ARM: dts: logicpd-som-lv: Resync DTS files with Linux 5.17-rc5
Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5
with some additional pending changes to address issues with
wrong pin-muxing on the OMAP35.
Signed-off-by: Adam Ford <aford173@gmail.com>
diff --git a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
index f7a841a..f690bc8 100644
--- a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
@@ -9,5 +9,19 @@
/ {
model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
- compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3";
+ compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
};
diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
index a604d92..e28e962 100644
--- a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
@@ -11,3 +11,17 @@
model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
};
+
+&omap3_pmx_core2 {
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+};
diff --git a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
index 100396f..7d0468a 100644
--- a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
+++ b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
@@ -51,6 +51,8 @@
&mcbsp2 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp2_pins>;
};
&charger {
@@ -77,7 +79,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
vdda_video-supply = <&video_reg>;
pinctrl-names = "default";
@@ -102,35 +104,18 @@
regulator-max-microvolt = <3300000>;
};
- lcd0: display@0 {
- compatible = "panel-dpi";
- label = "28";
- status = "okay";
- /* default-on; */
+ lcd0: display {
+ /* This isn't the exact LCD, but the timings meet spec */
+ compatible = "logicpd,type28";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pin>;
- enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
+ backlight = <&bl>;
+ enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
port {
lcd_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
-
- panel-timing {
- clock-frequency = <9000000>;
- hactive = <480>;
- vactive = <272>;
- hfront-porch = <3>;
- hback-porch = <2>;
- hsync-len = <42>;
- vback-porch = <3>;
- vfront-porch = <2>;
- vsync-len = <11>;
- hsync-active = <1>;
- vsync-active = <1>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
};
bl: backlight {
diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi
index b56524c..385bc8d 100644
--- a/arch/arm/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/dts/logicpd-som-lv.dtsi
@@ -27,6 +27,8 @@
/* HS USB Host PHY on PORT 1 */
hsusb2_phy: hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_reset_pin>;
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
#phy-cells = <0>;
@@ -144,6 +146,8 @@
};
&usbhshost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>, <&hsusb2_2_pins>;
port2-mode = "ehci-phy";
};
@@ -153,8 +157,6 @@
&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_pins>;
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
@@ -166,6 +168,7 @@
OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
>;
};
+
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
@@ -183,6 +186,7 @@
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
>;
};
+
mcspi1_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
@@ -250,13 +254,13 @@
};
&omap3_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_reset_pin>;
+
hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
+
wl127x_gpio: pinmux_wl127x_gpio_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
@@ -265,21 +269,6 @@
};
};
-&omap3_pmx_core2 {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_2_pins>;
- hsusb2_2_pins: pinmux_hsusb2_2_pins {
- pinctrl-single,pins = <
- OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
- OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
- OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
- OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
- OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
- OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
- >;
- };
-};
-
&uart2 {
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
pinctrl-names = "default";