via SMBus.
+
 config TWL4030_LED
 	bool "Enable TWL4030 LED controller"
 	help
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 7a6047f..b9c54bd 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -20,6 +20,7 @@
 ifdef CONFIG_$(SPL_)DM_I2C
 ifndef CONFIG_SPL_BUILD
 obj-$(CONFIG_SANDBOX) += i2c_eeprom_emul.o
+obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
 endif
 endif
 ifdef CONFIG_SPL_OF_PLATDATA
diff --git a/drivers/misc/usb251xb.c b/drivers/misc/usb251xb.c
new file mode 100644
index 0000000..077edc2
--- /dev/null
+++ b/drivers/misc/usb251xb.c
@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for Microchip USB251xB USB 2.0 Hi-Speed Hub Controller
+ * Configuration via SMBus.
+ *
+ * Copyright (c) 2017 SKIDATA AG
+ *
+ * This work is based on the USB3503 driver by Dongjin Kim and
+ * a not-accepted patch by Fabien Lahoudere, see:
+ * https://patchwork.kernel.org/patch/9257715/
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <errno.h>
+#include <i2c.h>
+#include <linux/delay.h>
+#include <linux/utf.h>
+#include <power/regulator.h>
+
+/* Internal Register Set Addresses & Default Values acc. to DS00001692C */
+#define USB251XB_ADDR_VENDOR_ID_LSB	0x00
+#define USB251XB_ADDR_VENDOR_ID_MSB	0x01
+#define USB251XB_DEF_VENDOR_ID		0x0424
+
+#define USB251XB_ADDR_PRODUCT_ID_LSB	0x02
+#define USB251XB_ADDR_PRODUCT_ID_MSB	0x03
+
+#define USB251XB_ADDR_DEVICE_ID_LSB	0x04
+#define USB251XB_ADDR_DEVICE_ID_MSB	0x05
+#define USB251XB_DEF_DEVICE_ID		0x0BB3
+
+#define USB251XB_ADDR_CONFIG_DATA_1	0x06
+#define USB251XB_DEF_CONFIG_DATA_1	0x9B
+#define USB251XB_ADDR_CONFIG_DATA_2	0x07
+#define USB251XB_DEF_CONFIG_DATA_2	0x20
+#define USB251XB_ADDR_CONFIG_DATA_3	0x08
+#define USB251XB_DEF_CONFIG_DATA_3	0x02
+
+#define USB251XB_ADDR_NON_REMOVABLE_DEVICES	0x09
+#define USB251XB_DEF_NON_REMOVABLE_DEVICES	0x00
+
+#define USB251XB_ADDR_PORT_DISABLE_SELF	0x0A
+#define USB251XB_DEF_PORT_DISABLE_SELF	0x00
+#define USB251XB_ADDR_PORT_DISABLE_BUS	0x0B
+#define USB251XB_DEF_PORT_DISABLE_BUS	0x00
+
+#define USB251XB_ADDR_MAX_POWER_SELF	0x0C
+#define USB251XB_DEF_MAX_POWER_SELF	0x01
+#define USB251XB_ADDR_MAX_POWER_BUS	0x0D
+#define USB251XB_DEF_MAX_POWER_BUS	0x32
+
+#define USB251XB_ADDR_MAX_CURRENT_SELF	0x0E
+#define USB251XB_DEF_MAX_CURRENT_SELF	0x01
+#define USB251XB_ADDR_MAX_CURRENT_BUS	0x0F
+#define USB251XB_DEF_MAX_CURRENT_BUS	0x32
+
+#define USB251XB_ADDR_POWER_ON_TIME	0x10
+#define USB251XB_DEF_POWER_ON_TIME	0x32
+
+#define USB251XB_ADDR_LANGUAGE_ID_HIGH	0x11
+#define USB251XB_ADDR_LANGUAGE_ID_LOW	0x12
+#define USB251XB_DEF_LANGUAGE_ID	0x0000
+
+#define USB251XB_STRING_BUFSIZE			62
+#define USB251XB_ADDR_MANUFACTURER_STRING_LEN	0x13
+#define USB251XB_ADDR_MANUFACTURER_STRING	0x16
+#define USB251XB_DEF_MANUFACTURER_STRING	"Microchip"
+
+#define USB251XB_ADDR_PRODUCT_STRING_LEN	0x14
+#define USB251XB_ADDR_PRODUCT_STRING		0x54
+
+#define USB251XB_ADDR_SERIAL_STRING_LEN		0x15
+#define USB251XB_ADDR_SERIAL_STRING		0x92
+#define USB251XB_DEF_SERIAL_STRING		""
+
+#define USB251XB_ADDR_BATTERY_CHARGING_ENABLE	0xD0
+#define USB251XB_DEF_BATTERY_CHARGING_ENABLE	0x00
+
+#define USB251XB_ADDR_BOOST_UP	0xF6
+#define USB251XB_DEF_BOOST_UP	0x00
+#define USB251XB_ADDR_BOOST_57	0xF7
+#define USB251XB_DEF_BOOST_57	0x00
+#define USB251XB_ADDR_BOOST_14	0xF8
+#define USB251XB_DEF_BOOST_14	0x00
+
+#define USB251XB_ADDR_PORT_SWAP	0xFA
+#define USB251XB_DEF_PORT_SWAP	0x00
+
+#define USB251XB_ADDR_PORT_MAP_12	0xFB
+#define USB251XB_DEF_PORT_MAP_12	0x00
+#define USB251XB_ADDR_PORT_MAP_34	0xFC
+#define USB251XB_DEF_PORT_MAP_34	0x00 /* USB251{3B/i,4B/i,7/i} only */
+#define USB251XB_ADDR_PORT_MAP_56	0xFD
+#define USB251XB_DEF_PORT_MAP_56	0x00 /* USB2517/i only */
+#define USB251XB_ADDR_PORT_MAP_7	0xFE
+#define USB251XB_DEF_PORT_MAP_7		0x00 /* USB2517/i only */
+
+#define USB251XB_ADDR_STATUS_COMMAND		0xFF
+#define USB251XB_STATUS_COMMAND_SMBUS_DOWN	0x04
+#define USB251XB_STATUS_COMMAND_RESET		0x02
+#define USB251XB_STATUS_COMMAND_ATTACH		0x01
+
+#define USB251XB_I2C_REG_SZ	0x100
+#define USB251XB_I2C_WRITE_SZ	0x10
+
+#define DRIVER_NAME	"usb251xb"
+#define DRIVER_DESC	"Microchip USB 2.0 Hi-Speed Hub Controller"
+
+struct usb251xb {
+	struct device *dev;
+	struct i2c_client *i2c;
+	struct udevice *vdd;
+	u8 skip_config;
+	struct gpio_desc gpio_reset;
+	u32 vendor_id;
+	u32 product_id;
+	u32 device_id;
+	u8  conf_data1;
+	u8  conf_data2;
+	u8  conf_data3;
+	u8  non_rem_dev;
+	u8  port_disable_sp;
+	u8  port_disable_bp;
+	u8  max_power_sp;
+	u8  max_power_bp;
+	u8  max_current_sp;
+	u8  max_current_bp;
+	u8  power_on_time;
+	u32 lang_id;
+	u8 manufacturer_len;
+	u8 product_len;
+	u8 serial_len;
+	s16 manufacturer[USB251XB_STRING_BUFSIZE];
+	s16 product[USB251XB_STRING_BUFSIZE];
+	s16 serial[USB251XB_STRING_BUFSIZE];
+	u8  bat_charge_en;
+	u32 boost_up;
+	u8  boost_57;
+	u8  boost_14;
+	u8  port_swap;
+	u8  port_map12;
+	u8  port_map34;
+	u8  port_map56;
+	u8  port_map7;
+	u8  status;
+};
+
+struct usb251xb_data {
+	u16 product_id;
+	u8 port_cnt;
+	bool led_support;
+	bool bat_support;
+	char product_str[USB251XB_STRING_BUFSIZE / 2]; /* ASCII string */
+};
+
+static const struct usb251xb_data usb2422_data = {
+	.product_id = 0x2422,
+	.port_cnt = 2,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2422",
+};
+
+static const struct usb251xb_data usb2512b_data = {
+	.product_id = 0x2512,
+	.port_cnt = 2,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2512B",
+};
+
+static const struct usb251xb_data usb2512bi_data = {
+	.product_id = 0x2512,
+	.port_cnt = 2,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2512Bi",
+};
+
+static const struct usb251xb_data usb2513b_data = {
+	.product_id = 0x2513,
+	.port_cnt = 3,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2513B",
+};
+
+static const struct usb251xb_data usb2513bi_data = {
+	.product_id = 0x2513,
+	.port_cnt = 3,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2513Bi",
+};
+
+static const struct usb251xb_data usb2514b_data = {
+	.product_id = 0x2514,
+	.port_cnt = 4,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2514B",
+};
+
+static const struct usb251xb_data usb2514bi_data = {
+	.product_id = 0x2514,
+	.port_cnt = 4,
+	.led_support = false,
+	.bat_support = true,
+	.product_str = "USB2514Bi",
+};
+
+static const struct usb251xb_data usb2517_data = {
+	.product_id = 0x2517,
+	.port_cnt = 7,
+	.led_support = true,
+	.bat_support = false,
+	.product_str = "USB2517",
+};
+
+static const struct usb251xb_data usb2517i_data = {
+	.product_id = 0x2517,
+	.port_cnt = 7,
+	.led_support = true,
+	.bat_support = false,
+	.product_str = "USB2517i",
+};
+
+static void usb251xb_reset(struct usb251xb *hub)
+{
+	dm_gpio_set_value(&hub->gpio_reset, 1);
+	udelay(10);	/* >=1us RESET_N asserted */
+	dm_gpio_set_value(&hub->gpio_reset, 0);
+
+	/* wait for hub recovery/stabilization */
+	udelay(750);	/* >=500us after RESET_N deasserted */
+}
+
+static int usb251xb_connect(struct udevice *dev)
+{
+	struct usb251xb *hub = dev_get_priv(dev);
+	char i2c_wb[USB251XB_I2C_REG_SZ];
+	int err, i;
+
+	memset(i2c_wb, 0, USB251XB_I2C_REG_SZ);
+
+	if (hub->skip_config) {
+		dev_info(dev, "Skip hub configuration, only attach.\n");
+		i2c_wb[0] = 0x01;
+		i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH;
+
+		usb251xb_reset(hub);
+
+		err = dm_i2c_write(dev, USB251XB_ADDR_STATUS_COMMAND, i2c_wb, 2);
+		if (err) {
+			dev_err(dev, "attaching hub failed: %d\n", err);
+			return err;
+		}
+		return 0;
+	}
+
+	i2c_wb[USB251XB_ADDR_VENDOR_ID_MSB]     = (hub->vendor_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_VENDOR_ID_LSB]     = hub->vendor_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_PRODUCT_ID_MSB]    = (hub->product_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_PRODUCT_ID_LSB]    = hub->product_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_DEVICE_ID_MSB]     = (hub->device_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_DEVICE_ID_LSB]     = hub->device_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_1]     = hub->conf_data1;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_2]     = hub->conf_data2;
+	i2c_wb[USB251XB_ADDR_CONFIG_DATA_3]     = hub->conf_data3;
+	i2c_wb[USB251XB_ADDR_NON_REMOVABLE_DEVICES] = hub->non_rem_dev;
+	i2c_wb[USB251XB_ADDR_PORT_DISABLE_SELF] = hub->port_disable_sp;
+	i2c_wb[USB251XB_ADDR_PORT_DISABLE_BUS]  = hub->port_disable_bp;
+	i2c_wb[USB251XB_ADDR_MAX_POWER_SELF]    = hub->max_power_sp;
+	i2c_wb[USB251XB_ADDR_MAX_POWER_BUS]     = hub->max_power_bp;
+	i2c_wb[USB251XB_ADDR_MAX_CURRENT_SELF]  = hub->max_current_sp;
+	i2c_wb[USB251XB_ADDR_MAX_CURRENT_BUS]   = hub->max_current_bp;
+	i2c_wb[USB251XB_ADDR_POWER_ON_TIME]     = hub->power_on_time;
+	i2c_wb[USB251XB_ADDR_LANGUAGE_ID_HIGH]  = (hub->lang_id >> 8) & 0xFF;
+	i2c_wb[USB251XB_ADDR_LANGUAGE_ID_LOW]   = hub->lang_id & 0xFF;
+	i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING_LEN] = hub->manufacturer_len;
+	i2c_wb[USB251XB_ADDR_PRODUCT_STRING_LEN]      = hub->product_len;
+	i2c_wb[USB251XB_ADDR_SERIAL_STRING_LEN]       = hub->serial_len;
+	memcpy(&i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING], hub->manufacturer,
+	       USB251XB_STRING_BUFSIZE);
+	memcpy(&i2c_wb[USB251XB_ADDR_SERIAL_STRING], hub->serial,
+	       USB251XB_STRING_BUFSIZE);
+	memcpy(&i2c_wb[USB251XB_ADDR_PRODUCT_STRING], hub->product,
+	       USB251XB_STRING_BUFSIZE);
+	i2c_wb[USB251XB_ADDR_BATTERY_CHARGING_ENABLE] = hub->bat_charge_en;
+	i2c_wb[USB251XB_ADDR_BOOST_UP]          = hub->boost_up;
+	i2c_wb[USB251XB_ADDR_BOOST_57]          = hub->boost_57;
+	i2c_wb[USB251XB_ADDR_BOOST_14]          = hub->boost_14;
+	i2c_wb[USB251XB_ADDR_PORT_SWAP]         = hub->port_swap;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_12]       = hub->port_map12;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_34]       = hub->port_map34;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_56]       = hub->port_map56;
+	i2c_wb[USB251XB_ADDR_PORT_MAP_7]        = hub->port_map7;
+	i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH;
+
+	usb251xb_reset(hub);
+
+	/* write registers */
+	for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) {
+		int offset = i * USB251XB_I2C_WRITE_SZ;
+		char wbuf[USB251XB_I2C_WRITE_SZ + 1];
+
+		/* The first data byte transferred tells the hub how many data
+		 * bytes will follow (byte count).
+		 */
+		wbuf[0] = USB251XB_I2C_WRITE_SZ;
+		memcpy(&wbuf[1], &i2c_wb[offset], USB251XB_I2C_WRITE_SZ);
+
+		dev_dbg(dev, "writing %d byte block %d to 0x%02X\n",
+			USB251XB_I2C_WRITE_SZ, i, offset);
+
+		err = dm_i2c_write(dev, offset, wbuf, USB251XB_I2C_WRITE_SZ + 1);
+		if (err)
+			goto out_err;
+	}
+
+	dev_info(dev, "Hub configuration was successful.\n");
+	return 0;
+
+out_err:
+	dev_err(dev, "configuring block %d failed: %d\n", i, err);
+	return err;
+}
+
+static int usb251xb_probe(struct udevice *dev)
+{
+	struct usb251xb *hub = dev_get_priv(dev);
+	int err;
+
+	if (IS_ENABLED(CONFIG_DM_REGULATOR) && hub->vdd) {
+		err = regulator_set_enable(hub->vdd, true);
+		if (err)
+			return err;
+	}
+
+	err = usb251xb_connect(dev);
+	if (err) {
+		dev_err(dev, "Failed to connect hub (%d)\n", err);
+		return err;
+	}
+
+	dev_info(dev, "Hub probed successfully\n");
+
+	return 0;
+}
+
+static void usb251xb_get_ports_field(struct udevice *dev,
+				     const char *prop_name, u8 port_cnt,
+				     bool ds_only, u8 *fld)
+{
+	u32 i, port;
+	int ret;
+
+	for (i = 0; i < port_cnt; i++) {
+		ret = dev_read_u32_index(dev, prop_name, i, &port);
+		if (ret)
+			continue;
+		if (port >= ds_only ? 1 : 0 && port <= port_cnt)
+			*fld |= BIT(port);
+		else
+			dev_warn(dev, "port %u doesn't exist\n", port);
+	}
+}
+
+static int usb251xb_of_to_plat(struct udevice *dev)
+{
+	struct usb251xb_data *data =
+		(struct usb251xb_data *)dev_get_driver_data(dev);
+	struct usb251xb *hub = dev_get_priv(dev);
+	char str[USB251XB_STRING_BUFSIZE / 2];
+	const char *cproperty_char;
+	u32 property_u32 = 0;
+	int len, err;
+
+	if (dev_read_bool(dev, "skip-config"))
+		hub->skip_config = 1;
+	else
+		hub->skip_config = 0;
+
+	err = gpio_request_by_name(dev, "reset-gpios", 0, &hub->gpio_reset,
+				   GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+	if (err && err != -ENOENT) {
+		dev_err(dev, "unable to request GPIO reset pin (%d)\n", err);
+		return err;
+	}
+
+	if (IS_ENABLED(CONFIG_DM_REGULATOR)) {
+		err = device_get_supply_regulator(dev, "vdd-supply",
+						  &hub->vdd);
+		if (err && err != -ENOENT) {
+			dev_err(dev, "Warning: cannot get power supply\n");
+			return err;
+		}
+	}
+
+	if (dev_read_u32(dev, "vendor-id", &hub->vendor_id))
+		hub->vendor_id = USB251XB_DEF_VENDOR_ID;
+
+	if (dev_read_u32(dev, "product-id", &hub->product_id))
+		hub->product_id = data->product_id;
+
+	if (dev_read_u32(dev, "device-id", &hub->device_id))
+		hub->device_id = USB251XB_DEF_DEVICE_ID;
+
+	hub->conf_data1 = USB251XB_DEF_CONFIG_DATA_1;
+	if (dev_read_bool(dev, "self-powered")) {
+		hub->conf_data1 |= BIT(7);
+
+		/* Configure Over-Current sens when self-powered */
+		hub->conf_data1 &= ~BIT(2);
+		if (dev_read_bool(dev, "ganged-sensing"))
+			hub->conf_data1 &= ~BIT(1);
+		else if (dev_read_bool(dev, "individual-sensing"))
+			hub->conf_data1 |= BIT(1);
+	} else if (dev_read_bool(dev, "bus-powered")) {
+		hub->conf_data1 &= ~BIT(7);
+
+		/* Disable Over-Current sense when bus-powered */
+		hub->conf_data1 |= BIT(2);
+	}
+
+	if (dev_read_bool(dev, "disable-hi-speed"))
+		hub->conf_data1 |= BIT(5);
+
+	if (dev_read_bool(dev, "multi-tt"))
+		hub->conf_data1 |= BIT(4);
+	else if (dev_read_bool(dev, "single-tt"))
+		hub->conf_data1 &= ~BIT(4);
+
+	if (dev_read_bool(dev, "disable-eop"))
+		hub->conf_data1 |= BIT(3);
+
+	if (dev_read_bool(dev, "individual-port-switching"))
+		hub->conf_data1 |= BIT(0);
+	else if (dev_read_bool(dev, "ganged-port-switching"))
+		hub->conf_data1 &= ~BIT(0);
+
+	hub->conf_data2 = USB251XB_DEF_CONFIG_DATA_2;
+	if (dev_read_bool(dev, "dynamic-power-switching"))
+		hub->conf_data2 |= BIT(7);
+
+	if (!dev_read_u32(dev, "oc-delay-us", &property_u32)) {
+		if (property_u32 == 100) {
+			/* 100 us*/
+			hub->conf_data2 &= ~BIT(5);
+			hub->conf_data2 &= ~BIT(4);
+		} else if (property_u32 == 4000) {
+			/* 4 ms */
+			hub->conf_data2 &= ~BIT(5);
+			hub->conf_data2 |= BIT(4);
+		} else if (property_u32 == 16000) {
+			/* 16 ms */
+			hub->conf_data2 |= BIT(5);
+			hub->conf_data2 |= BIT(4);
+		} else {
+			/* 8 ms (DEFAULT) */
+			hub->conf_data2 |= BIT(5);
+			hub->conf_data2 &= ~BIT(4);
+		}
+	}
+
+	if (dev_read_bool(dev, "compound-device"))
+		hub->conf_data2 |= BIT(3);
+
+	hub->conf_data3 = USB251XB_DEF_CONFIG_DATA_3;
+	if (dev_read_bool(dev, "port-mapping-mode"))
+		hub->conf_data3 |= BIT(3);
+
+	if (data->led_support && dev_read_bool(dev, "led-usb-mode"))
+		hub->conf_data3 &= ~BIT(1);
+
+	if (dev_read_bool(dev, "string-support"))
+		hub->conf_data3 |= BIT(0);
+
+	hub->non_rem_dev = USB251XB_DEF_NON_REMOVABLE_DEVICES;
+	usb251xb_get_ports_field(dev, "non-removable-ports", data->port_cnt,
+				 true, &hub->non_rem_dev);
+
+	hub->port_disable_sp = USB251XB_DEF_PORT_DISABLE_SELF;
+	usb251xb_get_ports_field(dev, "sp-disabled-ports", data->port_cnt,
+				 true, &hub->port_disable_sp);
+
+	hub->port_disable_bp = USB251XB_DEF_PORT_DISABLE_BUS;
+	usb251xb_get_ports_field(dev, "bp-disabled-ports", data->port_cnt,
+				 true, &hub->port_disable_bp);
+
+	hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF;
+	if (!dev_read_u32(dev, "sp-max-total-current-microamp", &property_u32))
+		hub->max_power_sp = min_t(u8, property_u32 / 2000, 50);
+
+	hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS;
+	if (!dev_read_u32(dev, "bp-max-total-current-microamp", &property_u32))
+		hub->max_power_bp = min_t(u8, property_u32 / 2000, 255);
+
+	hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF;
+	if (!dev_read_u32(dev, "sp-max-removable-current-microamp",
+			  &property_u32))
+		hub->max_current_sp = min_t(u8, property_u32 / 2000, 50);
+
+	hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS;
+	if (!dev_read_u32(dev, "bp-max-removable-current-microamp",
+			  &property_u32))
+		hub->max_current_bp = min_t(u8, property_u32 / 2000, 255);
+
+	hub->power_on_time = USB251XB_DEF_POWER_ON_TIME;
+	if (!dev_read_u32(dev, "power-on-time-ms", &property_u32))
+		hub->power_on_time = min_t(u8, property_u32 / 2, 255);
+
+	if (dev_read_u32(dev, "language-id", &hub->lang_id))
+		hub->lang_id = USB251XB_DEF_LANGUAGE_ID;
+
+	if (!dev_read_u32(dev, "boost-up", &hub->boost_up))
+		hub->boost_up = USB251XB_DEF_BOOST_UP;
+
+	cproperty_char = dev_read_string(dev, "manufacturer");
+	strlcpy(str, cproperty_char ? : USB251XB_DEF_MANUFACTURER_STRING,
+		sizeof(str));
+	hub->manufacturer_len = strlen(str) & 0xFF;
+	memset(hub->manufacturer, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8_to_utf16le(str, hub->manufacturer, len);
+
+	cproperty_char = dev_read_string(dev, "product");
+	strlcpy(str, cproperty_char ? : data->product_str, sizeof(str));
+	hub->product_len = strlen(str) & 0xFF;
+	memset(hub->product, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8_to_utf16le(str, hub->product, len);
+
+	cproperty_char = dev_read_string(dev, "serial");
+	strlcpy(str, cproperty_char ? : USB251XB_DEF_SERIAL_STRING,
+		sizeof(str));
+	hub->serial_len = strlen(str) & 0xFF;
+	memset(hub->serial, 0, USB251XB_STRING_BUFSIZE);
+	len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+	len = utf8_to_utf16le(str, hub->serial, len);
+
+	/*
+	 * The datasheet documents the register as 'Port Swap' but in real the
+	 * register controls the USB DP/DM signal swapping for each port.
+	 */
+	hub->port_swap = USB251XB_DEF_PORT_SWAP;
+	usb251xb_get_ports_field(dev, "swap-dx-lanes", data->port_cnt,
+				 false, &hub->port_swap);
+
+	/* The following parameters are currently not exposed to devicetree, but
+	 * may be as soon as needed.
+	 */
+	hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE;
+	hub->boost_57 = USB251XB_DEF_BOOST_57;
+	hub->boost_14 = USB251XB_DEF_BOOST_14;
+	hub->port_map12 = USB251XB_DEF_PORT_MAP_12;
+	hub->port_map34 = USB251XB_DEF_PORT_MAP_34;
+	hub->port_map56 = USB251XB_DEF_PORT_MAP_56;
+	hub->port_map7  = USB251XB_DEF_PORT_MAP_7;
+
+	return 0;
+}
+
+static const struct udevice_id usb251xb_of_match[] = {
+	{
+		.compatible = "microchip,usb2422",
+		.data = (ulong)&usb2422_data,
+	}, {
+		.compatible = "microchip,usb2512b",
+		.data = (ulong)&usb2512b_data,
+	}, {
+		.compatible = "microchip,usb2512bi",
+		.data = (ulong)&usb2512bi_data,
+	}, {
+		.compatible = "microchip,usb2513b",
+		.data = (ulong)&usb2513b_data,
+	}, {
+		.compatible = "microchip,usb2513bi",
+		.data = (ulong)&usb2513bi_data,
+	}, {
+		.compatible = "microchip,usb2514b",
+		.data = (ulong)&usb2514b_data,
+	}, {
+		.compatible = "microchip,usb2514bi",
+		.data = (ulong)&usb2514bi_data,
+	}, {
+		.compatible = "microchip,usb2517",
+		.data = (ulong)&usb2517_data,
+	}, {
+		.compatible = "microchip,usb2517i",
+		.data = (ulong)&usb2517i_data,
+	}
+};
+
+U_BOOT_DRIVER(usb251xb) = {
+	.name		= "usb251xb",
+	.id		= UCLASS_MISC,
+	.of_match	= usb251xb_of_match,
+	.of_to_plat	= usb251xb_of_to_plat,
+	.probe		= usb251xb_probe,
+	.priv_auto	= sizeof(struct usb251xb),
+};