rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h
index fd13dcd..a3f2677 100644
--- a/include/configs/smmaco4.h
+++ b/include/configs/smmaco4.h
@@ -37,7 +37,7 @@
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
@@ -49,7 +49,7 @@
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/* Partitions */
#define CONFIG_MAC_PARTITION
@@ -57,9 +57,9 @@
#define CONFIG_ISO_PARTITION
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_I2C)
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
@@ -101,7 +101,7 @@
#define CONFIG_TIMESTAMP /* display image timestamps */
#if (TEXT_BASE == 0xFC000000) /* Boot low */
-# define CFG_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT 1
#endif
/*
@@ -143,17 +143,17 @@
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
+#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
* of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
+#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
@@ -161,9 +161,9 @@
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#ifdef CONFIG_TQM5200_REV100
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
+#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
#else
-#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
#endif
/*
@@ -172,11 +172,11 @@
* Please notice, that the resulting clock frequency could differ from the
* configured value. This is because the I2C clock is derived from system
* clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CFG_I2C_SPEED. However the calculated
+ * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
* approximation allways lies below the configured value, never above.
*/
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
@@ -184,34 +184,34 @@
* EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
* same configuration could be used.
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
+#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */
/* use CFI flash driver if no module variant is spezified */
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
-#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
-#if !defined(CFG_LOWBOOT)
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
-#endif /* CFG_LOWBOOT */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/* Dynamic MTD partition support */
#define CONFIG_JFFS2_CMDLINE
@@ -235,32 +235,32 @@
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use ON-Chip SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
#else
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
#endif
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
@@ -299,19 +299,19 @@
* tests.
*/
#if defined (CONFIG_MINIFAP)
-# define CFG_GPS_PORT_CONFIG 0x91000004
+# define CONFIG_SYS_GPS_PORT_CONFIG 0x91000004
#elif defined (CONFIG_STK52XX)
# if defined (CONFIG_STK52XX_REV100)
-# define CFG_GPS_PORT_CONFIG 0x81500014
+# define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014
# else /* STK52xx REV200 and above */
# if defined (CONFIG_TQM5200_REV100)
# error TQM5200 REV100 not supported on STK52XX REV200 or above
# else/* TQM5200 REV200 and above */
-# define CFG_GPS_PORT_CONFIG 0x91500004
+# define CONFIG_SYS_GPS_PORT_CONFIG 0x91500004
# endif
# endif
#else /* TMQ5200 Inbetriebnahme-Board */
-# define CFG_GPS_PORT_CONFIG 0x81000004
+# define CONFIG_SYS_GPS_PORT_CONFIG 0x81000004
#endif
/*
@@ -322,30 +322,30 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/* Enable an alternate, more extensive memory test */
-#define CFG_ALT_MEMTEST
+#define CONFIG_SYS_ALT_MEMTEST
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
@@ -357,26 +357,26 @@
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL 0
#endif
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
-#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
+#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
-#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
#endif
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
-#define CFG_RESET_ADDRESS 0xff000000
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
#endif /* __CONFIG_H */