| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Faraday FTGMAC100 Ethernet |
| * |
| * (C) Copyright 2009 Faraday Technology |
| * Po-Yu Chuang <ratbert@faraday-tech.com> |
| * |
| * (C) Copyright 2010 Andes Technology |
| * Macpaul Lin <macpaul@andestech.com> |
| * |
| * Copyright (C) 2018, IBM Corporation. |
| */ |
| |
| #include <clk.h> |
| #include <reset.h> |
| #include <cpu_func.h> |
| #include <dm.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <miiphy.h> |
| #include <net.h> |
| #include <wait_bit.h> |
| #include <asm/cache.h> |
| #include <dm/device_compat.h> |
| #include <linux/bitops.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/printk.h> |
| #include <linux/bitfield.h> |
| |
| #include "ftgmac100.h" |
| |
| /* Min frame ethernet frame size without FCS */ |
| #define ETH_ZLEN 60 |
| |
| /* Receive Buffer Size Register - HW default is 0x640 */ |
| #define FTGMAC100_RBSR_DEFAULT 0x640 |
| |
| /* PKTBUFSTX/PKTBUFSRX must both be power of 2 */ |
| #define PKTBUFSTX 4 /* must be power of 2 */ |
| |
| /* Timeout for transmit */ |
| #define FTGMAC100_TX_TIMEOUT_MS 1000 |
| |
| /* Timeout for a mdio read/write operation */ |
| #define FTGMAC100_MDIO_TIMEOUT_USEC 10000 |
| |
| /* |
| * MDC clock cycle threshold |
| * |
| * 20us * 100 = 2ms > (1 / 2.5Mhz) * 0x34 |
| */ |
| #define MDC_CYCTHR 0x34 |
| |
| /* |
| * ftgmac100 model variants |
| */ |
| enum ftgmac100_model { |
| FTGMAC100_MODEL_FARADAY, |
| FTGMAC100_MODEL_ASPEED, |
| FTGMAC100_MODEL_ASPEED_AST2700, |
| }; |
| |
| union ftgmac100_dma_addr { |
| dma_addr_t addr; |
| struct { |
| u32 lo; |
| u32 hi; |
| }; |
| }; |
| |
| /** |
| * struct ftgmac100_data - private data for the FTGMAC100 driver |
| * |
| * @iobase: The base address of the hardware registers |
| * @txdes: The array of transmit descriptors |
| * @rxdes: The array of receive descriptors |
| * @tx_index: Transmit descriptor index in @txdes |
| * @rx_index: Receive descriptor index in @rxdes |
| * @phy_addr: The PHY interface address to use |
| * @phydev: The PHY device backing the MAC |
| * @bus: The mdio bus |
| * @phy_mode: The mode of the PHY interface (rgmii, rmii, ...) |
| * @max_speed: Maximum speed of Ethernet connection supported by MAC |
| * @clks: The bulk of clocks assigned to the device in the DT |
| * @rxdes0_edorr_mask: The bit number identifying the end of the RX ring buffer |
| * @txdes0_edotr_mask: The bit number identifying the end of the TX ring buffer |
| */ |
| struct ftgmac100_data { |
| struct ftgmac100 *iobase; |
| |
| struct ftgmac100_txdes txdes[PKTBUFSTX] __aligned(ARCH_DMA_MINALIGN); |
| struct ftgmac100_rxdes rxdes[PKTBUFSRX] __aligned(ARCH_DMA_MINALIGN); |
| int tx_index; |
| int rx_index; |
| |
| u32 phy_addr; |
| struct phy_device *phydev; |
| struct mii_dev *bus; |
| u32 phy_mode; |
| u32 max_speed; |
| |
| struct clk_bulk clks; |
| struct reset_ctl *reset_ctl; |
| |
| /* End of RX/TX ring buffer bits. Depend on model */ |
| u32 rxdes0_edorr_mask; |
| u32 txdes0_edotr_mask; |
| |
| bool is_ast2700; |
| }; |
| |
| /* |
| * struct mii_bus functions |
| */ |
| static int ftgmac100_mdio_read(struct mii_dev *bus, int phy_addr, int dev_addr, |
| int reg_addr) |
| { |
| struct ftgmac100_data *priv = bus->priv; |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| int phycr; |
| int data; |
| int ret; |
| |
| phycr = FTGMAC100_PHYCR_MDC_CYCTHR(MDC_CYCTHR) | |
| FTGMAC100_PHYCR_PHYAD(phy_addr) | |
| FTGMAC100_PHYCR_REGAD(reg_addr) | |
| FTGMAC100_PHYCR_MIIRD; |
| writel(phycr, &ftgmac100->phycr); |
| |
| ret = readl_poll_timeout(&ftgmac100->phycr, phycr, |
| !(phycr & FTGMAC100_PHYCR_MIIRD), |
| FTGMAC100_MDIO_TIMEOUT_USEC); |
| if (ret) { |
| pr_err("%s: mdio read failed (phy:%d reg:%x)\n", |
| bus->name, phy_addr, reg_addr); |
| return ret; |
| } |
| |
| data = readl(&ftgmac100->phydata); |
| |
| return FTGMAC100_PHYDATA_MIIRDATA(data); |
| } |
| |
| static int ftgmac100_mdio_write(struct mii_dev *bus, int phy_addr, int dev_addr, |
| int reg_addr, u16 value) |
| { |
| struct ftgmac100_data *priv = bus->priv; |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| int phycr; |
| int data; |
| int ret; |
| |
| phycr = FTGMAC100_PHYCR_MDC_CYCTHR(MDC_CYCTHR) | |
| FTGMAC100_PHYCR_PHYAD(phy_addr) | |
| FTGMAC100_PHYCR_REGAD(reg_addr) | |
| FTGMAC100_PHYCR_MIIWR; |
| data = FTGMAC100_PHYDATA_MIIWDATA(value); |
| |
| writel(data, &ftgmac100->phydata); |
| writel(phycr, &ftgmac100->phycr); |
| |
| ret = readl_poll_timeout(&ftgmac100->phycr, phycr, |
| !(phycr & FTGMAC100_PHYCR_MIIWR), |
| FTGMAC100_MDIO_TIMEOUT_USEC); |
| if (ret) { |
| pr_err("%s: mdio write failed (phy:%d reg:%x)\n", |
| bus->name, phy_addr, reg_addr); |
| } |
| |
| return ret; |
| } |
| |
| static int ftgmac100_mdio_init(struct udevice *dev) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct mii_dev *bus; |
| int ret; |
| |
| bus = mdio_alloc(); |
| if (!bus) |
| return -ENOMEM; |
| |
| bus->read = ftgmac100_mdio_read; |
| bus->write = ftgmac100_mdio_write; |
| bus->priv = priv; |
| |
| ret = mdio_register_seq(bus, dev_seq(dev)); |
| if (ret) { |
| free(bus); |
| return ret; |
| } |
| |
| priv->bus = bus; |
| |
| return 0; |
| } |
| |
| static int ftgmac100_phy_adjust_link(struct ftgmac100_data *priv) |
| { |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| struct phy_device *phydev = priv->phydev; |
| u32 maccr; |
| |
| if (!phydev->link && priv->phy_mode != PHY_INTERFACE_MODE_NCSI) { |
| dev_err(phydev->dev, "No link\n"); |
| return -EREMOTEIO; |
| } |
| |
| /* read MAC control register and clear related bits */ |
| maccr = readl(&ftgmac100->maccr) & |
| ~(FTGMAC100_MACCR_GIGA_MODE | |
| FTGMAC100_MACCR_FAST_MODE | |
| FTGMAC100_MACCR_FULLDUP); |
| |
| if (phy_interface_is_rgmii(phydev) && phydev->speed == 1000) |
| maccr |= FTGMAC100_MACCR_GIGA_MODE; |
| |
| if (phydev->speed == 100) |
| maccr |= FTGMAC100_MACCR_FAST_MODE; |
| |
| if (phydev->duplex) |
| maccr |= FTGMAC100_MACCR_FULLDUP; |
| |
| /* update MII config into maccr */ |
| writel(maccr, &ftgmac100->maccr); |
| |
| return 0; |
| } |
| |
| static int ftgmac100_phy_init(struct udevice *dev) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct phy_device *phydev; |
| int ret; |
| |
| if (IS_ENABLED(CONFIG_DM_MDIO) && priv->phy_mode != PHY_INTERFACE_MODE_NCSI) |
| phydev = dm_eth_phy_connect(dev); |
| else |
| phydev = phy_connect(priv->bus, priv->phy_addr, dev, priv->phy_mode); |
| |
| if (!phydev) |
| return -ENODEV; |
| |
| if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI) |
| phydev->supported &= PHY_GBIT_FEATURES; |
| if (priv->max_speed) { |
| ret = phy_set_supported(phydev, priv->max_speed); |
| if (ret) |
| return ret; |
| } |
| phydev->advertising = phydev->supported; |
| priv->phydev = phydev; |
| phy_config(phydev); |
| |
| return 0; |
| } |
| |
| /* |
| * Reset MAC |
| */ |
| static void ftgmac100_reset(struct ftgmac100_data *priv) |
| { |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| |
| debug("%s()\n", __func__); |
| |
| setbits_le32(&ftgmac100->maccr, FTGMAC100_MACCR_SW_RST); |
| |
| while (readl(&ftgmac100->maccr) & FTGMAC100_MACCR_SW_RST) |
| ; |
| } |
| |
| /* |
| * Set MAC address |
| */ |
| static int ftgmac100_set_mac(struct ftgmac100_data *priv, |
| const unsigned char *mac) |
| { |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| unsigned int maddr = mac[0] << 8 | mac[1]; |
| unsigned int laddr = mac[2] << 24 | mac[3] << 16 | mac[4] << 8 | mac[5]; |
| |
| debug("%s(%x %x)\n", __func__, maddr, laddr); |
| |
| writel(maddr, &ftgmac100->mac_madr); |
| writel(laddr, &ftgmac100->mac_ladr); |
| |
| return 0; |
| } |
| |
| /* |
| * Get MAC address |
| */ |
| static int ftgmac100_get_mac(struct ftgmac100_data *priv, |
| unsigned char *mac) |
| { |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| unsigned int maddr = readl(&ftgmac100->mac_madr); |
| unsigned int laddr = readl(&ftgmac100->mac_ladr); |
| |
| debug("%s(%x %x)\n", __func__, maddr, laddr); |
| |
| mac[0] = (maddr >> 8) & 0xff; |
| mac[1] = maddr & 0xff; |
| mac[2] = (laddr >> 24) & 0xff; |
| mac[3] = (laddr >> 16) & 0xff; |
| mac[4] = (laddr >> 8) & 0xff; |
| mac[5] = laddr & 0xff; |
| |
| return 0; |
| } |
| |
| /* |
| * disable transmitter, receiver |
| */ |
| static void ftgmac100_stop(struct udevice *dev) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| |
| debug("%s()\n", __func__); |
| |
| writel(0, &ftgmac100->maccr); |
| |
| if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI) |
| phy_shutdown(priv->phydev); |
| } |
| |
| static int ftgmac100_start(struct udevice *dev) |
| { |
| struct eth_pdata *plat = dev_get_plat(dev); |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| union ftgmac100_dma_addr dma_addr = {.hi = 0, .lo = 0}; |
| struct phy_device *phydev = priv->phydev; |
| unsigned int maccr, dblac, desc_size; |
| ulong start, end; |
| int ret; |
| int i; |
| |
| debug("%s()\n", __func__); |
| |
| ftgmac100_reset(priv); |
| |
| /* set the ethernet address */ |
| ftgmac100_set_mac(priv, plat->enetaddr); |
| |
| /* disable all interrupts */ |
| writel(0, &ftgmac100->ier); |
| |
| /* initialize descriptors */ |
| priv->tx_index = 0; |
| priv->rx_index = 0; |
| |
| for (i = 0; i < PKTBUFSTX; i++) { |
| priv->txdes[i].txdes2 = 0; |
| priv->txdes[i].txdes3 = 0; |
| priv->txdes[i].txdes0 = 0; |
| } |
| priv->txdes[PKTBUFSTX - 1].txdes0 = priv->txdes0_edotr_mask; |
| |
| start = ((ulong)&priv->txdes[0]) & ~(ARCH_DMA_MINALIGN - 1); |
| end = start + roundup(sizeof(priv->txdes), ARCH_DMA_MINALIGN); |
| flush_dcache_range(start, end); |
| |
| for (i = 0; i < PKTBUFSRX; i++) { |
| unsigned int ip_align = 0; |
| |
| dma_addr.addr = (dma_addr_t)net_rx_packets[i]; |
| priv->rxdes[i].rxdes2 = FIELD_PREP(FTGMAC100_RXDES2_RXBUF_BADR_HI, dma_addr.hi); |
| /* For IP alignment */ |
| if ((dma_addr.lo & (PKTALIGN - 1)) == 0) |
| ip_align = 2; |
| priv->rxdes[i].rxdes3 = dma_addr.lo + ip_align; |
| priv->rxdes[i].rxdes0 = 0; |
| } |
| priv->rxdes[PKTBUFSRX - 1].rxdes0 = priv->rxdes0_edorr_mask; |
| |
| start = ((ulong)&priv->rxdes[0]) & ~(ARCH_DMA_MINALIGN - 1); |
| end = start + roundup(sizeof(priv->rxdes), ARCH_DMA_MINALIGN); |
| flush_dcache_range(start, end); |
| |
| /* transmit ring */ |
| dma_addr.addr = (dma_addr_t)priv->txdes; |
| writel(dma_addr.lo, &ftgmac100->txr_badr); |
| writel(dma_addr.hi, &ftgmac100->txr_badr_hi); |
| |
| /* receive ring */ |
| dma_addr.addr = (dma_addr_t)priv->rxdes; |
| writel(dma_addr.lo, &ftgmac100->rxr_badr); |
| writel(dma_addr.hi, &ftgmac100->rxr_badr_hi); |
| |
| /* Configure TX/RX decsriptor size |
| * This size is calculated based on cache line. |
| */ |
| desc_size = ARCH_DMA_MINALIGN / FTGMAC100_DESC_UNIT; |
| /* The descriptor size is at least 2 descriptor units. */ |
| if (desc_size < 2) |
| desc_size = 2; |
| dblac = readl(&ftgmac100->dblac) & ~GENMASK(19, 12); |
| dblac |= FTGMAC100_DBLAC_RXDES_SIZE(desc_size) | FTGMAC100_DBLAC_TXDES_SIZE(desc_size); |
| writel(dblac, &ftgmac100->dblac); |
| |
| /* poll receive descriptor automatically */ |
| writel(FTGMAC100_APTC_RXPOLL_CNT(1), &ftgmac100->aptc); |
| |
| /* config receive buffer size register */ |
| writel(FTGMAC100_RBSR_SIZE(FTGMAC100_RBSR_DEFAULT), &ftgmac100->rbsr); |
| |
| /* enable transmitter, receiver */ |
| maccr = FTGMAC100_MACCR_TXMAC_EN | |
| FTGMAC100_MACCR_RXMAC_EN | |
| FTGMAC100_MACCR_TXDMA_EN | |
| FTGMAC100_MACCR_RXDMA_EN | |
| FTGMAC100_MACCR_CRC_APD | |
| FTGMAC100_MACCR_FULLDUP | |
| FTGMAC100_MACCR_RX_RUNT | |
| FTGMAC100_MACCR_RX_BROADPKT; |
| |
| if (priv->is_ast2700 && (priv->phydev->interface == PHY_INTERFACE_MODE_RMII || |
| priv->phydev->interface == PHY_INTERFACE_MODE_NCSI)) |
| maccr |= FTGMAC100_MACCR_RMII_ENABLE; |
| |
| writel(maccr, &ftgmac100->maccr); |
| |
| ret = phy_startup(phydev); |
| if (ret) { |
| dev_err(phydev->dev, "Could not start PHY\n"); |
| return ret; |
| } |
| |
| ret = ftgmac100_phy_adjust_link(priv); |
| if (ret) { |
| dev_err(phydev->dev, "Could not adjust link\n"); |
| return ret; |
| } |
| |
| printf("%s: link up, %d Mbps %s-duplex mac:%pM\n", phydev->dev->name, |
| phydev->speed, phydev->duplex ? "full" : "half", plat->enetaddr); |
| |
| return 0; |
| } |
| |
| static int ftgmac100_free_pkt(struct udevice *dev, uchar *packet, int length) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct ftgmac100_rxdes *curr_des = &priv->rxdes[priv->rx_index]; |
| ulong des_start = ((ulong)curr_des) & ~(ARCH_DMA_MINALIGN - 1); |
| ulong des_end = des_start + |
| roundup(sizeof(*curr_des), ARCH_DMA_MINALIGN); |
| |
| /* |
| * Make sure there are no stale data in write-back over this area, which |
| * might get written into the memory while the ftgmac100 also writes |
| * into the same memory area. |
| */ |
| flush_dcache_range((ulong)net_rx_packets[priv->rx_index], |
| (ulong)net_rx_packets[priv->rx_index] + PKTSIZE_ALIGN); |
| |
| /* Release buffer to DMA and flush descriptor */ |
| curr_des->rxdes0 &= ~FTGMAC100_RXDES0_RXPKT_RDY; |
| flush_dcache_range(des_start, des_end); |
| |
| /* Move to next descriptor */ |
| priv->rx_index = (priv->rx_index + 1) % PKTBUFSRX; |
| |
| return 0; |
| } |
| |
| /* |
| * Get a data block via Ethernet |
| */ |
| static int ftgmac100_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct ftgmac100_rxdes *curr_des = &priv->rxdes[priv->rx_index]; |
| unsigned short rxlen; |
| ulong des_start = ((ulong)curr_des) & ~(ARCH_DMA_MINALIGN - 1); |
| ulong des_end = des_start + |
| roundup(sizeof(*curr_des), ARCH_DMA_MINALIGN); |
| union ftgmac100_dma_addr data_start = { .lo = 0, .hi = 0 }; |
| ulong data_end; |
| |
| data_start.hi = FIELD_GET(FTGMAC100_RXDES2_RXBUF_BADR_HI, curr_des->rxdes2); |
| data_start.lo = curr_des->rxdes3; |
| invalidate_dcache_range(des_start, des_end); |
| |
| if (!(curr_des->rxdes0 & FTGMAC100_RXDES0_RXPKT_RDY)) |
| return -EAGAIN; |
| |
| if (curr_des->rxdes0 & (FTGMAC100_RXDES0_RX_ERR | |
| FTGMAC100_RXDES0_CRC_ERR | |
| FTGMAC100_RXDES0_FTL | |
| FTGMAC100_RXDES0_RUNT | |
| FTGMAC100_RXDES0_RX_ODD_NB)) { |
| return -EAGAIN; |
| } |
| |
| rxlen = FTGMAC100_RXDES0_VDBC(curr_des->rxdes0); |
| |
| debug("%s(): RX buffer %d, %x received\n", |
| __func__, priv->rx_index, rxlen); |
| |
| /* Invalidate received data */ |
| data_end = data_start.addr + roundup(rxlen, ARCH_DMA_MINALIGN); |
| invalidate_dcache_range(data_start.addr, data_end); |
| *packetp = (uchar *)data_start.addr; |
| |
| return rxlen; |
| } |
| |
| static u32 ftgmac100_read_txdesc(const void *desc) |
| { |
| const struct ftgmac100_txdes *txdes = desc; |
| ulong des_start = ((ulong)txdes) & ~(ARCH_DMA_MINALIGN - 1); |
| ulong des_end = des_start + roundup(sizeof(*txdes), ARCH_DMA_MINALIGN); |
| |
| invalidate_dcache_range(des_start, des_end); |
| |
| return txdes->txdes0; |
| } |
| |
| BUILD_WAIT_FOR_BIT(ftgmac100_txdone, u32, ftgmac100_read_txdesc) |
| |
| /* |
| * Send a data block via Ethernet |
| */ |
| static int ftgmac100_send(struct udevice *dev, void *packet, int length) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| struct ftgmac100 *ftgmac100 = priv->iobase; |
| struct ftgmac100_txdes *curr_des = &priv->txdes[priv->tx_index]; |
| union ftgmac100_dma_addr dma_addr; |
| ulong des_start = ((ulong)curr_des) & ~(ARCH_DMA_MINALIGN - 1); |
| ulong des_end = des_start + |
| roundup(sizeof(*curr_des), ARCH_DMA_MINALIGN); |
| ulong data_start; |
| ulong data_end; |
| int rc; |
| |
| invalidate_dcache_range(des_start, des_end); |
| |
| if (curr_des->txdes0 & FTGMAC100_TXDES0_TXDMA_OWN) { |
| dev_err(dev, "no TX descriptor available\n"); |
| return -EPERM; |
| } |
| |
| debug("%s(%x, %x)\n", __func__, (int)packet, length); |
| |
| length = (length < ETH_ZLEN) ? ETH_ZLEN : length; |
| |
| dma_addr.addr = (dma_addr_t)packet; |
| curr_des->txdes2 = FIELD_PREP(FTGMAC100_TXDES2_TXBUF_BADR_HI, dma_addr.hi); |
| curr_des->txdes3 = dma_addr.lo; |
| |
| /* Flush data to be sent */ |
| data_start = (ulong)dma_addr.addr; |
| data_end = data_start + roundup(length, ARCH_DMA_MINALIGN); |
| flush_dcache_range(data_start, data_end); |
| |
| /* Only one segment on TXBUF */ |
| curr_des->txdes0 &= priv->txdes0_edotr_mask; |
| curr_des->txdes0 |= FTGMAC100_TXDES0_FTS | |
| FTGMAC100_TXDES0_LTS | |
| FTGMAC100_TXDES0_TXBUF_SIZE(length) | |
| FTGMAC100_TXDES0_TXDMA_OWN ; |
| |
| /* Flush modified buffer descriptor */ |
| flush_dcache_range(des_start, des_end); |
| |
| /* Start transmit */ |
| writel(1, &ftgmac100->txpd); |
| |
| rc = wait_for_bit_ftgmac100_txdone(curr_des, |
| FTGMAC100_TXDES0_TXDMA_OWN, false, |
| FTGMAC100_TX_TIMEOUT_MS, true); |
| if (rc) |
| return rc; |
| |
| debug("%s(): packet sent\n", __func__); |
| |
| /* Move to next descriptor */ |
| priv->tx_index = (priv->tx_index + 1) % PKTBUFSTX; |
| |
| return 0; |
| } |
| |
| static int ftgmac100_write_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| |
| return ftgmac100_set_mac(priv, pdata->enetaddr); |
| } |
| |
| static int ftgmac_read_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| |
| return ftgmac100_get_mac(priv, pdata->enetaddr); |
| } |
| |
| static int ftgmac100_of_to_plat(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| |
| pdata->iobase = dev_read_addr(dev); |
| |
| pdata->phy_interface = dev_read_phy_mode(dev); |
| if (pdata->phy_interface == PHY_INTERFACE_MODE_NA) |
| return -EINVAL; |
| |
| pdata->max_speed = dev_read_u32_default(dev, "max-speed", 0); |
| |
| if (dev_get_driver_data(dev) == FTGMAC100_MODEL_ASPEED) { |
| priv->rxdes0_edorr_mask = BIT(30); |
| priv->txdes0_edotr_mask = BIT(30); |
| priv->is_ast2700 = false; |
| } else if (dev_get_driver_data(dev) == FTGMAC100_MODEL_ASPEED_AST2700) { |
| priv->rxdes0_edorr_mask = BIT(30); |
| priv->txdes0_edotr_mask = BIT(30); |
| priv->is_ast2700 = true; |
| } else { |
| priv->rxdes0_edorr_mask = BIT(15); |
| priv->txdes0_edotr_mask = BIT(15); |
| } |
| |
| priv->reset_ctl = devm_reset_control_get_optional(dev, NULL); |
| |
| return clk_get_bulk(dev, &priv->clks); |
| } |
| |
| static int ftgmac100_probe(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_plat(dev); |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| int ret; |
| |
| priv->iobase = (struct ftgmac100 *)pdata->iobase; |
| priv->phy_mode = pdata->phy_interface; |
| priv->max_speed = pdata->max_speed; |
| priv->phy_addr = 0; |
| |
| if (dev_read_bool(dev, "use-ncsi")) |
| priv->phy_mode = PHY_INTERFACE_MODE_NCSI; |
| |
| #ifdef CONFIG_PHY_ADDR |
| priv->phy_addr = CONFIG_PHY_ADDR; |
| #endif |
| |
| ret = clk_enable_bulk(&priv->clks); |
| if (ret) |
| goto out; |
| |
| if (priv->reset_ctl) { |
| ret = reset_deassert(priv->reset_ctl); |
| if (ret) |
| goto out; |
| } |
| |
| /* |
| * If DM MDIO is enabled, the MDIO bus will be initialized later in |
| * dm_eth_phy_connect |
| */ |
| if (priv->phy_mode != PHY_INTERFACE_MODE_NCSI && |
| !IS_ENABLED(CONFIG_DM_MDIO)) { |
| ret = ftgmac100_mdio_init(dev); |
| if (ret) { |
| dev_err(dev, "Failed to initialize mdiobus: %d\n", ret); |
| goto out; |
| } |
| } |
| |
| ret = ftgmac100_phy_init(dev); |
| if (ret) { |
| dev_err(dev, "Failed to initialize PHY: %d\n", ret); |
| goto out; |
| } |
| |
| ftgmac_read_hwaddr(dev); |
| |
| out: |
| if (ret) |
| clk_release_bulk(&priv->clks); |
| |
| return ret; |
| } |
| |
| static int ftgmac100_remove(struct udevice *dev) |
| { |
| struct ftgmac100_data *priv = dev_get_priv(dev); |
| |
| free(priv->phydev); |
| mdio_unregister(priv->bus); |
| mdio_free(priv->bus); |
| if (priv->reset_ctl) |
| reset_assert(priv->reset_ctl); |
| clk_release_bulk(&priv->clks); |
| |
| return 0; |
| } |
| |
| static const struct eth_ops ftgmac100_ops = { |
| .start = ftgmac100_start, |
| .send = ftgmac100_send, |
| .recv = ftgmac100_recv, |
| .stop = ftgmac100_stop, |
| .free_pkt = ftgmac100_free_pkt, |
| .write_hwaddr = ftgmac100_write_hwaddr, |
| }; |
| |
| static const struct udevice_id ftgmac100_ids[] = { |
| { .compatible = "faraday,ftgmac100", .data = FTGMAC100_MODEL_FARADAY }, |
| { .compatible = "aspeed,ast2500-mac", .data = FTGMAC100_MODEL_ASPEED }, |
| { .compatible = "aspeed,ast2600-mac", .data = FTGMAC100_MODEL_ASPEED }, |
| { .compatible = "aspeed,ast2700-mac", .data = FTGMAC100_MODEL_ASPEED_AST2700 }, |
| {} |
| }; |
| |
| U_BOOT_DRIVER(ftgmac100) = { |
| .name = "ftgmac100", |
| .id = UCLASS_ETH, |
| .of_match = ftgmac100_ids, |
| .of_to_plat = ftgmac100_of_to_plat, |
| .probe = ftgmac100_probe, |
| .remove = ftgmac100_remove, |
| .ops = &ftgmac100_ops, |
| .priv_auto = sizeof(struct ftgmac100_data), |
| .plat_auto = sizeof(struct eth_pdata), |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, |
| }; |