rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h
index e087624..489378a 100644
--- a/include/configs/CPU87.h
+++ b/include/configs/CPU87.h
@@ -87,10 +87,10 @@
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
@@ -100,10 +100,10 @@
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
@@ -129,8 +129,8 @@
*/
#define CONFIG_SOFT_I2C /* Software I2C support enabled */
-# define CFG_I2C_SPEED 50000
-# define CFG_I2C_SLAVE 0xFE
+# define CONFIG_SYS_I2C_SPEED 50000
+# define CONFIG_SYS_I2C_SLAVE 0xFE
/*
* Software (bit-bang) I2C driver configuration
*/
@@ -145,7 +145,7 @@
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_RTC_PCF8563
-#define CFG_I2C_RTC_ADDR 0x51
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -153,17 +153,17 @@
* Disk-On-Chip configuration
*/
-#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-#define CFG_DOC_SUPPORT_2000
-#define CFG_DOC_SUPPORT_MILLENNIUM
+#define CONFIG_SYS_DOC_SUPPORT_2000
+#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
/*-----------------------------------------------------------------------
* Miscellaneous configuration options
*/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
/*
* BOOTP options
@@ -196,27 +196,27 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_RESET_ADDRESS 0xFFF00100 /* "bad" address */
+#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */
#define CONFIG_LOOPW
@@ -225,135 +225,135 @@
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* Flash configuration
*/
-#define CFG_BOOTROM_BASE 0xFF800000
-#define CFG_BOOTROM_SIZE 0x00080000
-#define CFG_FLASH_BASE 0xFF000000
-#define CFG_FLASH_SIZE 0x00800000
+#define CONFIG_SYS_BOOTROM_BASE 0xFF800000
+#define CONFIG_SYS_BOOTROM_SIZE 0x00080000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 0x00800000
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 135 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max num of sects on one chip */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/*-----------------------------------------------------------------------
* Other areas to be mapped
*/
/* CS3: Dual ported SRAM */
-#define CFG_DPSRAM_BASE 0x40000000
-#define CFG_DPSRAM_SIZE 0x00100000
+#define CONFIG_SYS_DPSRAM_BASE 0x40000000
+#define CONFIG_SYS_DPSRAM_SIZE 0x00100000
/* CS4: DiskOnChip */
-#define CFG_DOC_BASE 0xF4000000
-#define CFG_DOC_SIZE 0x00100000
+#define CONFIG_SYS_DOC_BASE 0xF4000000
+#define CONFIG_SYS_DOC_SIZE 0x00100000
/* CS5: FDC37C78 controller */
-#define CFG_FDC37C78_BASE 0xF1000000
-#define CFG_FDC37C78_SIZE 0x00100000
+#define CONFIG_SYS_FDC37C78_BASE 0xF1000000
+#define CONFIG_SYS_FDC37C78_SIZE 0x00100000
/* CS6: Board configuration registers */
-#define CFG_BCRS_BASE 0xF2000000
-#define CFG_BCRS_SIZE 0x00010000
+#define CONFIG_SYS_BCRS_BASE 0xF2000000
+#define CONFIG_SYS_BCRS_SIZE 0x00010000
/* CS7: VME Extended Access Range */
-#define CFG_VMEEAR_BASE 0x60000000
-#define CFG_VMEEAR_SIZE 0x01000000
+#define CONFIG_SYS_VMEEAR_BASE 0x60000000
+#define CONFIG_SYS_VMEEAR_SIZE 0x01000000
/* CS8: VME Standard Access Range */
-#define CFG_VMESAR_BASE 0xFE000000
-#define CFG_VMESAR_SIZE 0x01000000
+#define CONFIG_SYS_VMESAR_BASE 0xFE000000
+#define CONFIG_SYS_VMESAR_SIZE 0x01000000
/* CS9: VME Short I/O Access Range */
-#define CFG_VMESIOAR_BASE 0xFD000000
-#define CFG_VMESIOAR_SIZE 0x01000000
+#define CONFIG_SYS_VMESIOAR_BASE 0xFD000000
+#define CONFIG_SYS_VMESIOAR_SIZE 0x01000000
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*
- * if you change bits in the HRCW, you must also change the CFG_*
+ * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
* defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
*/
#if defined(CONFIG_BOOT_ROM)
-#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
+#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
HRCW_BPS01 | HRCW_CS10PC01)
#else
-#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01)
+#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01)
#endif
/* no slaves so just fill with zeros */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xF0000000
+#define CONFIG_SYS_IMMR 0xF0000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*
- * 60x SDRAM is mapped at CFG_SDRAM_BASE.
+ * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
#endif
#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_EEPRO100
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#endif
#if 0
/* environment is in Flash */
#define CONFIG_ENV_IS_IN_FLASH 1
#ifdef CONFIG_BOOT_ROM
-# define CONFIG_ENV_ADDR (CFG_FLASH_BASE+0x70000)
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x70000)
# define CONFIG_ENV_SIZE 0x10000
# define CONFIG_ENV_SECT_SIZE 0x10000
#endif
#else
/* environment is in EEPROM */
#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CONFIG_ENV_OFFSET 512
#define CONFIG_ENV_SIZE (2048 - 512)
#endif
@@ -370,9 +370,9 @@
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -385,30 +385,30 @@
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register 5-5
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
-#define CFG_RMR RMR_CSRE
+#define CONFIG_SYS_RMR RMR_CSRE
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
#define BCR_APD01 0x10000000
-#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\
+#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\
SIUMCR_CS10PC01|SIUMCR_BCTLC10)
/*-----------------------------------------------------------------------
@@ -418,10 +418,10 @@
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
@@ -431,7 +431,7 @@
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
@@ -439,22 +439,22 @@
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
* Ensure DFBRG is Divide by 16
*/
-#define CFG_SCCR SCCR_DFBRG01
+#define CONFIG_SYS_SCCR SCCR_DFBRG01
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
-#define CFG_MIN_AM_MASK 0xC0000000
+#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
/*
* we use the same values for 32 MB, 128 MB and 256 MB SDRAM
@@ -465,13 +465,13 @@
* MPTPR - Memory Refresh Timer Prescaler Register 10-18
*-----------------------------------------------------------------------
*/
-#define CFG_MPTPR 0x2000
+#define CONFIG_SYS_MPTPR 0x2000
/*-----------------------------------------------------------------------
* PSRT - Refresh Timer Register 10-16
*-----------------------------------------------------------------------
*/
-#define CFG_PSRT 0x16
+#define CONFIG_SYS_PSRT 0x16
/*-----------------------------------------------------------------------
* PSRT - SDRAM Mode Register 10-10
@@ -480,12 +480,12 @@
/* SDRAM initialization values for 8-column chips
*/
-#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\
+#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A9 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
+#define CONFIG_SYS_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
PSDMR_BSMA_A14_A16 |\
PSDMR_SDA10_PBI0_A10 |\
PSDMR_RFRC_7_CLK |\
@@ -497,12 +497,12 @@
/* SDRAM initialization values for 9-column chips
*/
-#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\
+#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A7 |\
ORxS_NUMR_13)
-#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
+#define CONFIG_SYS_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A13_A15 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_RFRC_7_CLK |\
@@ -514,12 +514,12 @@
/* SDRAM initialization values for 10-column chips
*/
-#define CFG_OR2_10COL (CFG_MIN_AM_MASK |\
+#define CONFIG_SYS_OR2_10COL (CONFIG_SYS_MIN_AM_MASK |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A4 |\
ORxS_NUMR_13)
-#define CFG_PSDMR_10COL (PSDMR_PBI |\
+#define CONFIG_SYS_PSDMR_10COL (PSDMR_PBI |\
PSDMR_SDAM_A17_IS_A5 |\
PSDMR_BSMA_A13_A15 |\
PSDMR_SDA10_PBI1_A6 |\
@@ -541,17 +541,17 @@
*
*/
-#define CFG_MRS_OFFS 0x00000000
+#define CONFIG_SYS_MRS_OFFS 0x00000000
#ifdef CONFIG_BOOT_ROM
/* Bank 0 - Boot ROM
*/
-#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
@@ -559,12 +559,12 @@
/* Bank 1 - FLASH
*/
-#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
@@ -573,12 +573,12 @@
#else /* CONFIG_BOOT_ROM */
/* Bank 0 - FLASH
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
@@ -586,12 +586,12 @@
/* Bank 1 - Boot ROM
*/
-#define CFG_BR1_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\
+#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
@@ -602,25 +602,25 @@
/* Bank 2 - 60x bus SDRAM
*/
-#ifndef CFG_RAMBOOT
-#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+#ifndef CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR2_PRELIM CFG_OR2_8COL
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
-#define CFG_PSDMR CFG_PSDMR_8COL
-#endif /* CFG_RAMBOOT */
+#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_8COL
+#endif /* CONFIG_SYS_RAMBOOT */
/* Bank 3 - Dual Ported SRAM
*/
-#define CFG_BR3_PRELIM ((CFG_DPSRAM_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_DPSRAM_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_DPSRAM_SIZE) |\
+#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DPSRAM_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_7_CLK |\
@@ -628,12 +628,12 @@
/* Bank 4 - DiskOnChip
*/
-#define CFG_BR4_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR4_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\
+#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV2 |\
ORxG_SCY_9_CLK |\
@@ -641,35 +641,35 @@
/* Bank 5 - FDC37C78 controller
*/
-#define CFG_BR5_PRELIM ((CFG_FDC37C78_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FDC37C78_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR5_PRELIM (P2SZ_TO_AM(CFG_FDC37C78_SIZE) |\
+#define CONFIG_SYS_OR5_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FDC37C78_SIZE) |\
ORxG_ACS_DIV2 |\
ORxG_SCY_10_CLK |\
ORxU_EHTR_8IDLE)
/* Bank 6 - Board control registers
*/
-#define CFG_BR6_PRELIM ((CFG_BCRS_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_BCRS_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR6_PRELIM (P2SZ_TO_AM(CFG_BCRS_SIZE) |\
+#define CONFIG_SYS_OR6_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BCRS_SIZE) |\
ORxG_CSNT |\
ORxG_SCY_7_CLK)
/* Bank 7 - VME Extended Access Range
*/
-#define CFG_BR7_PRELIM ((CFG_VMEEAR_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_VMEEAR_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR7_PRELIM (P2SZ_TO_AM(CFG_VMEEAR_SIZE) |\
+#define CONFIG_SYS_OR7_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMEEAR_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_7_CLK |\
@@ -677,12 +677,12 @@
/* Bank 8 - VME Standard Access Range
*/
-#define CFG_BR8_PRELIM ((CFG_VMESAR_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_VMESAR_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR8_PRELIM (P2SZ_TO_AM(CFG_VMESAR_SIZE) |\
+#define CONFIG_SYS_OR8_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESAR_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_7_CLK |\
@@ -690,12 +690,12 @@
/* Bank 9 - VME Short I/O Access Range
*/
-#define CFG_BR9_PRELIM ((CFG_VMESIOAR_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR9_PRELIM ((CONFIG_SYS_VMESIOAR_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR9_PRELIM (P2SZ_TO_AM(CFG_VMESIOAR_SIZE) |\
+#define CONFIG_SYS_OR9_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VMESIOAR_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_7_CLK |\