diff --git a/board/BuR/brxre1/board.c b/board/BuR/brxre1/board.c
index 6639f22..0d1c6c4 100644
--- a/board/BuR/brxre1/board.c
+++ b/board/BuR/brxre1/board.c
@@ -23,49 +23,20 @@
 #include <asm/emif.h>
 #include <asm/gpio.h>
 #include <dm.h>
-#include <i2c.h>
 #include <power/tps65217.h>
 #include "../common/bur_common.h"
-#include <lcd.h>
+#include "../common/br_resetc.h"
 
 /* -------------------------------------------------------------------------*/
 /* -- defines for used GPIO Hardware -- */
-/* -- PSOC Resetcontroller Register defines -- */
 #define ESC_KEY					(0 + 19)
 #define LCD_PWR					(0 + 5)
 
-/* I2C Address of controller */
-#define	RSTCTRL_ADDR				0x75
-/* Register for CTRL-word */
-#define RSTCTRL_CTRLREG				0x01
-/* Register for giving some information to VxWorks OS */
-#define RSTCTRL_SCRATCHREG			0x04
-
-/* -- defines for RSTCTRL_CTRLREG  -- */
-#define	RSTCTRL_FORCE_PWR_NEN			0x0404
-#define	RSTCTRL_CAN_STB				0x4040
+#define	RSTCTRL_FORCE_PWR_NEN			0x04
+#define	RSTCTRL_CAN_STB				0x40
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static int rstctrl_rw(u8 reg, unsigned char rnw, void *pdat, int size)
-{
-	struct udevice *i2cdev;
-	int rc;
-
-	rc = i2c_get_chip_for_busnum(0, RSTCTRL_ADDR, 1, &i2cdev);
-	if (rc >= 0) {
-		if (rnw)
-			rc = dm_i2c_read(i2cdev, reg, pdat, size);
-		else
-			rc = dm_i2c_write(i2cdev, reg, pdat, size);
-	} else {
-		printf("%s: cannot get udevice for chip 0x%02x!\n",
-		       __func__, RSTCTRL_ADDR);
-	}
-
-	return rc;
-}
-
 #if defined(CONFIG_SPL_BUILD)
 static const struct ddr_data ddr3_data = {
 	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
@@ -108,7 +79,6 @@
 
 void am33xx_spl_board_init(void)
 {
-	unsigned short buf;
 	int rc;
 
 	struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
@@ -142,10 +112,10 @@
 	enable_i2c_pin_mux();
 
 	/* power-ON 3V3 via Resetcontroller */
-	buf = RSTCTRL_FORCE_PWR_NEN | RSTCTRL_CAN_STB;
-	rc = rstctrl_rw(RSTCTRL_CTRLREG, 0, (uint8_t *)&buf, sizeof(buf));
+	rc = br_resetc_regset(RSTCTRL_CTRLREG,
+			      RSTCTRL_FORCE_PWR_NEN | RSTCTRL_CAN_STB);
 	if (rc != 0)
-		printf("ERROR: cannot write to resetc (turn on PWR_nEN)\n");
+		printf("ERROR: cannot write to resetc (turn on PWR_nEN)!\n");
 
 	pmicsetup(0, 0);
 }
@@ -168,6 +138,9 @@
  */
 int board_init(void)
 {
+	/* request common used gpios */
+	gpio_request(ESC_KEY, "boot-key");
+
 	if (power_tps65217_init(0))
 		printf("WARN: cannot setup PMIC 0x24 @ bus #0, not found!.\n");
 
@@ -175,117 +148,19 @@
 }
 
 #ifdef CONFIG_BOARD_LATE_INIT
-int board_late_init(void)
-{
-	const unsigned int toff = 1000;
-	unsigned int cnt  = 3;
-	unsigned short buf = 0xAAAA;
-	unsigned char scratchreg = 0;
-	int rc;
 
-	/* try to read out some boot-instruction from resetcontroller */
-	rc = rstctrl_rw(RSTCTRL_SCRATCHREG, 1, &scratchreg, sizeof(scratchreg));
-	if (rc != 0)
-		printf("ERROR: read scratchregister (resetc) failed!\n");
+int board_boot_key(void)
+{
+	return gpio_get_value(ESC_KEY);
+}
 
-	if (gpio_request(ESC_KEY, "boot-key") != 0) {
-		printf("cannot request boot-key!\n");
-	} else if (gpio_get_value(ESC_KEY)) {
-		do {
-			lcd_position_cursor(1, 8);
-			switch (cnt) {
-			case 3:
-				lcd_puts(
-				"release ESC-KEY to enter SERVICE-mode.");
-				break;
-			case 2:
-				lcd_puts(
-				"release ESC-KEY to enter DIAGNOSE-mode.");
-				break;
-			case 1:
-				lcd_puts(
-				"release ESC-KEY to enter BOOT-mode.    ");
-				break;
-			}
-			mdelay(toff);
-			cnt--;
-			if (!gpio_get_value(ESC_KEY) &&
-			    gpio_get_value(PUSH_KEY) && 2 == cnt) {
-				lcd_position_cursor(1, 8);
-				lcd_puts(
-				"switching to network-console ...       ");
-				env_set("bootcmd", "run netconsole");
-				cnt = 4;
-				break;
-			} else if (!gpio_get_value(ESC_KEY) &&
-			    gpio_get_value(PUSH_KEY) && 1 == cnt) {
-				lcd_position_cursor(1, 8);
-				lcd_puts(
-				"starting u-boot script from USB ...    ");
-				env_set("bootcmd", "run usbscript");
-				cnt = 4;
-				break;
-			} else if ((!gpio_get_value(ESC_KEY) &&
-				    gpio_get_value(PUSH_KEY) && cnt == 0) ||
-				    (gpio_get_value(ESC_KEY) &&
-				    gpio_get_value(PUSH_KEY) && cnt == 0)) {
-				lcd_position_cursor(1, 8);
-				lcd_puts(
-				"starting script from network ...      ");
-				env_set("bootcmd", "run netscript");
-				cnt = 4;
-				break;
-			} else if (!gpio_get_value(ESC_KEY)) {
-				break;
-			}
-		} while (cnt);
-	} else if (scratchreg == 0xCC) {
-		lcd_position_cursor(1, 8);
-		lcd_puts(
-		"starting vxworks from network ...      ");
-		env_set("bootcmd", "run netboot");
-		cnt = 4;
-	} else if (scratchreg == 0xCD) {
-		lcd_position_cursor(1, 8);
-		lcd_puts(
-		"starting script from network ...      ");
-		env_set("bootcmd", "run netscript");
-		cnt = 4;
-	} else if (scratchreg == 0xCE) {
-		lcd_position_cursor(1, 8);
-		lcd_puts(
-		"starting AR from eMMC ...             ");
-		env_set("bootcmd", "run mmcboot");
-		cnt = 4;
-	}
+int board_late_init(void)
+{
+	char othbootargs[128];
 
-	lcd_position_cursor(1, 8);
-	switch (cnt) {
-	case 0:
-		lcd_puts("entering BOOT-mode.                    ");
-		env_set("bootcmd", "run defaultAR");
-		buf = 0x0000;
-		break;
-	case 1:
-		lcd_puts("entering DIAGNOSE-mode.                ");
-		buf = 0x0F0F;
-		break;
-	case 2:
-		lcd_puts("entering SERVICE mode.                 ");
-		buf = 0xB4B4;
-		break;
-	case 3:
-		lcd_puts("loading OS...                          ");
-		buf = 0x0404;
-		break;
-	}
-	/* write bootinfo into scratchregister of resetcontroller */
-	rc = rstctrl_rw(RSTCTRL_SCRATCHREG, 0, (uint8_t *)&buf, sizeof(buf));
-	if (rc != 0)
-		printf("ERROR: write scratchregister (resetc) failed!\n");
+	br_resetc_bmode();
 
 	/* setup othbootargs for bootvx-command (vxWorks bootline) */
-	char othbootargs[128];
 	snprintf(othbootargs, sizeof(othbootargs),
 		 "u=vxWorksFTP pw=vxWorks o=0x%08x;0x%08x;0x%08x;0x%08x",
 		 (u32)gd->fb_base - 0x20,