include/configs: Use new CONFIG_CMD_* in various [v-z]* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 3b106ef..853e4bc 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -239,11 +239,7 @@
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
-#define CMD_USB (CFG_CMD_USB | CFG_CMD_FAT | CFG_CMD_EXT2)
-
#define CONFIG_SUPPORT_VFAT
-#else
-#define CMD_USB 0 /* no USB on 440GR */
#endif /* CONFIG_440EP */
#ifdef DEBUG
@@ -252,32 +248,40 @@
#define CONFIG_HW_WATCHDOG /* watchdog */
#endif
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CMD_USB)
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#ifdef CONFIG_440EP
+ #define CONFIG_CMD_USB
+ #define CONFIG_CMD_FAT
+ #define CONFIG_CMD_EXT2
+#endif
+
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -344,7 +348,7 @@
*/
#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
@@ -356,7 +360,7 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif