drivers/net/phy/cortina.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Cortina CS4315/CS4340 10G PHY drivers
  *
  * Copyright 2014 Freescale Semiconductor, Inc.
  * Copyright 2018 NXP
  *
  */

 #include <config.h>
 #include <common.h>
 #include <malloc.h>
 #include <linux/ctype.h>
 #include <linux/string.h>
 #include <linux/err.h>
 #include <phy.h>
 #include <cortina.h>
 #ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
 #include <nand.h>
 #elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
 #include <spi_flash.h>
 #elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
 #include <mmc.h>
 #endif

 #ifndef CONFIG_PHYLIB_10G
 #error The Cortina PHY needs 10G support
 #endif

 #ifndef CORTINA_NO_FW_UPLOAD
 struct cortina_reg_config cortina_reg_cfg[] = {
 	/* CS4315_enable_sr_mode */
 	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
 	{VILLA_MSEQ_OPTIONS, 0xf},
 	{VILLA_MSEQ_PC, 0x0},
 	{VILLA_MSEQ_BANKSELECT,	   0x4},
 	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
 	{VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
 	{VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
 	{VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
 	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
 	{VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
 	{VILLA_MSEQ_ENABLE_MSB, 0x0000},
 	{VILLA_MSEQ_SPARE21_LSB, 0x6},
 	{VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
 	{VILLA_MSEQ_SPARE12_MSB, 0x0000},
 	/*
 	 * to invert the receiver path, uncomment the next line
 	 * write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
 	 *
 	 * SPARE2_LSB is used to configure the device while in sr mode to
 	 * enable power savings and to use the optical module LOS signal.
 	 * in power savings mode, the internal prbs checker can not be used.
 	 * if the optical module LOS signal is used as an input to the micro
 	 * code, then the micro code will wait until the optical module
 	 * LOS = 0 before turning on the adaptive equalizer.
 	 * Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
 	 * while setting bit 0 to 0 disables power savings mode.
 	 * Setting SPARE2_LSB bit 2 to 0 configures the device to use the
 	 * optical module LOS signal while setting bit 2 to 1 configures the
 	 * device so that it will ignore the optical module LOS SPARE2_LSB = 0
 	 */

 	/* enable power savings, ignore optical module LOS */
 	{VILLA_MSEQ_SPARE2_LSB, 0x5},

 	{VILLA_MSEQ_SPARE7_LSB, 0x1e},
 	{VILLA_MSEQ_BANKSELECT, 0x4},
 	{VILLA_MSEQ_SPARE9_LSB, 0x2},
 	{VILLA_MSEQ_SPARE3_LSB, 0x0F53},
 	{VILLA_MSEQ_SPARE3_MSB, 0x2006},
 	{VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
 	{VILLA_MSEQ_SPARE8_MSB, 0x0A46},
 	{VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
 	{VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
 	{VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
 	{VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
 	{VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
 	{VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
 	{VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
 	{VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
 	{VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
 	{VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
 	{VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
 	{VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
 	{VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
 	{VILLA_MSEQ_CAL_RX_SLICER, 0x80},
 	{VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
 	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
 	{VILLA_MSEQ_OPTIONS, 0x7},

 	/* set up min value for ffe1 */
 	{VILLA_MSEQ_COEF_INIT_SEL, 0x2},
 	{VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},

 	/* CS4315_sr_rx_pre_eq_set_4in */
 	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
 	{VILLA_MSEQ_OPTIONS, 0xf},
 	{VILLA_MSEQ_BANKSELECT, 0x4},
 	{VILLA_MSEQ_PC, 0x0},

 	/* for lengths from 3.5 to 4.5inches */
 	{VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
 	{VILLA_MSEQ_SPARE25_LSB, 0x0306},
 	{VILLA_MSEQ_SPARE21_LSB, 0x2},
 	{VILLA_MSEQ_SPARE23_LSB, 0x2},
 	{VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},

 	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
 	{VILLA_MSEQ_OPTIONS, 0x7},

 	/* CS4315_rx_drive_4inch */
 	/* for length  4inches */
 	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
 	{VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
 	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},

 	/* CS4315_tx_drive_4inch */
 	/* for length  4inches */
 	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
 	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
 	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
 };

 void cs4340_upload_firmware(struct phy_device *phydev)
 {
 	char line_temp[0x50] = {0};
 	char reg_addr[0x50] = {0};
 	char reg_data[0x50] = {0};
 	int i, line_cnt = 0, column_cnt = 0;
 	struct cortina_reg_config fw_temp;
 	char *addr = NULL;

 #if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) || \
 	defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)

 	addr = (char *)CONFIG_CORTINA_FW_ADDR;
 #elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
 	int ret;
 	size_t fw_length = CONFIG_CORTINA_FW_LENGTH;

 	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
 	ret = nand_read(get_nand_dev_by_index(0),
 			(loff_t)CONFIG_CORTINA_FW_ADDR,
 			&fw_length, (u_char *)addr);
 	if (ret == -EUCLEAN) {
 		printf("NAND read of Cortina firmware at 0x%x failed %d\n",
 		       CONFIG_CORTINA_FW_ADDR, ret);
 	}
 #elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
 	int ret;
 	struct spi_flash *ucode_flash;

 	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
 	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
 				CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
 	if (!ucode_flash) {
 		puts("SF: probe for Cortina ucode failed\n");
 	} else {
 		ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
 				     CONFIG_CORTINA_FW_LENGTH, addr);
 		if (ret)
 			puts("SF: read for Cortina ucode failed\n");
 		spi_flash_free(ucode_flash);
 	}
 #elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
 	int dev = CONFIG_SYS_MMC_ENV_DEV;
 	u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
 	u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
 	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);

 	if (!mmc) {
 		puts("Failed to find MMC device for Cortina ucode\n");
 	} else {
 		addr = malloc(CONFIG_CORTINA_FW_LENGTH);
 		printf("MMC read: dev # %u, block # %u, count %u ...\n",
 		       dev, blk, cnt);
 		mmc_init(mmc);
 		(void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt,
 						addr);
 	}
 #endif

 	while (*addr != 'Q') {
 		i = 0;

 		while (*addr != 0x0a) {
 			line_temp[i++] = *addr++;
 			if (0x50 < i) {
 				printf("Not found Cortina PHY ucode at 0x%p\n",
 				       (char *)CONFIG_CORTINA_FW_ADDR);
 				return;
 			}
 		}

 		addr++;  /* skip '\n' */
 		line_cnt++;
 		column_cnt = i;
 		line_temp[column_cnt] = '\0';

 		if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
 			return;

 		for (i = 0; i < column_cnt; i++) {
 			if (isspace(line_temp[i++]))
 				break;
 		}

 		memcpy(reg_addr, line_temp, i);
 		memcpy(reg_data, &line_temp[i], column_cnt - i);
 		strim(reg_addr);
 		strim(reg_data);
 		fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
 		fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
 				     0xffff;
 		phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
 	}
 }
 #endif

 int cs4340_phy_init(struct phy_device *phydev)
 {
 #ifndef CORTINA_NO_FW_UPLOAD
 	int timeout = 100;  /* 100ms */
 #endif
 	int reg_value;

 	/*
 	 * Cortina phy has provision to store
 	 * phy firmware in attached dedicated EEPROM.
 	 * Boards designed with EEPROM attached to Cortina
 	 * does not require FW upload.
 	 */
 #ifndef CORTINA_NO_FW_UPLOAD
 	/* step1: BIST test */
 	phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL,     0x0004);
 	phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
 	phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL,    0x0001);
 	while (--timeout) {
 		reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
 		if (reg_value & mseq_edc_bist_done) {
 			if (0 == (reg_value & mseq_edc_bist_fail))
 				break;
 		}
 		udelay(1000);
 	}

 	if (!timeout) {
 		printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
 		return -1;
 	}

 	/* setp2: upload ucode */
 	cs4340_upload_firmware(phydev);
 #endif
 	reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
 	if (reg_value) {
 		debug("%s checksum status failed.\n", __func__);
 		return -1;
 	}

 	return 0;
 }

 int cs4340_config(struct phy_device *phydev)
 {
 	cs4340_phy_init(phydev);
 	return 0;
 }

 int cs4340_probe(struct phy_device *phydev)
 {
 	phydev->flags = PHY_FLAG_BROKEN_RESET;
 	return 0;
 }

 int cs4340_startup(struct phy_device *phydev)
 {
 	phydev->link = 1;

 	/* For now just lie and say it's 10G all the time */
 	phydev->speed = SPEED_10000;
 	phydev->duplex = DUPLEX_FULL;
 	return 0;
 }

 struct phy_driver cs4340_driver = {
 	.name = "Cortina CS4315/CS4340",
 	.uid = PHY_UID_CS4340,
 	.mask = 0xfffffff0,
 	.features = PHY_10G_FEATURES,
 	.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
 		 MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
 		 MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
 	.config = &cs4340_config,
 	.probe	= &cs4340_probe,
 	.startup = &cs4340_startup,
 	.shutdown = &gen10g_shutdown,
 };

 int phy_cortina_init(void)
 {
 	phy_register(&cs4340_driver);
 	return 0;
 }

 int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
 {
 	int phy_reg;

 	/* Cortina PHY has non-standard offset of PHY ID registers */
 	phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
 	if (phy_reg < 0)
 		return -EIO;
 	*phy_id = (phy_reg & 0xffff) << 16;

 	phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
 	if (phy_reg < 0)
 		return -EIO;
 	*phy_id |= (phy_reg & 0xffff);

 	if (*phy_id == PHY_UID_CS4340)
 		return 0;

 	/*
 	 * If Cortina PHY not detected,
 	 * try generic way to find PHY ID registers
 	 */
 	phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
 	if (phy_reg < 0)
 		return -EIO;
 	*phy_id = (phy_reg & 0xffff) << 16;

 	phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
 	if (phy_reg < 0)
 		return -EIO;
 	*phy_id |= (phy_reg & 0xffff);

 	return 0;
 }
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* Cortina CS4315/CS4340 10G PHY drivers
	*
	* Copyright 2014 Freescale Semiconductor, Inc.
	* Copyright 2018 NXP
	*
	*/

	#include <config.h>
	#include <common.h>
	#include <malloc.h>
	#include <linux/ctype.h>
	#include <linux/string.h>
	#include <linux/err.h>
	#include <phy.h>
	#include <cortina.h>
	#ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
	#include <nand.h>
	#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
	#include <spi_flash.h>
	#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
	#include <mmc.h>
	#endif

	#ifndef CONFIG_PHYLIB_10G
	#error The Cortina PHY needs 10G support
	#endif

	#ifndef CORTINA_NO_FW_UPLOAD
	struct cortina_reg_config cortina_reg_cfg[] = {
	/* CS4315_enable_sr_mode */
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
	{VILLA_MSEQ_OPTIONS, 0xf},
	{VILLA_MSEQ_PC, 0x0},
	{VILLA_MSEQ_BANKSELECT, 0x4},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
	{VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
	{VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
	{VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
	{VILLA_MSEQ_ENABLE_MSB, 0x0000},
	{VILLA_MSEQ_SPARE21_LSB, 0x6},
	{VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
	{VILLA_MSEQ_SPARE12_MSB, 0x0000},
	/*
	* to invert the receiver path, uncomment the next line
	* write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
	*
	* SPARE2_LSB is used to configure the device while in sr mode to
	* enable power savings and to use the optical module LOS signal.
	* in power savings mode, the internal prbs checker can not be used.
	* if the optical module LOS signal is used as an input to the micro
	* code, then the micro code will wait until the optical module
	* LOS = 0 before turning on the adaptive equalizer.
	* Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
	* while setting bit 0 to 0 disables power savings mode.
	* Setting SPARE2_LSB bit 2 to 0 configures the device to use the
	* optical module LOS signal while setting bit 2 to 1 configures the
	* device so that it will ignore the optical module LOS SPARE2_LSB = 0
	*/

	/* enable power savings, ignore optical module LOS */
	{VILLA_MSEQ_SPARE2_LSB, 0x5},

	{VILLA_MSEQ_SPARE7_LSB, 0x1e},
	{VILLA_MSEQ_BANKSELECT, 0x4},
	{VILLA_MSEQ_SPARE9_LSB, 0x2},
	{VILLA_MSEQ_SPARE3_LSB, 0x0F53},
	{VILLA_MSEQ_SPARE3_MSB, 0x2006},
	{VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
	{VILLA_MSEQ_SPARE8_MSB, 0x0A46},
	{VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
	{VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
	{VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
	{VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
	{VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
	{VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
	{VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
	{VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
	{VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
	{VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
	{VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
	{VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
	{VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
	{VILLA_MSEQ_CAL_RX_SLICER, 0x80},
	{VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
	{VILLA_MSEQ_OPTIONS, 0x7},

	/* set up min value for ffe1 */
	{VILLA_MSEQ_COEF_INIT_SEL, 0x2},
	{VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},

	/* CS4315_sr_rx_pre_eq_set_4in */
	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
	{VILLA_MSEQ_OPTIONS, 0xf},
	{VILLA_MSEQ_BANKSELECT, 0x4},
	{VILLA_MSEQ_PC, 0x0},

	/* for lengths from 3.5 to 4.5inches */
	{VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
	{VILLA_MSEQ_SPARE25_LSB, 0x0306},
	{VILLA_MSEQ_SPARE21_LSB, 0x2},
	{VILLA_MSEQ_SPARE23_LSB, 0x2},
	{VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},

	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
	{VILLA_MSEQ_OPTIONS, 0x7},

	/* CS4315_rx_drive_4inch */
	/* for length 4inches */
	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
	{VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},

	/* CS4315_tx_drive_4inch */
	/* for length 4inches */
	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
	};

	void cs4340_upload_firmware(struct phy_device *phydev)
	{
	char line_temp[0x50] = {0};
	char reg_addr[0x50] = {0};
	char reg_data[0x50] = {0};
	int i, line_cnt = 0, column_cnt = 0;
	struct cortina_reg_config fw_temp;
	char *addr = NULL;

	#if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) \|\| \
	defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)

	addr = (char *)CONFIG_CORTINA_FW_ADDR;
	#elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
	int ret;
	size_t fw_length = CONFIG_CORTINA_FW_LENGTH;

	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
	ret = nand_read(get_nand_dev_by_index(0),
	(loff_t)CONFIG_CORTINA_FW_ADDR,
	&fw_length, (u_char *)addr);
	if (ret == -EUCLEAN) {
	printf("NAND read of Cortina firmware at 0x%x failed %d\n",
	CONFIG_CORTINA_FW_ADDR, ret);
	}
	#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
	int ret;
	struct spi_flash *ucode_flash;

	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
	CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
	if (!ucode_flash) {
	puts("SF: probe for Cortina ucode failed\n");
	} else {
	ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
	CONFIG_CORTINA_FW_LENGTH, addr);
	if (ret)
	puts("SF: read for Cortina ucode failed\n");
	spi_flash_free(ucode_flash);
	}
	#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
	int dev = CONFIG_SYS_MMC_ENV_DEV;
	u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
	u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);

	if (!mmc) {
	puts("Failed to find MMC device for Cortina ucode\n");
	} else {
	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
	printf("MMC read: dev # %u, block # %u, count %u ...\n",
	dev, blk, cnt);
	mmc_init(mmc);
	(void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt,
	addr);
	}
	#endif

	while (*addr != 'Q') {
	i = 0;

	while (*addr != 0x0a) {
	line_temp[i++] = *addr++;
	if (0x50 < i) {
	printf("Not found Cortina PHY ucode at 0x%p\n",
	(char *)CONFIG_CORTINA_FW_ADDR);
	return;
	}
	}

	addr++; /* skip '\n' */
	line_cnt++;
	column_cnt = i;
	line_temp[column_cnt] = '\0';

	if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
	return;

	for (i = 0; i < column_cnt; i++) {
	if (isspace(line_temp[i++]))
	break;
	}

	memcpy(reg_addr, line_temp, i);
	memcpy(reg_data, &line_temp[i], column_cnt - i);
	strim(reg_addr);
	strim(reg_data);
	fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
	fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
	0xffff;
	phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
	}
	}
	#endif

	int cs4340_phy_init(struct phy_device *phydev)
	{
	#ifndef CORTINA_NO_FW_UPLOAD
	int timeout = 100; /* 100ms */
	#endif
	int reg_value;

	/*
	* Cortina phy has provision to store
	* phy firmware in attached dedicated EEPROM.
	* Boards designed with EEPROM attached to Cortina
	* does not require FW upload.
	*/
	#ifndef CORTINA_NO_FW_UPLOAD
	/* step1: BIST test */
	phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL, 0x0004);
	phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
	phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL, 0x0001);
	while (--timeout) {
	reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
	if (reg_value & mseq_edc_bist_done) {
	if (0 == (reg_value & mseq_edc_bist_fail))
	break;
	}
	udelay(1000);
	}

	if (!timeout) {
	printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
	return -1;
	}

	/* setp2: upload ucode */
	cs4340_upload_firmware(phydev);
	#endif
	reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
	if (reg_value) {
	debug("%s checksum status failed.\n", __func__);
	return -1;
	}

	return 0;
	}

	int cs4340_config(struct phy_device *phydev)
	{
	cs4340_phy_init(phydev);
	return 0;
	}

	int cs4340_probe(struct phy_device *phydev)
	{
	phydev->flags = PHY_FLAG_BROKEN_RESET;
	return 0;
	}

	int cs4340_startup(struct phy_device *phydev)
	{
	phydev->link = 1;

	/* For now just lie and say it's 10G all the time */
	phydev->speed = SPEED_10000;
	phydev->duplex = DUPLEX_FULL;
	return 0;
	}

	struct phy_driver cs4340_driver = {
	.name = "Cortina CS4315/CS4340",
	.uid = PHY_UID_CS4340,
	.mask = 0xfffffff0,
	.features = PHY_10G_FEATURES,
	.mmds = (MDIO_DEVS_PMAPMD \| MDIO_DEVS_PCS \|
	MDIO_DEVS_PHYXS \| MDIO_DEVS_AN \|
	MDIO_DEVS_VEND1 \| MDIO_DEVS_VEND2),
	.config = &cs4340_config,
	.probe = &cs4340_probe,
	.startup = &cs4340_startup,
	.shutdown = &gen10g_shutdown,
	};

	int phy_cortina_init(void)
	{
	phy_register(&cs4340_driver);
	return 0;
	}

	int get_phy_id(struct mii_dev bus, int addr, int devad, u32 phy_id)
	{
	int phy_reg;

	/* Cortina PHY has non-standard offset of PHY ID registers */
	phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
	if (phy_reg < 0)
	return -EIO;
	*phy_id = (phy_reg & 0xffff) << 16;

	phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
	if (phy_reg < 0)
	return -EIO;
	*phy_id \|= (phy_reg & 0xffff);

	if (*phy_id == PHY_UID_CS4340)
	return 0;

	/*
	* If Cortina PHY not detected,
	* try generic way to find PHY ID registers
	*/
	phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
	if (phy_reg < 0)
	return -EIO;
	*phy_id = (phy_reg & 0xffff) << 16;

	phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
	if (phy_reg < 0)
	return -EIO;
	*phy_id \|= (phy_reg & 0xffff);

	return 0;
	}