diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 4eee21c..678e1e1 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -31,10 +31,10 @@
 #endif
 
 #ifdef RUN_DIAG
-#define CFG_DIAG_ADDR		0xff800000
+#define CONFIG_SYS_DIAG_ADDR		0xff800000
 #endif
 
-#define CFG_RESET_ADDRESS	0xfff00100
+#define CONFIG_SYS_RESET_ADDRESS	0xfff00100
 
 #define CONFIG_PCI		1	/* Enable PCI/PCIE*/
 #define CONFIG_PCI1		1	/* PCI controler 1 */
@@ -52,7 +52,7 @@
 /*
  * L2CR setup -- make sure this is right for your board!
  */
-#define CFG_L2
+#define CONFIG_SYS_L2
 #define L2_INIT		0
 #define L2_ENABLE	(L2CR_L2E |0x00100000 )
 
@@ -63,22 +63,22 @@
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
 #define CONFIG_MISC_INIT_R		1
 
-#define CFG_MEMTEST_START	0x00200000	/* memtest region */
-#define CFG_MEMTEST_END		0x00400000
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
 
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
-#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
-#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
-#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCI1_ADDR		(CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE1_ADDR		(CONFIG_SYS_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCIE2_ADDR		(CONFIG_SYS_CCSRBAR+0x9000)
 
-#define CFG_DIU_ADDR		(CFG_CCSRBAR+0x2c000)
+#define CONFIG_SYS_DIU_ADDR		(CONFIG_SYS_CCSRBAR+0x2c000)
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -89,8 +89,8 @@
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_VERY_BIG_RAM
 
 #define MPC86xx_DDR_SDRAM_CLK_CNTL
@@ -102,64 +102,64 @@
 #define SPD_EEPROM_ADDRESS1	0x51	/* CTLR 0 DIMM 0 */
 
 /* These are used when DDR doesn't use SPD.  */
-#define CFG_SDRAM_SIZE	256		/* DDR is 256MB */
+#define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */
 
 #if 0 /* TODO */
-#define CFG_DDR_CS0_BNDS	0x0000000F
-#define CFG_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
-#define CFG_DDR_TIMING_3	0x00000000
-#define CFG_DDR_TIMING_0	0x00260802
-#define CFG_DDR_TIMING_1	0x3935d322
-#define CFG_DDR_TIMING_2	0x14904cc8
-#define CFG_DDR_MODE_1		0x00480432
-#define CFG_DDR_MODE_2		0x00000000
-#define CFG_DDR_INTERVAL	0x06180100
-#define CFG_DDR_DATA_INIT	0xdeadbeef
-#define CFG_DDR_CLK_CTRL	0x03800000
-#define CFG_DDR_OCD_CTRL	0x00000000
-#define CFG_DDR_OCD_STATUS	0x00000000
-#define CFG_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
-#define CFG_DDR_CONTROL2	0x04400010
+#define CONFIG_SYS_DDR_CS0_BNDS	0x0000000F
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	0x00260802
+#define CONFIG_SYS_DDR_TIMING_1	0x3935d322
+#define CONFIG_SYS_DDR_TIMING_2	0x14904cc8
+#define CONFIG_SYS_DDR_MODE_1		0x00480432
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_INTERVAL	0x06180100
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL	0x03800000
+#define CONFIG_SYS_DDR_OCD_CTRL	0x00000000
+#define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
+#define CONFIG_SYS_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2	0x04400010
 
-#define CFG_DDR_ERR_INT_EN	0x00000000
-#define CFG_DDR_ERR_DIS		0x00000000
-#define CFG_DDR_SBE		0x000f0000
+#define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
+#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
+#define CONFIG_SYS_DDR_SBE		0x000f0000
 
 /*
  * FIXME: Not used in fixed_sdram function
  */
-#define CFG_DDR_MODE		0x00000022
-#define CFG_DDR_CS1_BNDS	0x00000000
-#define CFG_DDR_CS2_BNDS	0x00000FFF	/* Not done */
-#define CFG_DDR_CS3_BNDS	0x00000FFF	/* Not done */
-#define CFG_DDR_CS4_BNDS	0x00000FFF	/* Not done */
-#define CFG_DDR_CS5_BNDS	0x00000FFF	/* Not done */
+#define CONFIG_SYS_DDR_MODE		0x00000022
+#define CONFIG_SYS_DDR_CS1_BNDS	0x00000000
+#define CONFIG_SYS_DDR_CS2_BNDS	0x00000FFF	/* Not done */
+#define CONFIG_SYS_DDR_CS3_BNDS	0x00000FFF	/* Not done */
+#define CONFIG_SYS_DDR_CS4_BNDS	0x00000FFF	/* Not done */
+#define CONFIG_SYS_DDR_CS5_BNDS	0x00000FFF	/* Not done */
 #endif
 
 
 #define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_NXID
+#define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_ADDR     0x57
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 
 
-#define CFG_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
-#define CFG_FLASH_BASE2		0xf8000000
+#define CONFIG_SYS_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
+#define CONFIG_SYS_FLASH_BASE2		0xf8000000
 
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 
-#define CFG_BR0_PRELIM		0xf8001001 /* port size 16bit */
-#define CFG_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/
+#define CONFIG_SYS_BR0_PRELIM		0xf8001001 /* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/
 
-#define CFG_BR1_PRELIM		0xf0001001 /* port size 16bit */
-#define CFG_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
+#define CONFIG_SYS_BR1_PRELIM		0xf0001001 /* port size 16bit */
+#define CONFIG_SYS_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
 #if 0 /* TODO */
-#define CFG_BR2_PRELIM		0xf0000000
-#define CFG_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
+#define CONFIG_SYS_BR2_PRELIM		0xf0000000
+#define CONFIG_SYS_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
 #endif
-#define CFG_BR3_PRELIM		0xe8000801 /* port size 8bit */
-#define CFG_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
+#define CONFIG_SYS_BR3_PRELIM		0xe8000801 /* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
 
 
 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
@@ -179,67 +179,67 @@
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
-#define CFG_PIXIS_VBOOT_MASK	0x0C    /* Reset altbank mask*/
+#define CONFIG_SYS_PIXIS_VBOOT_MASK	0x0C    /* Reset altbank mask*/
 
-#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
-#define CFG_MAX_FLASH_SECT	1024		/* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
 
-#undef	CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
 
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
 #else
-#undef	CFG_RAMBOOT
+#undef	CONFIG_SYS_RAMBOOT
 #endif
 
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
 #undef CONFIG_SPD_EEPROM
-#define CFG_SDRAM_SIZE	256
+#define CONFIG_SYS_SDRAM_SIZE	256
 #endif
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
 #define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK	1
-#ifndef CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#ifndef CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
 #else
-#define CFG_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
 #endif
-#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_END	0x4000		/* End of used area in RAM */
 
-#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	128		/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
-#define CFG_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE	1
-#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 
-#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
 /* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef	CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /*
@@ -253,8 +253,8 @@
 /* maximum size of the flat tree (8K) */
 #define OF_FLAT_TREE_MAX_SIZE	8192
 
-#define CFG_64BIT_VSPRINTF	1
-#define CFG_64BIT_STRTOUL	1
+#define CONFIG_SYS_64BIT_VSPRINTF	1
+#define CONFIG_SYS_64BIT_STRTOUL	1
 
 /*
  * I2C
@@ -262,46 +262,46 @@
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
-#define CFG_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3000
 
 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
-#define CFG_PCI1_MEM_BASE	0x80000000
-#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCI1_IO_BASE	0x00000000
-#define CFG_PCI1_IO_PHYS	0xe1000000
-#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
 
 /* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS	0x00000000
-#define CFG_PCI_MEMORY_PHYS	0x00000000
-#define CFG_PCI_MEMORY_SIZE	0x80000000
+#define CONFIG_SYS_PCI_MEMORY_BUS	0x00000000
+#define CONFIG_SYS_PCI_MEMORY_PHYS	0x00000000
+#define CONFIG_SYS_PCI_MEMORY_SIZE	0x80000000
 
 /* For RTL8139 */
 #define KSEG1ADDR(x)	({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
 #define _IO_BASE		0x00000000
 
 /* controller 1, Base address 0xa000 */
-#define CFG_PCIE1_MEM_BASE	0xa0000000
-#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCIE1_IO_BASE	0x00000000
-#define CFG_PCIE1_IO_PHYS	0xe3000000
-#define CFG_PCIE1_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xe3000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/* 1M */
 
 /* controller 2, Base Address 0x9000 */
-#define CFG_PCIE2_MEM_BASE	0x90000000
-#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
-#define CFG_PCIE2_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCIE2_IO_BASE	0x00000000	/* reuse mem LAW */
-#define CFG_PCIE2_IO_PHYS	0xe2000000
-#define CFG_PCIE2_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCIE2_MEM_BASE	0x90000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000	/* reuse mem LAW */
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xe2000000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00100000	/* 1M */
 
 
 #if defined(CONFIG_PCI)
@@ -324,11 +324,11 @@
 #define CONFIG_PCI_OHCI		1
 #define CONFIG_USB_OHCI_NEW		1
 #define CONFIG_USB_KEYBOARD	1
-#define CFG_DEVICE_DEREGISTER
-#define CFG_USB_EVENT_POLL	1
-#define CFG_USB_OHCI_SLOT_NAME	"ohci_pci"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
-#define CFG_OHCI_SWAP_REG_ACCESS	1
+#define CONFIG_SYS_DEVICE_DEREGISTER
+#define CONFIG_SYS_USB_EVENT_POLL	1
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1
 
 #if !defined(CONFIG_PCI_PNP)
 #define PCI_ENET0_IOADDR	0xe0000000
@@ -341,10 +341,10 @@
 
 #ifdef CONFIG_SCSI_AHCI
 #define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID	4
-#define CFG_SCSI_MAX_LUN	1
-#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
+#define CONFIG_SYS_SCSI_MAX_LUN	1
+#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
 #endif
 
 #endif	/* CONFIG_PCI */
@@ -353,10 +353,10 @@
  * BAT0		2G	Cacheable, non-guarded
  * 0x0000_0000	2G	DDR
  */
-#define CFG_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
-#define CFG_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE )
-#define CFG_IBAT0U	CFG_DBAT0U
+#define CONFIG_SYS_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CONFIG_SYS_IBAT0U	CONFIG_SYS_DBAT0U
 
 /*
  * BAT1		1G	Cache-inhibited, guarded
@@ -365,22 +365,22 @@
  * 0x9000_0000	256M	PCI-Express 2 Memory
  */
 
-#define CFG_DBAT1L	(CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U	(CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
-#define CFG_IBAT1L	(CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT1U	CFG_DBAT1U
+#define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
 
 /*
  * BAT2		16M	Cache-inhibited, guarded
  * 0xe100_0000	1M	PCI-1 I/O
  */
 
-#define CFG_DBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U	(CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U	CFG_DBAT2U
+#define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
 
 /*
  * BAT3		32M	Cache-inhibited, guarded
@@ -388,68 +388,68 @@
  * 0xe300_0000	1M	PCI-Express 1 I/O
  */
 
-#define CFG_DBAT3L	(CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U	(CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L	(CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U	CFG_DBAT3U
+#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
 
 /*
  * BAT4		4M	Cache-inhibited, guarded
  * 0xe000_0000	4M	CCSR
  */
-#define CFG_DBAT4L	(CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U	(CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L	(CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT4U	CFG_DBAT4U
+#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
 
 /*
  * BAT5		128K	Cacheable, non-guarded
  * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
  */
-#define CFG_DBAT5L	(CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT5U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT5L	CFG_DBAT5L
-#define CFG_IBAT5U	CFG_DBAT5U
+#define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
+#define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
 
 /*
  * BAT6		256M	Cache-inhibited, guarded
  * 0xf000_0000	256M	FLASH
  */
-#define CFG_DBAT6L	(CFG_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U	(CFG_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L	(CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U	CFG_DBAT6U
+#define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
 
 /*
  * BAT7		4M	Cache-inhibited, guarded
  * 0xe800_0000	4M	PIXIS
  */
-#define CFG_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CFG_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT7U	CFG_DBAT7U
+#define CONFIG_SYS_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U
 
 
 /*
  * Environment
  */
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
 #define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 126k (one sector) for env */
 #define CONFIG_ENV_SIZE		0x2000
 #else
 #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 
 /*
@@ -470,7 +470,7 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
 #undef CONFIG_CMD_ENV
 #endif
 
@@ -483,7 +483,7 @@
 
 
 #define CONFIG_WATCHDOG			/* watchdog enabled */
-#define CFG_WATCHDOG_FREQ	5000	/* Feed interval, 5s */
+#define CONFIG_SYS_WATCHDOG_FREQ	5000	/* Feed interval, 5s */
 
 /*DIU Configuration*/
 #define DIU_CONNECT_TO_DVI		/* DIU controller connects to DVI encoder*/
@@ -491,28 +491,28 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
-#define CFG_LOAD_ADDR	0x2000000	/* default load address */
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args */
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions