fpga: zynq: Add support for loading bitstream
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index b48f623..0b51dcd 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -30,6 +30,7 @@
COBJS-$(CONFIG_FPGA_SPARTAN2) += spartan2.o
COBJS-$(CONFIG_FPGA_SPARTAN3) += spartan3.o
COBJS-$(CONFIG_FPGA_VIRTEX2) += virtex2.o
+COBJS-$(CONFIG_FPGA_ZYNQPL) += zynqpl.o
COBJS-$(CONFIG_FPGA_XILINX) += xilinx.o
COBJS-$(CONFIG_FPGA_LATTICE) += ivm_core.o lattice.o
ifdef CONFIG_FPGA_ALTERA
diff --git a/drivers/fpga/xilinx.c b/drivers/fpga/xilinx.c
index df5f9bf..496aa2f 100644
--- a/drivers/fpga/xilinx.c
+++ b/drivers/fpga/xilinx.c
@@ -1,4 +1,6 @@
/*
+ * (C) Copyright 2012-2013, Xilinx, Michal Simek
+ *
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com
@@ -31,6 +33,7 @@
#include <virtex2.h>
#include <spartan2.h>
#include <spartan3.h>
+#include <zynqpl.h>
#if 0
#define FPGA_DEBUG
@@ -172,6 +175,16 @@
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ PRINTF("%s: Launching the Zynq PL Loader...\n",
+ __func__);
+ ret_val = zynq_load(desc, buf, bsize);
+#else
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
+ break;
default:
printf ("%s: Unsupported family type, %d\n",
@@ -219,6 +232,16 @@
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ PRINTF("%s: Launching the Zynq PL Reader...\n",
+ __func__);
+ ret_val = zynq_dump(desc, buf, bsize);
+#else
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
+ break;
default:
printf ("%s: Unsupported family type, %d\n",
@@ -244,6 +267,9 @@
case Xilinx_Virtex2:
printf ("Virtex-II\n");
break;
+ case xilinx_zynq:
+ printf("Zynq PL\n");
+ break;
/* Add new family types here */
default:
printf ("Unknown family type, %d\n", desc->family);
@@ -269,6 +295,9 @@
case master_selectmap:
printf ("Master SelectMap Mode\n");
break;
+ case devcfg:
+ printf("Device configuration interface (Zynq)\n");
+ break;
/* Add new interface types here */
default:
printf ("Unsupported interface type, %d\n", desc->iface);
@@ -308,6 +337,14 @@
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ zynq_info(desc);
+#else
+ /* just in case */
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
/* Add new family types here */
default:
/* we don't need a message here - we give one up above */
diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
new file mode 100644
index 0000000..8feccde
--- /dev/null
+++ b/drivers/fpga/zynqpl.c
@@ -0,0 +1,355 @@
+/*
+ * (C) Copyright 2012-2013, Xilinx, Michal Simek
+ *
+ * (C) Copyright 2012
+ * Joe Hershberger <joe.hershberger@ni.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <zynqpl.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+
+#define DEVCFG_CTRL_PCFG_PROG_B 0x40000000
+#define DEVCFG_ISR_FATAL_ERROR_MASK 0x00740040
+#define DEVCFG_ISR_ERROR_FLAGS_MASK 0x00340840
+#define DEVCFG_ISR_RX_FIFO_OV 0x00040000
+#define DEVCFG_ISR_DMA_DONE 0x00002000
+#define DEVCFG_ISR_PCFG_DONE 0x00000004
+#define DEVCFG_STATUS_DMA_CMD_Q_F 0x80000000
+#define DEVCFG_STATUS_DMA_CMD_Q_E 0x40000000
+#define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000
+#define DEVCFG_STATUS_PCFG_INIT 0x00000010
+#define DEVCFG_MCTRL_RFIFO_FLUSH 0x00000002
+#define DEVCFG_MCTRL_WFIFO_FLUSH 0x00000001
+
+#ifndef CONFIG_SYS_FPGA_WAIT
+#define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */
+#endif
+
+#ifndef CONFIG_SYS_FPGA_PROG_TIME
+#define CONFIG_SYS_FPGA_PROG_TIME CONFIG_SYS_HZ /* 1 s */
+#endif
+
+int zynq_info(Xilinx_desc *desc)
+{
+ return FPGA_SUCCESS;
+}
+
+#define DUMMY_WORD 0xffffffff
+
+/* Xilinx binary format header */
+static const u32 bin_format[] = {
+ DUMMY_WORD, /* Dummy words */
+ DUMMY_WORD,
+ DUMMY_WORD,
+ DUMMY_WORD,
+ DUMMY_WORD,
+ DUMMY_WORD,
+ DUMMY_WORD,
+ DUMMY_WORD,
+ 0x000000bb, /* Sync word */
+ 0x11220044, /* Sync word */
+ DUMMY_WORD,
+ DUMMY_WORD,
+ 0xaa995566, /* Sync word */
+};
+
+#define SWAP_NO 1
+#define SWAP_DONE 2
+
+/*
+ * Load the whole word from unaligned buffer
+ * Keep in your mind that it is byte loading on little-endian system
+ */
+static u32 load_word(const void *buf, u32 swap)
+{
+ u32 word = 0;
+ u8 *bitc = (u8 *)buf;
+ int p;
+
+ if (swap == SWAP_NO) {
+ for (p = 0; p < 4; p++) {
+ word <<= 8;
+ word |= bitc[p];
+ }
+ } else {
+ for (p = 3; p >= 0; p--) {
+ word <<= 8;
+ word |= bitc[p];
+ }
+ }
+
+ return word;
+}
+
+static u32 check_header(const void *buf)
+{
+ u32 i, pattern;
+ int swap = SWAP_NO;
+ u32 *test = (u32 *)buf;
+
+ debug("%s: Let's check bitstream header\n", __func__);
+
+ /* Checking that passing bin is not a bitstream */
+ for (i = 0; i < ARRAY_SIZE(bin_format); i++) {
+ pattern = load_word(&test[i], swap);
+
+ /*
+ * Bitstreams in binary format are swapped
+ * compare to regular bistream.
+ * Do not swap dummy word but if swap is done assume
+ * that parsing buffer is binary format
+ */
+ if ((__swab32(pattern) != DUMMY_WORD) &&
+ (__swab32(pattern) == bin_format[i])) {
+ pattern = __swab32(pattern);
+ swap = SWAP_DONE;
+ debug("%s: data swapped - let's swap\n", __func__);
+ }
+
+ debug("%s: %d/%x: pattern %x/%x bin_format\n", __func__, i,
+ (u32)&test[i], pattern, bin_format[i]);
+ if (pattern != bin_format[i]) {
+ debug("%s: Bitstream is not recognized\n", __func__);
+ return 0;
+ }
+ }
+ debug("%s: Found bitstream header at %x %s swapinng\n", __func__,
+ (u32)buf, swap == SWAP_NO ? "without" : "with");
+
+ return swap;
+}
+
+static void *check_data(u8 *buf, size_t bsize, u32 *swap)
+{
+ u32 word, p = 0; /* possition */
+
+ /* Because buf doesn't need to be aligned let's read it by chars */
+ for (p = 0; p < bsize; p++) {
+ word = load_word(&buf[p], SWAP_NO);
+ debug("%s: word %x %x/%x\n", __func__, word, p, (u32)&buf[p]);
+
+ /* Find the first bitstream dummy word */
+ if (word == DUMMY_WORD) {
+ debug("%s: Found dummy word at position %x/%x\n",
+ __func__, p, (u32)&buf[p]);
+ *swap = check_header(&buf[p]);
+ if (*swap) {
+ /* FIXME add full bitstream checking here */
+ return &buf[p];
+ }
+ }
+ /* Loop can be huge - support CTRL + C */
+ if (ctrlc())
+ return 0;
+ }
+ return 0;
+}
+
+
+int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+{
+ unsigned long ts; /* Timestamp */
+ u32 partialbit = 0;
+ u32 i, control, isr_status, status, swap, diff;
+ u32 *buf_start;
+
+ /* Detect if we are going working with partial or full bitstream */
+ if (bsize != desc->size) {
+ printf("%s: Working with partial bitstream\n", __func__);
+ partialbit = 1;
+ }
+
+ buf_start = check_data((u8 *)buf, bsize, &swap);
+ if (!buf_start)
+ return FPGA_FAIL;
+
+ /* Check if data is postpone from start */
+ diff = (u32)buf_start - (u32)buf;
+ if (diff) {
+ printf("%s: Bitstream is not validated yet (diff %x)\n",
+ __func__, diff);
+ return FPGA_FAIL;
+ }
+
+ if ((u32)buf_start & 0x3) {
+ u32 *new_buf = (u32 *)((u32)buf & ~0x3);
+
+ printf("%s: Align buffer at %x to %x(swap %d)\n", __func__,
+ (u32)buf_start, (u32)new_buf, swap);
+
+ for (i = 0; i < (bsize/4); i++)
+ new_buf[i] = load_word(&buf_start[i], swap);
+
+ swap = SWAP_DONE;
+ buf = new_buf;
+ } else if (swap != SWAP_DONE) {
+ /* For bitstream which are aligned */
+ u32 *new_buf = (u32 *)buf;
+
+ printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__,
+ swap);
+
+ for (i = 0; i < (bsize/4); i++)
+ new_buf[i] = load_word(&buf_start[i], swap);
+
+ swap = SWAP_DONE;
+ }
+
+ if (!partialbit) {
+ zynq_slcr_devcfg_disable();
+
+ /* Setting PCFG_PROG_B signal to high */
+ control = readl(&devcfg_base->ctrl);
+ writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+ /* Setting PCFG_PROG_B signal to low */
+ writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+
+ /* Polling the PCAP_INIT status for Reset */
+ ts = get_timer(0);
+ while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ printf("%s: Timeout wait for INIT to clear\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ }
+
+ /* Setting PCFG_PROG_B signal to high */
+ writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+
+ /* Polling the PCAP_INIT status for Set */
+ ts = get_timer(0);
+ while (!(readl(&devcfg_base->status) &
+ DEVCFG_STATUS_PCFG_INIT)) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ printf("%s: Timeout wait for INIT to set\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ }
+ }
+
+ isr_status = readl(&devcfg_base->int_sts);
+
+ /* Clear it all, so if Boot ROM comes back, it can proceed */
+ writel(0xFFFFFFFF, &devcfg_base->int_sts);
+
+ if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) {
+ debug("%s: Fatal errors in PCAP 0x%X\n", __func__, isr_status);
+
+ /* If RX FIFO overflow, need to flush RX FIFO first */
+ if (isr_status & DEVCFG_ISR_RX_FIFO_OV) {
+ writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl);
+ writel(0xFFFFFFFF, &devcfg_base->int_sts);
+ }
+ return FPGA_FAIL;
+ }
+
+ status = readl(&devcfg_base->status);
+
+ debug("%s: Status = 0x%08X\n", __func__, status);
+
+ if (status & DEVCFG_STATUS_DMA_CMD_Q_F) {
+ debug("%s: Error: device busy\n", __func__);
+ return FPGA_FAIL;
+ }
+
+ debug("%s: Device ready\n", __func__);
+
+ if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) {
+ if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) {
+ /* Error state, transfer cannot occur */
+ debug("%s: ISR indicates error\n", __func__);
+ return FPGA_FAIL;
+ } else {
+ /* Clear out the status */
+ writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
+ }
+ }
+
+ if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) {
+ /* Clear the count of completed DMA transfers */
+ writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status);
+ }
+
+ debug("%s: Source = 0x%08X\n", __func__, (u32)buf);
+ debug("%s: Size = %zu\n", __func__, bsize);
+
+ /* Set up the transfer */
+ writel((u32)buf | 1, &devcfg_base->dma_src_addr);
+ writel(0xFFFFFFFF, &devcfg_base->dma_dst_addr);
+ writel(bsize >> 2, &devcfg_base->dma_src_len);
+ writel(0, &devcfg_base->dma_dst_len);
+
+ isr_status = readl(&devcfg_base->int_sts);
+
+ /* Polling the PCAP_INIT status for Set */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
+ if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
+ debug("%s: Error: isr = 0x%08X\n", __func__,
+ isr_status);
+ debug("%s: Write count = 0x%08X\n", __func__,
+ readl(&devcfg_base->write_count));
+ debug("%s: Read count = 0x%08X\n", __func__,
+ readl(&devcfg_base->read_count));
+
+ return FPGA_FAIL;
+ }
+ if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
+ printf("%s: Timeout wait for DMA to complete\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
+
+ debug("%s: DMA transfer is done\n", __func__);
+
+ /* Check FPGA configuration completion */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ printf("%s: Timeout wait for FPGA to config\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
+
+ debug("%s: FPGA config done\n", __func__);
+
+ /* Clear out the DMA status */
+ writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
+
+ if (!partialbit)
+ zynq_slcr_devcfg_enable();
+
+ return FPGA_SUCCESS;
+}
+
+int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+{
+ return FPGA_FAIL;
+}