[FIX] Change configuration for XUPV2P Microblaze board
diff --git a/include/configs/xupv2p.h b/include/configs/xupv2p.h
index b4c720d..25fa495 100644
--- a/include/configs/xupv2p.h
+++ b/include/configs/xupv2p.h
@@ -31,13 +31,33 @@
#define CONFIG_XUPV2P 1
/* uart */
-#define CONFIG_SERIAL_BASE XILINX_UART_BASEADDR
-#define CONFIG_BAUDRATE XILINX_UART_BAUDRATE
+#ifdef XILINX_UARTLITE_BASEADDR
+#define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR
+#define CONFIG_BAUDRATE XILINX_UARTLITE_BAUDRATE
#define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE }
+#else
+#ifdef XILINX_UART16550_BASEADDR
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 4
+#define CONFIG_CONS_INDEX 1
+#define CFG_NS16550_COM1 XILINX_UART16550_BASEADDR
+#define CFG_NS16550_CLK XILINX_UART16550_CLOCK_HZ
+
+#define CONFIG_BAUDRATE 115200
+#define CFG_BAUDRATE_TABLE { 9600, 115200 }
+#endif
+#endif
/* ethernet */
-#define CONFIG_EMAC 1
-#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES
+#ifdef XILINX_EMAC_BASEADDR
+#define XILINX_EMAC 1
+#else
+#ifdef XILINX_EMACLITE_BASEADDR
+#define XILINX_EMACLITE 1
+#endif
+#endif
+#undef ET_DEBUG
/*
* setting reset address
@@ -48,11 +68,13 @@
* U-BOOT auto-relocate to TEXT_BASE. After RESET command Microblaze
* jump to CFG_RESET_ADDRESS where is the original U-BOOT code.
*/
-#define CFG_RESET_ADDRESS 0x36000000
+/* #define CFG_RESET_ADDRESS 0x36000000 */
/* gpio */
+#ifdef XILINX_GPIO_BASEADDR
#define CFG_GPIO_0 1
#define CFG_GPIO_0_ADDR XILINX_GPIO_BASEADDR
+#endif
/* interrupt controller */
#define CFG_INTC_0 1
@@ -118,6 +140,25 @@
#define CFG_ENV_IS_NOWHERE 1
#define CFG_ENV_SIZE 0x1000
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+#ifndef XILINX_SYSACE_BASEADDR
+#define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
+ CFG_CMD_MEMORY |\
+ CFG_CMD_IRQ |\
+ CFG_CMD_BDI |\
+ CFG_CMD_NET |\
+ CFG_CMD_IMI |\
+ CFG_CMD_ECHO |\
+ CFG_CMD_CACHE |\
+ CFG_CMD_RUN |\
+ CFG_CMD_AUTOSCRIPT |\
+ CFG_CMD_ASKENV |\
+ CFG_CMD_LOADS |\
+ CFG_CMD_LOADB |\
+ CFG_CMD_MISC |\
+ CFG_CMD_MFSL |\
+ CFG_CMD_PING \
+ )
+#else
#define CONFIG_COMMANDS (CONFIG__CMD_DFL |\
CFG_CMD_MEMORY |\
CFG_CMD_IRQ |\
@@ -134,8 +175,10 @@
CFG_CMD_MISC |\
CFG_CMD_FAT |\
CFG_CMD_EXT2 |\
+ CFG_CMD_MFSL |\
CFG_CMD_PING \
)
+#endif
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -150,7 +193,7 @@
#define CONFIG_BOOTDELAY 30
#define CONFIG_BOOTARGS "root=romfs"
-#define CONFIG_HOSTNAME "ml401"
+#define CONFIG_HOSTNAME "xupv2p"
#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
#define CONFIG_IPADDR 192.168.0.3
#define CONFIG_SERVERIP 192.168.0.5
@@ -166,11 +209,13 @@
"echo"
/* system ace */
+#ifdef XILINX_SYSACE_BASEADDR
#define CONFIG_SYSTEMACE
/* #define DEBUG_SYSTEMACE */
#define SYSTEMACE_CONFIG_FPGA
#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
#define CONFIG_DOS_PARTITION
+#endif
#endif /* __CONFIG_H */