armv8: ls1046aqds: Add LS1046AQDS board support
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/include/configs/ls1046aqds.h b/include/configs/ls1046aqds.h
new file mode 100644
index 0000000..2e5c2f1
--- /dev/null
+++ b/include/configs/ls1046aqds.h
@@ -0,0 +1,487 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1046AQDS_H__
+#define __LS1046AQDS_H__
+
+#include "ls1046a_common.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
+#define CONFIG_SYS_TEXT_BASE 0x82000000
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_TEXT_BASE 0x40010000
+#else
+#define CONFIG_SYS_TEXT_BASE 0x60100000
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define CONFIG_DDR_SPD
+#define SPD_EEPROM_ADDRESS 0x51
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_SYS_HAS_SERDES
+
+/* DSPI */
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO /* cs0 */
+#define CONFIG_SPI_FLASH_SST /* cs1 */
+#define CONFIG_SPI_FLASH_EON /* cs2 */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS 1
+#define CONFIG_SF_DEFAULT_CS 0
+#endif
+#endif
+
+/* QSPI */
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE (1 << 24)
+#define FSL_QSPI_FLASH_NUM 2
+#endif
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHYLIB_10G
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+/* PHY address on QSGMII riser card on slot 2 */
+#define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
+#define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
+#define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
+#define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
+#endif
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI \
+ board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SYS_FSL_PBL_RCW \
+ board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
+#endif
+
+#ifdef CONFIG_SD_BOOT
+#ifdef CONFIG_SD_BOOT_QSPI
+#define CONFIG_SYS_FSL_PBL_RCW \
+ board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
+#else
+#define CONFIG_SYS_FSL_PBL_RCW \
+ board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
+#endif
+#endif
+
+/* IFC */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_FSL_IFC
+/*
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE 0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+#endif
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024)
+
+#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_TRHZ_80)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1a) | \
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0xe) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS, \
+ CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
+
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE 0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x7) | \
+ FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0xe) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
+ FTIM2_NAND_TREH(0xa) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * 1024)
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SPL_PAD_TO 0x40000 /* block aligned */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#endif
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define CONFIG_SYS_I2C_EARLY_INIT
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+/*
+ * QIXIS Definitions
+ */
+#define CONFIG_FSL_QIXIS
+
+#ifdef CONFIG_FSL_QIXIS
+#define QIXIS_BASE 0x7fb00000
+#define QIXIS_BASE_PHYS QIXIS_BASE
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_LBMAP_NAND 0x09
+#define QIXIS_LBMAP_SD 0x00
+#define QIXIS_LBMAP_SD_QSPI 0xff
+#define QIXIS_LBMAP_QSPI 0xff
+#define QIXIS_RCW_SRC_NAND 0x110
+#define QIXIS_RCW_SRC_SD 0x040
+#define QIXIS_RCW_SRC_QSPI 0x045
+#define QIXIS_RST_CTL_RESET 0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+
+#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
+#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_NOR_MODE_AVD_NOR | \
+ CSOR_NOR_TRHZ_80)
+
+/*
+ * QIXIS Timing parameters for IFC GPCM
+ */
+#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xc) | \
+ FTIM0_GPCM_TEADC(0x20) | \
+ FTIM0_GPCM_TEAHC(0x10))
+#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0x50) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0x8) | \
+ FTIM2_GPCM_TCH(0x8) | \
+ FTIM2_GPCM_TWP(0xf0))
+#define CONFIG_SYS_FPGA_FTIM3 0x0
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0
+#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1
+#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2
+#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0
+#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1
+#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2
+#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3
+#endif
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI 0x77
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR 0x18
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_CH7301 0xC
+#define I2C_MUX_CH5 0xD
+#define I2C_MUX_CH6 0xE
+#define I2C_MUX_CH7 0xF
+
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+
+#define CONFIG_VID_FLS_ENV "ls1046aqds_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+#define CONFIG_VOL_MONITOR_IR36021_SET
+#define CONFIG_VOL_MONITOR_INA220
+/* The lowest and highest voltage allowed for LS1046AQDS */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * Stack sizes
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (30 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x20000
+#endif
+
+#define CONFIG_CMDLINE_TAG
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \
+ "e0000 f00000 && bootm $kernel_load"
+#else
+#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
+ "$kernel_size && bootm $kernel_load"
+#endif
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
+ "14m(free)"
+#else
+#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \
+ "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \
+ "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \
+ "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \
+ "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \
+ "40m(nor_bank4_fit);7e800000.flash:" \
+ "4m(nand_uboot),36m(nand_kernel)," \
+ "472m(nand_free);spi0.0:2m(uboot)," \
+ "14m(free)"
+#endif
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1046AQDS_H__ */