diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h
index 0a9800a..9b03ac2 100644
--- a/include/configs/hcu4.h
+++ b/include/configs/hcu4.h
@@ -45,46 +45,46 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
 *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN	(320 * 1024)	/* Reserve 320 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(256 * 1024) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN	(320 * 1024)	/* Reserve 320 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(256 * 1024) /* Reserve 256 kB for malloc() */
 
 
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
-#define CFG_FLASH_BASE		0xfff80000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CONFIG_SYS_FLASH_BASE		0xfff80000	/* start of FLASH	*/
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
 
 /* ... with on-chip memory here (4KBytes) */
-#define CFG_OCM_DATA_ADDR 0xF4000000
-#define CFG_OCM_DATA_SIZE 0x00001000
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
 /* Do not set up locked dcache as init ram. */
-#undef CFG_INIT_DCACHE_CS
+#undef CONFIG_SYS_INIT_DCACHE_CS
 
 /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
 
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR	/* OCM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE
-#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR	/* OCM		*/
+#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE
+#define CONFIG_SYS_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 /*
- * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
- * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
-#undef CFG_EXT_SERIAL_CLOCK	       /* external serial clock */
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK	       /* external serial clock */
 #define CONFIG_SERIAL_MULTI  1
 /* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */
-#undef	CFG_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_SYS_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD	    691200
 
 /* Size (bytes) of interrupt driven serial port buffer.
  * Set to 0 to use polling instead of interrupts.
@@ -96,7 +96,7 @@
 #define CONFIG_BAUDRATE		9600
 
 
-#define CFG_BAUDRATE_TABLE						\
+#define CONFIG_SYS_BAUDRATE_TABLE						\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
@@ -104,18 +104,18 @@
  *----------------------------------------------------------------------*/
 
 /* Use common CFI driver */
-#define CFG_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 /* board provides its own flash_init code */
 #define CONFIG_FLASH_CFI_LEGACY		1
-#define CFG_FLASH_CFI_WIDTH		FLASH_CFI_8BIT
-#define CFG_FLASH_LEGACY_512Kx8 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_8BIT
+#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
 
 /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_EMPTY_INFO
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CFG_MAX_FLASH_SECT	8	/* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip */
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -135,7 +135,7 @@
 #ifdef CONFIG_ENV_IS_IN_FLASH
 /* Put the environment in Flash */
 #define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector	*/
-#define CONFIG_ENV_ADDR		((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR		((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE		8*1024	/* 8 KB Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
@@ -147,22 +147,22 @@
  * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
  * the first internal I2C controller of the PPC440EPx
  *----------------------------------------------------------------------*/
-#define CFG_SPD_BUS_NUM		0
+#define CONFIG_SYS_SPD_BUS_NUM		0
 
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
 /* This is the 7bit address of the device, not including P. */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 
 /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CFG_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+#undef CONFIG_SYS_I2C_MULTI_EEPROMS
 
 
 #define CONFIG_PREBOOT	"echo;"						\
@@ -178,7 +178,7 @@
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
 #define CONFIG_SERVERIP		172.25.1.3
 
-#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */
 
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"netdev=eth0\0"							\
@@ -208,7 +208,7 @@
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR	1	/* PHY address			*/
@@ -216,7 +216,7 @@
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup */
 
 #define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER	16 /* Number of ethernet rx buffers & desC */
+#define CONFIG_SYS_RX_ETH_BUFFER	16 /* Number of ethernet rx buffers & desC */
 
 /*
  * BOOTP options
@@ -252,42 +252,42 @@
 #define SPD_EEPROM_ADDRESS      0x50
 
 /* POST support */
-#define CONFIG_POST		(CFG_POST_MEMORY   | \
-				 CFG_POST_CPU	   | \
-				 CFG_POST_UART	   | \
-				 CFG_POST_I2C	   | \
-				 CFG_POST_CACHE	   | \
-				 CFG_POST_ETHER	   | \
-				 CFG_POST_SPR)
+#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
+				 CONFIG_SYS_POST_CPU	   | \
+				 CONFIG_SYS_POST_UART	   | \
+				 CONFIG_SYS_POST_I2C	   | \
+				 CONFIG_SYS_POST_CACHE	   | \
+				 CONFIG_SYS_POST_ETHER	   | \
+				 CONFIG_SYS_POST_SPR)
 
-#define CFG_POST_UART_TABLE	{UART0_BASE}
-#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_POST_UART_TABLE	{UART0_BASE}
+#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 #undef  CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-	#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
-	#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
@@ -297,50 +297,50 @@
  * External Bus Controller (EBC) Setup
  */
 
-#define CFG_EBC_CFG	0x98400000
+#define CONFIG_SYS_EBC_CFG	0x98400000
 
 /* Memory Bank 0 (Flash Bank 0) initialization	*/
-#define CFG_EBC_PB0AP	0x02005400
-#define CFG_EBC_PB0CR	0xFFF18000  /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB0AP	0x02005400
+#define CONFIG_SYS_EBC_PB0CR	0xFFF18000  /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
 
-#define CFG_EBC_PB1AP	0x03041200
-#define CFG_EBC_PB1CR	0x7009A000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+#define CONFIG_SYS_EBC_PB1AP	0x03041200
+#define CONFIG_SYS_EBC_PB1CR	0x7009A000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
 
-#define CFG_EBC_PB2AP	0x02054500
-#define CFG_EBC_PB2CR	0x78018000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+#define CONFIG_SYS_EBC_PB2AP	0x02054500
+#define CONFIG_SYS_EBC_PB2CR	0x78018000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
 
-#define CFG_EBC_PB3AP	0x01840300
-#define CFG_EBC_PB3CR	0x7c0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+#define CONFIG_SYS_EBC_PB3AP	0x01840300
+#define CONFIG_SYS_EBC_PB3CR	0x7c0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
 
-#define CFG_EBC_PB4AP	0x01800300
-#define CFG_EBC_PB4CR	0x7e0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+#define CONFIG_SYS_EBC_PB4AP	0x01800300
+#define CONFIG_SYS_EBC_PB4CR	0x7e0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
 
-#define CFG_GPIO0_OR	0xF27FFFFF  /* GPIO value */
-#define CFG_GPIO0_TCR	0x7FFE0000  /* GPIO value */
-#define CFG_GPIO0_ODR	0x00E897FC  /* GPIO value */
+#define CONFIG_SYS_GPIO0_OR	0xF27FFFFF  /* GPIO value */
+#define CONFIG_SYS_GPIO0_TCR	0x7FFE0000  /* GPIO value */
+#define CONFIG_SYS_GPIO0_ODR	0x00E897FC  /* GPIO value */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)/* Initial Memory map for Linux */
 
 /* Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */
 
-#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0	*/
+#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
 
 
 /* Configuration Port location */
 #define CONFIG_PORT_ADDR	0xF0000500
 
-#define CFG_HUSH_PARSER                 /* use "hush" command parser    */
-#ifdef  CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_HUSH_PARSER                 /* use "hush" command parser    */
+#ifdef  CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if defined(CONFIG_CMD_KGDB)