Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master'
diff --git a/Makefile b/Makefile
index 7310c4e..0d86b55 100644
--- a/Makefile
+++ b/Makefile
@@ -350,12 +350,14 @@
# enable combined SPL/u-boot/dtb rules for tegra
ifneq ($(CONFIG_TEGRA),)
+ifeq ($(CONFIG_SPL),y)
ifeq ($(CONFIG_OF_SEPARATE),y)
ALL-y += $(obj)u-boot-dtb-tegra.bin
else
ALL-y += $(obj)u-boot-nodtb-tegra.bin
endif
endif
+endif
build := -f $(TOPDIR)/scripts/Makefile.build -C
diff --git a/arch/arm/cpu/arm720t/tegra-common/cpu.c b/arch/arm/cpu/arm720t/tegra-common/cpu.c
index 9294611..72c69b9 100644
--- a/arch/arm/cpu/arm720t/tegra-common/cpu.c
+++ b/arch/arm/cpu/arm720t/tegra-common/cpu.c
@@ -49,33 +49,68 @@
* Timing tables for each SOC for all four oscillator options.
*/
struct clk_pll_table tegra_pll_x_table[TEGRA_SOC_CNT][CLOCK_OSC_FREQ_COUNT] = {
- /* T20: 1 GHz */
- /* n, m, p, cpcon */
- {{ 1000, 13, 0, 12}, /* OSC 13M */
- { 625, 12, 0, 8}, /* OSC 19.2M */
- { 1000, 12, 0, 12}, /* OSC 12M */
- { 1000, 26, 0, 12}, /* OSC 26M */
+ /*
+ * T20: 1 GHz
+ *
+ * Register Field Bits Width
+ * ------------------------------
+ * PLLX_BASE p 22:20 3
+ * PLLX_BASE n 17: 8 10
+ * PLLX_BASE m 4: 0 5
+ * PLLX_MISC cpcon 11: 8 4
+ */
+ {
+ { .n = 1000, .m = 13, .p = 0, .cpcon = 12 }, /* OSC: 13.0 MHz */
+ { .n = 625, .m = 12, .p = 0, .cpcon = 8 }, /* OSC: 19.2 MHz */
+ { .n = 1000, .m = 12, .p = 0, .cpcon = 12 }, /* OSC: 12.0 MHz */
+ { .n = 1000, .m = 26, .p = 0, .cpcon = 12 }, /* OSC: 26.0 MHz */
},
-
- /* T25: 1.2 GHz */
- {{ 923, 10, 0, 12},
- { 750, 12, 0, 8},
- { 600, 6, 0, 12},
- { 600, 13, 0, 12},
+ /*
+ * T25: 1.2 GHz
+ *
+ * Register Field Bits Width
+ * ------------------------------
+ * PLLX_BASE p 22:20 3
+ * PLLX_BASE n 17: 8 10
+ * PLLX_BASE m 4: 0 5
+ * PLLX_MISC cpcon 11: 8 4
+ */
+ {
+ { .n = 923, .m = 10, .p = 0, .cpcon = 12 }, /* OSC: 13.0 MHz */
+ { .n = 750, .m = 12, .p = 0, .cpcon = 8 }, /* OSC: 19.2 MHz */
+ { .n = 600, .m = 6, .p = 0, .cpcon = 12 }, /* OSC: 12.0 MHz */
+ { .n = 600, .m = 13, .p = 0, .cpcon = 12 }, /* OSC: 26.0 MHz */
},
-
- /* T30: 1.4 GHz */
- {{ 862, 8, 0, 8},
- { 583, 8, 0, 4},
- { 700, 6, 0, 8},
- { 700, 13, 0, 8},
+ /*
+ * T30: 1.4 GHz
+ *
+ * Register Field Bits Width
+ * ------------------------------
+ * PLLX_BASE p 22:20 3
+ * PLLX_BASE n 17: 8 10
+ * PLLX_BASE m 4: 0 5
+ * PLLX_MISC cpcon 11: 8 4
+ */
+ {
+ { .n = 862, .m = 8, .p = 0, .cpcon = 8 }, /* OSC: 13.0 MHz */
+ { .n = 583, .m = 8, .p = 0, .cpcon = 4 }, /* OSC: 19.2 MHz */
+ { .n = 700, .m = 6, .p = 0, .cpcon = 8 }, /* OSC: 12.0 MHz */
+ { .n = 700, .m = 13, .p = 0, .cpcon = 8 }, /* OSC: 26.0 MHz */
},
-
- /* T114: 1.4 GHz */
- {{ 862, 8, 0, 8},
- { 583, 8, 0, 4},
- { 696, 12, 0, 8},
- { 700, 13, 0, 8},
+ /*
+ * T114: 700 MHz
+ *
+ * Register Field Bits Width
+ * ------------------------------
+ * PLLX_BASE p 23:20 4
+ * PLLX_BASE n 15: 8 8
+ * PLLX_BASE m 7: 0 8
+ */
+ {
+ { .n = 108, .m = 1, .p = 1 }, /* OSC: 13.0 MHz */
+ { .n = 73, .m = 1, .p = 1 }, /* OSC: 19.2 MHz */
+ { .n = 116, .m = 1, .p = 1 }, /* OSC: 12.0 MHz */
+ { .n = 108, .m = 2, .p = 1 }, /* OSC: 26.0 MHz */
},
};
@@ -100,6 +135,7 @@
int pllx_set_rate(struct clk_pll_simple *pll , u32 divn, u32 divm,
u32 divp, u32 cpcon)
{
+ int chip = tegra_get_chip();
u32 reg;
/* If PLLX is already enabled, just return */
@@ -116,7 +152,10 @@
writel(reg, &pll->pll_base);
/* Set cpcon to PLLX_MISC */
- reg = (cpcon << PLL_CPCON_SHIFT);
+ if (chip == CHIPID_TEGRA20 || chip == CHIPID_TEGRA30)
+ reg = (cpcon << PLL_CPCON_SHIFT);
+ else
+ reg = 0;
/* Set dccon to PLLX_MISC if freq > 600MHz */
if (divn > 600)
diff --git a/arch/arm/cpu/tegra-common/ap.c b/arch/arm/cpu/tegra-common/ap.c
index 6fb11cb..60d71a6 100644
--- a/arch/arm/cpu/tegra-common/ap.c
+++ b/arch/arm/cpu/tegra-common/ap.c
@@ -71,6 +71,7 @@
switch (sku_id) {
case SKU_ID_T33:
case SKU_ID_T30:
+ case SKU_ID_TM30MQS_P_A3:
return TEGRA_SOC_T30;
}
break;
diff --git a/arch/arm/include/asm/arch-tegra/clock.h b/arch/arm/include/asm/arch-tegra/clock.h
index c3174bd..e7d0fd4 100644
--- a/arch/arm/include/asm/arch-tegra/clock.h
+++ b/arch/arm/include/asm/arch-tegra/clock.h
@@ -113,9 +113,9 @@
enum crc_reset_id {
/* Things we can hold in reset for each CPU */
crc_rst_cpu = 1,
- crc_rst_de = 1 << 2, /* What is de? */
- crc_rst_watchdog = 1 << 3,
- crc_rst_debug = 1 << 4,
+ crc_rst_de = 1 << 4, /* What is de? */
+ crc_rst_watchdog = 1 << 8,
+ crc_rst_debug = 1 << 12,
};
/**
diff --git a/arch/arm/include/asm/arch-tegra/tegra.h b/arch/arm/include/asm/arch-tegra/tegra.h
index 25d1fc4..e99f681 100644
--- a/arch/arm/include/asm/arch-tegra/tegra.h
+++ b/arch/arm/include/asm/arch-tegra/tegra.h
@@ -65,6 +65,7 @@
SKU_ID_T25E = 0x1c,
SKU_ID_T33 = 0x80,
SKU_ID_T30 = 0x81, /* Cardhu value */
+ SKU_ID_TM30MQS_P_A3 = 0xb1,
SKU_ID_T114_ENG = 0x00, /* Dalmore value, unfused */
SKU_ID_T114_1 = 0x01,
};
diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
index 6f67c34..17a2a40 100644
--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c
+++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
@@ -271,7 +271,6 @@
#endif
#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 0);
at91_spi0_hw_init(1 << 4);
#endif
diff --git a/board/avionic-design/common/pinmux-config-tamonten-ng.h b/board/avionic-design/common/pinmux-config-tamonten-ng.h
new file mode 100644
index 0000000..39df731
--- /dev/null
+++ b/board/avionic-design/common/pinmux-config-tamonten-ng.h
@@ -0,0 +1,385 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _PINMUX_CONFIG_TAMONTEN_NG_H_
+#define _PINMUX_CONFIG_TAMONTEN_NG_H_
+
+#define DEFAULT_PINMUX(_pingroup, _mux, _pull, _tri, _io) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_DEFAULT, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define I2C_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_##_od, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define LV_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _ioreset) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_##_ioreset \
+ }
+
+#define DEFAULT_PADCFG(_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \
+ { \
+ .padgrp = PDRIVE_PINGROUP_##_padgrp, \
+ .slwf = _slwf, \
+ .slwr = _slwr, \
+ .drvup = _drvup, \
+ .drvdn = _drvdn, \
+ .lpmd = PGRP_LPMD_##_lpmd, \
+ .schmt = PGRP_SCHMT_##_schmt, \
+ .hsm = PGRP_HSM_##_hsm, \
+ }
+
+static struct pingroup_config tamonten_ng_pinmux_common[] = {
+ /* SDMMC1 pinmux */
+ DEFAULT_PINMUX(SDMMC1_CLK, SDMMC1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_CMD, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT0, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT1, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT2, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT3, SDMMC1, UP, NORMAL, INPUT),
+
+ /* SDMMC3 pinmux */
+ DEFAULT_PINMUX(SDMMC3_CLK, SDMMC3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_CMD, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT0, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT1, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT2, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT3, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT4, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT5, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT6, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT7, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_IORDY, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_CS6_N, RSVD1, UP, NORMAL, INPUT),
+
+ /* SDMMC4 pinmux */
+ LV_PINMUX(SDMMC4_CLK, SDMMC4, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_CMD, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT0, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT1, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT2, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT3, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT4, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT5, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT6, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT7, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_RST_N, RSVD1, DOWN, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* I2C1 pinmux */
+ I2C_PINMUX(GEN1_I2C_SCL, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN1_I2C_SDA, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C2 pinmux */
+ I2C_PINMUX(GEN2_I2C_SCL, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN2_I2C_SDA, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C3 pinmux */
+ I2C_PINMUX(CAM_I2C_SCL, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(CAM_I2C_SDA, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C4 pinmux */
+ I2C_PINMUX(DDC_SCL, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(DDC_SDA, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* Power I2C pinmux */
+ I2C_PINMUX(PWR_I2C_SCL, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(PWR_I2C_SDA, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* UART1 */
+ DEFAULT_PINMUX(ULPI_DATA0, UARTA, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DATA1, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 */
+ DEFAULT_PINMUX(UART2_RXD, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_TXD, UARTB, NORMAL, NORMAL, OUTPUT),
+
+ /* UART3 */
+ DEFAULT_PINMUX(UART3_TXD, UARTC, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(UART3_RXD, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_CTS_N, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_RTS_N, UARTC, NORMAL, NORMAL, OUTPUT),
+
+ /* UART4 */
+ DEFAULT_PINMUX(ULPI_CLK, UARTD, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DIR, UARTD, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_NXT, UARTD, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_STP, UARTD, NORMAL, NORMAL, OUTPUT),
+
+ /* DAP */
+ DEFAULT_PINMUX(CLK1_OUT, EXTPERIPH1, NORMAL, NORMAL, INPUT),
+
+ /* I2S1 */
+ DEFAULT_PINMUX(DAP2_FS, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DIN, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DOUT, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_SCLK, I2S1, NORMAL, NORMAL, INPUT),
+
+ /* SPDIF */
+ DEFAULT_PINMUX(SPDIF_IN, SPDIF, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPDIF_OUT, SPDIF, NORMAL, NORMAL, OUTPUT),
+
+ /* I2S2 */
+ DEFAULT_PINMUX(DAP3_FS, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DIN, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DOUT, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_SCLK, I2S2, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 */
+ DEFAULT_PINMUX(DAP4_FS, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_DIN, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_SCLK, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO */
+ DEFAULT_PINMUX(GPIO_PV2, RSVD1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GPIO_PV3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI2_CS1_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD */
+ DEFAULT_PINMUX(LCD_PWR1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDIN, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDOUT, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_WR_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS0_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SCK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PCLK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DE, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_HSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_VSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D3, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D4, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D5, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D6, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D7, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D8, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D9, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D10, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D11, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D12, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D13, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D14, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D15, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D16, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D17, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D18, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D19, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D20, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D21, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D22, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D23, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS1_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_M1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CRT_HSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CRT_VSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+
+ /* BT656 */
+ LV_PINMUX(VI_MCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_PCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_HSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_VSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D2, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D3, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D4, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D5, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D6, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D7, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D8, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D9, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D11, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIOs */
+ DEFAULT_PINMUX(GPIO_PU5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD12, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD BL */
+ DEFAULT_PINMUX(GMI_AD8, PWM0, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD10, RSVD4, NORMAL, NORMAL, OUTPUT),
+
+ /* SPI4 */
+ DEFAULT_PINMUX(GMI_A16, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A17, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A18, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A19, SPI4, NORMAL, NORMAL, INPUT),
+
+ /* Video input GPIO */
+ DEFAULT_PINMUX(GPIO_PCC1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB7, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Sensor GPIO */
+ DEFAULT_PINMUX(GPIO_PCC2, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* JTAG */
+ DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, OUTPUT),
+
+ /* Power controls */
+ DEFAULT_PINMUX(GMI_CS2_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* SPI1 */
+ DEFAULT_PINMUX(SPI1_MOSI, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_SCK, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_CS0_N, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_MISO, SPI1, NORMAL, NORMAL, INPUT),
+
+ /* PMU */
+ DEFAULT_PINMUX(GPIO_PV0, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SYS_CLK_REQ, SYSCLK, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CLK_32K_IN, SYSCLK, NORMAL, NORMAL, INPUT),
+
+ /* PCI */
+ DEFAULT_PINMUX(PEX_L0_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L0_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L0_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_WAKE_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L1_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L2_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+
+ /* HDMI */
+ DEFAULT_PINMUX(HDMI_CEC, CEC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(HDMI_INT, RSVD1, NORMAL, TRISTATE, INPUT),
+};
+
+static struct pingroup_config unused_pins_lowpower[] = {
+ /* UART1 - NC */
+ DEFAULT_PINMUX(ULPI_DATA2, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA3, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA4, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA5, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA6, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA7, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 - NC */
+ DEFAULT_PINMUX(UART2_RTS_N, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_CTS_N, UARTB, NORMAL, NORMAL, INPUT),
+
+ /* DAP - NC */
+ DEFAULT_PINMUX(CLK1_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 - NC */
+ DEFAULT_PINMUX(DAP4_DOUT, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO - NC */
+ DEFAULT_PINMUX(CLK2_OUT, EXTPERIPH2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK2_REQ, DAP, NORMAL, NORMAL, INPUT),
+
+ /* BT656 - NC */
+ LV_PINMUX(VI_D0, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D1, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D10, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIO - NC */
+ DEFAULT_PINMUX(GPIO_PU0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU2, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Video input - NC */
+ DEFAULT_PINMUX(CAM_MCLK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW11, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* KBC keys - NC */
+ DEFAULT_PINMUX(KB_ROW0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW7, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW8, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW9, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW10, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW12, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW13, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW14, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW15, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL7, KBC, UP, NORMAL, INPUT),
+
+ /* PMU - NC */
+ DEFAULT_PINMUX(CLK_32K_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Power rails GPIO - NC */
+ DEFAULT_PINMUX(SPI2_SCK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Others - NC */
+ DEFAULT_PINMUX(GMI_WP_N, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PV1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WAIT, NAND, UP, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_ADV_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CLK, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS3_N, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS7_N, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD0, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD1, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD2, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD3, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD4, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD5, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD6, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD7, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD9, PWM1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD11, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD13, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WR_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_OE_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_DQS, NAND, NORMAL, TRISTATE, OUTPUT),
+};
+
+static struct padctrl_config tamonten_ng_padctrl[] = {
+ /* (_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */
+ DEFAULT_PADCFG(SDIO1, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR,
+ SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, DISABLE, DISABLE),
+};
+#endif /* _PINMUX_CONFIG_TAMONTEN_NG_H_ */
diff --git a/board/avionic-design/common/tamonten-ng.c b/board/avionic-design/common/tamonten-ng.c
new file mode 100644
index 0000000..9d395c6
--- /dev/null
+++ b/board/avionic-design/common/tamonten-ng.c
@@ -0,0 +1,85 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/gp_padctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include "pinmux-config-tamonten-ng.h"
+#include <i2c.h>
+
+#define PMU_I2C_ADDRESS 0x2D
+
+#define PMU_REG_LDO5 0x32
+
+#define PMU_REG_LDO_HIGH_POWER 1
+
+/* Voltage selection for the LDOs with 100mV resolution */
+#define PMU_REG_LDO_SEL_100(mV) ((((mV - 1000) / 100) + 2) << 2)
+
+#define PMU_REG_LDO_100(st, mV) (PMU_REG_LDO_##st | PMU_REG_LDO_SEL_100(mV))
+
+#define PMU_LDO5(st, mV) PMU_REG_LDO_100(st, mV)
+
+void pinmux_init(void)
+{
+ pinmux_config_table(tamonten_ng_pinmux_common,
+ ARRAY_SIZE(tamonten_ng_pinmux_common));
+ pinmux_config_table(unused_pins_lowpower,
+ ARRAY_SIZE(unused_pins_lowpower));
+
+ /* Initialize any non-default pad configs (APB_MISC_GP regs) */
+ padgrp_config_table(tamonten_ng_padctrl,
+ ARRAY_SIZE(tamonten_ng_padctrl));
+}
+
+void gpio_early_init(void)
+{
+ /* Turn on the alive signal */
+ gpio_request(GPIO_PV2, "ALIVE");
+ gpio_direction_output(GPIO_PV2, 1);
+
+ /* Remove the reset on the external periph */
+ gpio_request(GPIO_PI4, "nRST_PERIPH");
+ gpio_direction_output(GPIO_PI4, 1);
+}
+
+void pmu_write(uchar reg, uchar data)
+{
+ i2c_set_bus_num(4); /* PMU is on bus 4 */
+ i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1);
+}
+
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+ /* Enable LDO5 with 3.3v for SDMMC3 */
+ pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
+
+ /* Switch the power on */
+ gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
+ gpio_direction_output(GPIO_PJ2, 1);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+ /*
+ * NOTE: We don't do mmc-specific pin muxes here.
+ * They were done globally in pinmux_init().
+ */
+
+ /* Bring up the SDIO1 power rail */
+ board_sdmmc_voltage_init();
+}
diff --git a/board/avionic-design/dts/tegra30-tamonten.dtsi b/board/avionic-design/dts/tegra30-tamonten.dtsi
new file mode 100644
index 0000000..50d5762
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tamonten.dtsi
@@ -0,0 +1,69 @@
+#include "tegra30.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten NG";
+ compatible = "ad,tamonten-ng", "nvidia,tegra30";
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ aliases {
+ i2c0 = "/i2c@7000c000";
+ i2c1 = "/i2c@7000c700";
+ i2c2 = "/i2c@7000c400";
+ i2c3 = "/i2c@7000c500";
+ i2c4 = "/i2c@7000d000";
+ sdhci0 = "/sdhci@78000600";
+ sdhci1 = "/sdhci@78000400";
+ sdhci2 = "/sdhci@78000000";
+ usb0 = "/usb@7d008000";
+ };
+
+ /* GEN1 */
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* GEN2 */
+ i2c@7000c400 {
+ clock-frequency = <100000>;
+ };
+
+ /* CAM */
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* DDC */
+ i2c@7000c700 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* PWR */
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* SD slot on the base board */
+ sdhci@78000400 {
+ cd-gpios = <&gpio 69 1>; /* gpio PI5 */
+ wp-gpios = <&gpio 67 0>; /* gpio PI3 */
+ bus-width = <4>;
+ };
+
+ /* EMMC on the COM module */
+ sdhci@78000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ usb@7d008000 {
+ status = "okay";
+ };
+
+};
diff --git a/board/avionic-design/dts/tegra30-tec-ng.dts b/board/avionic-design/dts/tegra30-tec-ng.dts
new file mode 100644
index 0000000..8a69e81
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tec-ng.dts
@@ -0,0 +1,18 @@
+/dts-v1/;
+
+#include "tegra30-tamonten.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten™ NG Evaluation Carrier";
+ compatible = "ad,tec-ng", "nvidia,tegra30";
+
+ /* GEN2 */
+ i2c@7000c400 {
+ status = "okay";
+ };
+
+ /* SD card slot */
+ sdhci@78000400 {
+ status = "okay";
+ };
+};
diff --git a/board/avionic-design/tec-ng/Makefile b/board/avionic-design/tec-ng/Makefile
new file mode 100644
index 0000000..f41eb30
--- /dev/null
+++ b/board/avionic-design/tec-ng/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2013
+# Avionic Design GmbH <www.avionic-design.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common)
+
+obj-y := ../common/tamonten-ng.o
+
+include ../../nvidia/common/common.mk
diff --git a/board/renesas/koelsch/koelsch.c b/board/renesas/koelsch/koelsch.c
index 7153f65..89f5c91 100644
--- a/board/renesas/koelsch/koelsch.c
+++ b/board/renesas/koelsch/koelsch.c
@@ -16,6 +16,8 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
+#include <netdev.h>
+#include <miiphy.h>
#include <i2c.h>
#include "qos.h"
@@ -207,6 +209,10 @@
#define SMSTPCR7 0xE615014C
#define SCIF0_MSTP721 (1 << 21)
+#define MSTPSR8 0xE61509A0
+#define SMSTPCR8 0xE6150990
+#define ETHER_MSTP813 (1 << 13)
+
#define PMMR 0xE6060000
#define GPSR4 0xE6060014
#define IPSR14 0xE6060058
@@ -241,9 +247,16 @@
mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+ /* ETHER */
+ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
+
return 0;
}
+/* LSI pin pull-up control */
+#define PUPR5 0xe6060114
+#define PUPR5_ETH 0x3FFC0000
+#define PUPR5_ETH_MAGIC (1 << 27)
int board_init(void)
{
/* adress of boot parameters */
@@ -252,9 +265,59 @@
/* Init PFC controller */
r8a7791_pinmux_init();
+ /* ETHER Enable */
+ gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
+ gpio_request(GPIO_FN_ETH_RX_ER, NULL);
+ gpio_request(GPIO_FN_ETH_RXD0, NULL);
+ gpio_request(GPIO_FN_ETH_RXD1, NULL);
+ gpio_request(GPIO_FN_ETH_LINK, NULL);
+ gpio_request(GPIO_FN_ETH_REFCLK, NULL);
+ gpio_request(GPIO_FN_ETH_MDIO, NULL);
+ gpio_request(GPIO_FN_ETH_TXD1, NULL);
+ gpio_request(GPIO_FN_ETH_TX_EN, NULL);
+ gpio_request(GPIO_FN_ETH_TXD0, NULL);
+ gpio_request(GPIO_FN_ETH_MDC, NULL);
+ gpio_request(GPIO_FN_IRQ0, NULL);
+
+ mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH & ~PUPR5_ETH_MAGIC);
+ gpio_request(GPIO_GP_5_22, NULL); /* PHY_RST */
+ mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH_MAGIC);
+
+ gpio_direction_output(GPIO_GP_5_22, 0);
+ mdelay(20);
+ gpio_set_value(GPIO_GP_5_22, 1);
+ udelay(1);
+
return 0;
}
+#define CXR24 0xEE7003C0 /* MAC address high register */
+#define CXR25 0xEE7003C8 /* MAC address low register */
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SH_ETHER
+ int ret = -ENODEV;
+ u32 val;
+ unsigned char enetaddr[6];
+
+ ret = sh_eth_initialize(bis);
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr))
+ return ret;
+
+ /* Set Mac address */
+ val = enetaddr[0] << 24 | enetaddr[1] << 16 |
+ enetaddr[2] << 8 | enetaddr[3];
+ writel(val, CXR24);
+
+ val = enetaddr[4] << 8 | enetaddr[5];
+ writel(val, CXR25);
+
+ return ret;
+#else
+ return 0;
+#endif
+}
+
int dram_init(void)
{
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
@@ -263,6 +326,20 @@
return 0;
}
+/* koelsch has KSZ8041NL/RNL */
+#define PHY_CONTROL1 0x1E
+#define PHY_LED_MODE 0xC0000
+#define PHY_LED_MODE_ACK 0x4000
+int board_phy_config(struct phy_device *phydev)
+{
+ int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
+ ret &= ~PHY_LED_MODE;
+ ret |= PHY_LED_MODE_ACK;
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
+
+ return 0;
+}
+
const struct rmobile_sysinfo sysinfo = {
CONFIG_RMOBILE_BOARD_STRING
};
@@ -280,4 +357,10 @@
void reset_cpu(ulong addr)
{
+ u8 val;
+
+ i2c_set_bus_num(2); /* PowerIC connected to ch2 */
+ i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
+ val |= 0x02;
+ i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
}
diff --git a/board/renesas/lager/lager.c b/board/renesas/lager/lager.c
index 5c99fc9..cdd5b32 100644
--- a/board/renesas/lager/lager.c
+++ b/board/renesas/lager/lager.c
@@ -18,6 +18,8 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
+#include <miiphy.h>
+#include <i2c.h>
#include "qos.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -207,6 +209,10 @@
#define SMSTPCR7 0xE615014C
#define SCIF0_MSTP721 (1 << 21)
+#define MSTPSR8 0xE61509A0
+#define SMSTPCR8 0xE6150990
+#define ETHER_MSTP813 (1 << 13)
+
#define PMMR 0xE6060000
#define GPSR4 0xE6060014
#define IPSR14 0xE6060058
@@ -242,6 +248,9 @@
mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+ /* ETHER */
+ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
+
return 0;
}
@@ -256,6 +265,68 @@
/* Init PFC controller */
r8a7790_pinmux_init();
+ /* ETHER Enable */
+ gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
+ gpio_request(GPIO_FN_ETH_RX_ER, NULL);
+ gpio_request(GPIO_FN_ETH_RXD0, NULL);
+ gpio_request(GPIO_FN_ETH_RXD1, NULL);
+ gpio_request(GPIO_FN_ETH_LINK, NULL);
+ gpio_request(GPIO_FN_ETH_REF_CLK, NULL);
+ gpio_request(GPIO_FN_ETH_MDIO, NULL);
+ gpio_request(GPIO_FN_ETH_TXD1, NULL);
+ gpio_request(GPIO_FN_ETH_TX_EN, NULL);
+ gpio_request(GPIO_FN_ETH_MAGIC, NULL);
+ gpio_request(GPIO_FN_ETH_TXD0, NULL);
+ gpio_request(GPIO_FN_ETH_MDC, NULL);
+ gpio_request(GPIO_FN_IRQ0, NULL);
+
+ gpio_request(GPIO_GP_5_31, NULL); /* PHY_RST */
+ gpio_direction_output(GPIO_GP_5_31, 0);
+ mdelay(20);
+ gpio_set_value(GPIO_GP_5_31, 1);
+ udelay(1);
+
+ return 0;
+}
+
+#define CXR24 0xEE7003C0 /* MAC address high register */
+#define CXR25 0xEE7003C8 /* MAC address low register */
+int board_eth_init(bd_t *bis)
+{
+ int ret = -ENODEV;
+
+#ifdef CONFIG_SH_ETHER
+ u32 val;
+ unsigned char enetaddr[6];
+
+ ret = sh_eth_initialize(bis);
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr))
+ return ret;
+
+ /* Set Mac address */
+ val = enetaddr[0] << 24 | enetaddr[1] << 16 |
+ enetaddr[2] << 8 | enetaddr[3];
+ writel(val, CXR24);
+
+ val = enetaddr[4] << 8 | enetaddr[5];
+ writel(val, CXR25);
+
+#endif
+
+ return ret;
+}
+
+/* lager has KSZ8041NL/RNL */
+#define PHY_CONTROL1 0x1E
+#define PHY_LED_MODE 0xC0000
+#define PHY_LED_MODE_ACK 0x4000
+int board_phy_config(struct phy_device *phydev)
+{
+ int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
+ ret &= ~PHY_LED_MODE;
+ ret |= PHY_LED_MODE_ACK;
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
+
return 0;
}
@@ -284,4 +355,11 @@
void reset_cpu(ulong addr)
{
+ u8 val;
+
+ i2c_set_bus_num(3); /* PowerIC connected to ch3 */
+ i2c_init(400000, 0);
+ i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
+ val |= 0x02;
+ i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
}
diff --git a/boards.cfg b/boards.cfg
index b662149..152d85e 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -359,9 +359,10 @@
Active arm armv7 zynq xilinx zynq zynq - Michal Simek <monstr@monstr.eu>
Active arm armv7 zynq xilinx zynq zynq_dcc zynq:ZYNQ_DCC Michal Simek <monstr@monstr.eu>
Active arm armv7:arm720t tegra114 nvidia dalmore dalmore - Tom Warren <twarren@nvidia.com>
-Active arm armv7:arm720t tegra20 avionic-design medcom-wide medcom-wide - Thierry Reding <thierry.reding@avionic-design.de>
-Active arm armv7:arm720t tegra20 avionic-design plutux plutux - Thierry Reding <thierry.reding@avionic-design.de>
-Active arm armv7:arm720t tegra20 avionic-design tec tec - Thierry Reding <thierry.reding@avionic-design.de>
+Active arm armv7:arm720t tegra20 avionic-design medcom-wide medcom-wide - Alban Bedel <alban.bedel@avionic-design.de>
+Active arm armv7:arm720t tegra20 avionic-design plutux plutux - Alban Bedel <alban.bedel@avionic-design.de>
+Active arm armv7:arm720t tegra20 avionic-design tec tec - Alban Bedel <alban.bedel@avionic-design.de>
+Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel <alban.bedel@avionic-design.de>
Active arm armv7:arm720t tegra20 compal paz00 paz00 - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 compulab trimslice trimslice - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 nvidia harmony harmony - Tom Warren <twarren@nvidia.com>
diff --git a/doc/README.rmobile b/doc/README.rmobile
index 7ec63f1..4fbbcb3 100644
--- a/doc/README.rmobile
+++ b/doc/README.rmobile
@@ -2,13 +2,15 @@
=======
This README is about U-Boot support for Renesas's ARM Cortex-A9 based RMOBILE[1]
-family of SoCs. Renesas's RMOBILE SoC family contains an ARM Cortex-A9.
+and R-Car[2]family of SoCs. Renesas's RMOBILE/R-Car SoC family contains an ARM
+Cortex-A9.
Currently the following boards are supported:
-* KMC KZM-A9-GT [2]
-
-* Atmark-Techno Armadillo-800-EVA [3]
+* KMC KZM-A9-GT [3]
+* Atmark-Techno Armadillo-800-EVA [4]
+* Renesas Electronics Lager
+* Renesas Electronics Koelsch
Toolchain
=========
@@ -17,7 +19,7 @@
But currently we compile with -march=armv5 to allow more compilers to work.
(For U-Boot code this has no performance impact.)
Because there was no compiler which is supporting armv7a not much before.
-Currently, ELDK[4], Linaro[5], CodeSourcey[6] and Emdebian[7] supports -march=armv7a
+Currently, ELDK[5], Linaro[6], CodeSourcey[7] and Emdebian[8] supports -march=armv7a
and you can get.
Build
@@ -25,13 +27,26 @@
* KZM-A9-GT
-make kzm9g_config
-make
+ make kzm9g_config
+ make
* Armadillo-800-EVA
+ make armadillo-800eva_config
+ make
+
+ Note: Armadillo-800-EVA's U-Boot supports booting from SDcard only.
+ Please see "B.2 Appendix B Boot Specifications" in hardware manual.
+
+* Lager
+
-make armadillo-800eva_config
-make
+ make lager_config
+ make
+
+* Koelsch
+
+ make koelsch_config
+ make
Links
=====
@@ -40,26 +55,30 @@
http://am.renesas.com/products/soc/assp/mobile/r_mobile/index.jsp
-[2] KZM-A9-GT
+[2] Renesas R-Car:
+
+http://am.renesas.com/products/soc/assp/automotive/index.jsp
+
+[3] KZM-A9-GT
http://www.kmckk.co.jp/kzma9-gt/index.html
-[3] Armadillo-800-EVA
+[4] Armadillo-800-EVA
http://armadillo.atmark-techno.com/armadillo-800-EVA
-[4] ELDK
+[5] ELDK
http://www.denx.de/wiki/view/ELDK-5/WebHome#Section_1.6.
-[5] Linaro
+[6] Linaro
http://www.linaro.org/downloads/
-[6] CodeSourcey
+[7] CodeSourcey
http://www.mentor.com/embedded-software/codesourcery
-[7] Emdebian
+[8] Emdebian
http://www.emdebian.org/crosstools.html
diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c
index 9847cf1..594e5dd 100644
--- a/drivers/i2c/tegra_i2c.c
+++ b/drivers/i2c/tegra_i2c.c
@@ -629,3 +629,8 @@
U_BOOT_I2C_ADAP_COMPLETE(tegra3, tegra_i2c_init, tegra_i2c_probe,
tegra_i2c_read, tegra_i2c_write,
tegra_i2c_set_bus_speed, 100000, 0, 3)
+#if TEGRA_I2C_NUM_CONTROLLERS > 4
+U_BOOT_I2C_ADAP_COMPLETE(tegra4, tegra_i2c_init, tegra_i2c_probe,
+ tegra_i2c_read, tegra_i2c_write,
+ tegra_i2c_set_bus_speed, 100000, 0, 4)
+#endif
diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h
index ea9a50e..f0a6757 100644
--- a/include/configs/at91sam9x5ek.h
+++ b/include/configs/at91sam9x5ek.h
@@ -44,7 +44,6 @@
#define LCD_BPP LCD_COLOR16
#define LCD_OUTPUT_BPP 24
#define CONFIG_LCD_LOGO
-#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
@@ -62,14 +61,15 @@
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
+/* no NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
@@ -101,9 +101,6 @@
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
-/* no NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
@@ -244,8 +241,4 @@
*/
#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000)
-#ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
-#endif
-
#endif
diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h
index 59c4948..f8cca5b 100644
--- a/include/configs/koelsch.h
+++ b/include/configs/koelsch.h
@@ -18,13 +18,18 @@
#include <asm/arch/rmobile.h>
-#define CONFIG_CMD_EDITENV
-#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_EDITENV
+#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_DFL
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_RUN
#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_FLASH
@@ -123,6 +128,20 @@
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN)
+/* SH Ether */
+#define CONFIG_NET_MULTI
+#define CONFIG_SH_ETHER
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 0x1
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define CONFIG_SH_ETHER_CACHE_INVALIDATE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+#define CONFIG_SH_ETHER_ALIGNE_SIZE 64
+
/* Board Clock */
#define CONFIG_SYS_CLK_FREQ 10000000
#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ
@@ -130,4 +149,22 @@
#define CONFIG_SYS_TMU_CLK_DIV 4
#define CONFIG_SYS_HZ 1000
+/* i2c */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SH
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 3
+#define CONFIG_SYS_I2C_SH_BASE0 0xE6500000
+#define CONFIG_SYS_I2C_SH_SPEED0 400000
+#define CONFIG_SYS_I2C_SH_BASE1 0xE6510000
+#define CONFIG_SYS_I2C_SH_SPEED1 400000
+#define CONFIG_SYS_I2C_SH_BASE2 0xE60B0000
+#define CONFIG_SYS_I2C_SH_SPEED2 400000
+#define CONFIG_SH_I2C_DATA_HIGH 4
+#define CONFIG_SH_I2C_DATA_LOW 5
+#define CONFIG_SH_I2C_CLOCK 10000000
+
+#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
+
#endif /* __KOELSCH_H */
diff --git a/include/configs/lager.h b/include/configs/lager.h
index 7819edd..8932825 100644
--- a/include/configs/lager.h
+++ b/include/configs/lager.h
@@ -28,6 +28,11 @@
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_RUN
#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_FLASH
@@ -127,12 +132,42 @@
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN)
+/* SH Ether */
+#define CONFIG_NET_MULTI
+#define CONFIG_SH_ETHER
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 0x1
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SH_ETHER_ALIGNE_SIZE 64
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define CONFIG_SH_ETHER_CACHE_INVALIDATE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_RCAR
+#define CONFIG_SYS_RCAR_I2C0_BASE 0xE6508000
+#define CONFIG_SYS_RCAR_I2C0_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C1_BASE 0xE6518000
+#define CONFIG_SYS_RCAR_I2C1_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C2_BASE 0xE6530000
+#define CONFIG_SYS_RCAR_I2C2_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C3_BASE 0xE6540000
+#define CONFIG_SYS_RCAR_I2C3_SPEED 400000
+#define CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS 4
+
+#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
+
/* Board Clock */
#define CONFIG_BASE_CLK_FREQ 20000000u
#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_BASE_CLK_FREQ / 2) /* EXT / 2 */
#define CONFIG_PLL1_CLK_FREQ (CONFIG_BASE_CLK_FREQ * 156 / 2)
#define CONFIG_PLL1_DIV2_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 2)
#define CONFIG_MP_CLK_FREQ (CONFIG_PLL1_DIV2_CLK_FREQ / 15)
+#define CONFIG_HP_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 12)
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_MP_CLK_FREQ
#define CONFIG_SYS_TMU_CLK_DIV 4
diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
new file mode 100644
index 0000000..13baa76
--- /dev/null
+++ b/include/configs/tec-ng.h
@@ -0,0 +1,84 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "tegra30-common.h"
+
+/* Enable fdt support for tec-ng. Flash the image in u-boot-dtb.bin */
+#define CONFIG_DEFAULT_DEVICE_TREE tegra30-tec-ng
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* High-level configuration options */
+#define V_PROMPT "Tegra30 (TEC-NG) # "
+#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten™ NG Evaluation Carrier"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA_ENABLE_UARTD
+#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* I2C */
+#define CONFIG_SYS_I2C_TEGRA
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA_MMC
+#define CONFIG_CMD_MMC
+
+/* Environment in eMMC, at the end of 2nd "boot sector" */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 2
+
+/* SPI */
+#define CONFIG_TEGRA20_SLINK
+#define CONFIG_TEGRA_SLINK_CTRLS 6
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_SIZE (4 << 20)
+
+/* USB Host support */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_TEGRA
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+
+/* USB networking support */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* General networking support */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+
+/* Tag support */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
+#include "tegra-common-post.h"
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/tegra114-common.h b/include/configs/tegra114-common.h
index c3de9a9..a4e8a5f 100644
--- a/include/configs/tegra114-common.h
+++ b/include/configs/tegra114-common.h
@@ -82,5 +82,6 @@
/* For USB EHCI controller */
#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10
#endif /* _TEGRA114_COMMON_H_ */
diff --git a/include/configs/tegra30-common.h b/include/configs/tegra30-common.h
index 99acbfd..b5550d7 100644
--- a/include/configs/tegra30-common.h
+++ b/include/configs/tegra30-common.h
@@ -79,5 +79,6 @@
/* For USB EHCI controller */
#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10
#endif /* _TEGRA30_COMMON_H_ */